Huawei SmartAX MA5603T Configuration Manual page 497

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
8.
9.
10. Bind the GEM port to an ONT T-CONT.
11. Create the mapping between the GEM port and the service stream.
12. Add the service port.
Step 11 Configure the subtending multicast service.
1.
2.
Step 12 Save the data.
huawei(config)#save
----End
Issue 01 (2014-04-30)
huawei(config-if-gpon-0/18)#tcont bind-profile 1 0 1 profile-id 10
Divide the ONT port VLAN.
huawei(config-if-gpon-0/18)#ont port vlan 1 0 eth 10 0
huawei(config-if-gpon-0/18)#ont port native-vlan 1 0 eth 0 vlan 1530
Configure the GEM port.
huawei(config-if-gpon-0/18)#gemport add 1 gemportid 150 eth
NOTE
In the actual application, if the ONT terminal does not support the priority queue scheduling, you can use
the CAR to limit the rate when binding the GEM port to the ONT T-CONT.
huawei(config-if-gpon-0/18)#ont gemport bind 1 0 150 1 priority-queue 3
huawei(config-if-gpon-0/18)#ont gemport mapping 1 0 150 vlan 1530
huawei(config-if-gpon-0/18)#quit
huawei(config)#service-port vlan 1530 gpon 0/18/0 gemport 150 multi-service
user-vlan 10 rx-cttr 5 tx-cttr 8
Configure the multicast service.
l Configure the native VLAN.
huawei(config)#interface giu 0/19
huawei(config-if-giu-0/19)#native-vlan 0 vlan 100
huawei(config-if-giu-0/19)#native-vlan 1 vlan 100
huawei(config-if-giu-0/19)#quit
l Enable the multicast proxy.
huawei(config)#multicast-vlan 100
huawei(config-mvlan100)#igmp mode proxy
Are you sure to change IGMP mode?(y/n)[n]:y
l Configure the program library.
huawei(config-mvlan100)#igmp program add name program1 ip 224.1.1.1
sourceip 10.10.10.10
huawei(config-mvlan100)#igmp program add name program2 ip 224.1.1.2
sourceip 10.10.10.10
huawei(config-mvlan100)#igmp program add name program3 ip 224.1.1.3
sourceip 10.10.10.10
huawei(config-mvlan100)#quit
Configure the subtending multicast.
l Specify the subtending ports.
huawei(config)#btv
huawei(config-btv)#igmp cascade-port 0/19/0
huawei(config-btv)#igmp cascade-port 0/19/1
huawei(config-btv)#igmp cascade-port 0/20/0
l Modify the subtending ports.
huawei(config-btv)#igmp cascade-port modify 0/19/0 static enable
huawei(config-btv)#igmp cascade-port modify 0/19/1 static enable
huawei(config-btv)#igmp cascade-port modify 0/20/0 static enable
huawei(config-btv)#quit
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5 Configuration Example of MSTP Subtending Network
472