Huawei SmartAX MA5603T Configuration Manual page 522

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
Procedure
Step 1 Configure the basic MPLS.
1.
2.
3.
4.
5.
Step 2 Configure VLAN, and enable MPLS for VLAN and VLAN interfaces.
1.
2.
3.
Step 3 Configure routes.
VPLS has no special requirements on routing policy. You can use static route, RIP, or OSPF
policy. In the following example, OSPF is used.
Set the OSPF process ID to 100 and OSPF area ID to 1. In addition, configure the interfaces
(VLAN interface and loopback interface) that run OSPF and configure the areas of the interfaces.
huawei(config)#ospf 1
huawei(config-ospf-1)#area 100
huawei(config-ospf-1-area-0.0.0.100)#network 10.50.50.0 0.0.0.255
huawei(config-ospf-1-area-0.0.0.100)#network 10.10.10.10 0.0.0.0
huawei(config-ospf-1-area-0.0.0.100)#return
Step 4 Configure the remote LDP session.
Configure the remote LDP sessions from the MA5600T/MA5603T/MA5608T to SPE1 (LSR
ID: 1.1.1.1) and SPE2 (LSR ID: 2.2.2.2) respectively. Name the sessions to_spe1 and to_spe2
respectively.
Issue 01 (2014-04-30)
Configure a loopback interface.
Set the ID of the loopback interface to 0 and its IP address to 10.10.10.10/32.
huawei(config)#interface loopback 0
huawei(config-if-loopback0)#ip address 10.10.10.10 32
huawei(config-if-loopback0)#quit
Configure the MPLS LSR-ID. Use the IP address of loopback interface 0 as the LSR ID.
huawei(config)#mpls lsr-id 10.10.10.10
Enable MPLS globally.
Trigger LDP by the IP address of the host to set up an LSP.
huawei(config)#mpls
huawei(config-mpls)#lsp-trigger host
huawei(config-mpls)#quit
Enable the L2VPN function.
huawei(config)#mpls l2vpn
Enable the LDP function globally and enable the split horizon policy.
huawei(config)#mpls ldp
huawei(config-mpls-ldp)#outbound peer all split-horizon
huawei(config-mpls-ldp)#quit
Add VLAN 4001 for forwarding MPLS packets and add two upstream ports to it.
huawei(config)#vlan 4001 smart
huawei(config)#port vlan 4001 0/19/0
huawei(config)#port vlan 4001 0/19/1
Enable MPLS for VLAN 4001.
huawei(config)#mpls vlan 4001
Set the IP address of VLAN interface 4001 to 10.50.50.50/24 and enable MPLS LDP for
the VLAN interface.
huawei(config)#interface vlanif 4001
huawei(config-if-vlanif4001)#ip address 10.50.50.50 24
huawei(config-if-vlanif4001)#mpls
huawei(config-if-vlanif4001)#mpls ldp
huawei(config-if-vlanif4001)#quit
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6 Configuration Example of VPLS
497