Huawei SmartAX MA5603T Configuration Manual page 202

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
huawei(config)#vlan 20 smart
Step 2 Add an upstream port to the VLAN.
Upstream port 0/19/0 on the GIU board is added to VLAN 20.
huawei(config)#port vlan 20 0/19 0
Step 3 Configure the IP address of the Layer 3 interface.
The Layer 3 IP address is 192.168.1.100/24.
huawei(config)#interface vlanif 20
huawei(config-if-vlanif20)#ip address 192.168.1.100 255.255.255.0
huawei(config-if-vlanif20)#quit
Step 4 Add a DBA profile.
The DBA profile ID is 12, the DBA profile uses the default name DBA-profile_12, the bandwidth
type is type1 (fixed bandwidth), and the user rate is the fixed 10 Mbit/s bandwidth.
NOTE
huawei(config)#dba-profile add profile-id 12 type1 fix 10240
Step 5 Configure an MDU line profile.
The MDU line profile ID is 5, T-CONT 1 is bound with DBA profile 12, GEM port 0 is bound
to T-CONT 1, the service type is ETH, and the mapping mode is VLAN mapping.
huawei(config)#ont-lineprofile gpon profile-id 5
huawei(config-gpon-lineprofile-5)#tcont 1 dba-profile-id 12
huawei(config-gpon-lineprofile-5)#gem add 0 eth tcont 1
huawei(config-gpon-lineprofile-5)#gem mapping 0 0 vlan 20
huawei(config-gpon-lineprofile-5)#commit
huawei(config-gpon-lineprofile-5)#quit
Step 6 Add an MDU.
MDU 0 is connected to GPON port 0, the MDU authentication mode is the SN authentication,
the SN is 32303131B39FD641, the management protocol is SNMP, and MDU profile 5 is bound
to MDU 0.
NOTE
huawei(config)#interface gpon 0/2
huawei(config-if-gpon-0/2)#ont add 0 0 sn-auth 32303131B39FD641 snmp ont-
lineprofile-id 5
Step 7 Configure the management IP address of the MDU.
Issue 01 (2014-04-30)
l The bandwidth type and the attribute of the DBA profile must be compatible with the service to be
carried.
l The system supports five DBA profile types, namely, type1 (fixed bandwidth), type2 (assured
bandwidth), type3 (assured bandwidth+maximum bandwidth), type4 (maximum bandwidth), and type5
(fixed bandwidth+assured bandwidth+maximum bandwidth).
l By default, the system provides DBA profiles 1 to 9, each of which provides typical values for traffic
parameters. By default, T-CONT 0 is bound with DBA profile 1.
l The value of the bandwidth you input when adding the DBA profile rounds down to the nearest integer
multiple of 64. For example, if the input bandwidth value is 1022 kbit/s, the actual bandwidth is 960
kbit/s.
l You can run the display dba-profile command to query the information about the DBA profile.
You can add an MDU in the following two ways: confirming an auto-discovered MDU and adding an
MDU offline. Here, the method of adding an MDU offline is considered as an example.
You can also run the port ont-auto-find command to enable the function of auto-discovering an MDU,
and then run the ont confirm command to confirm the auto-discovered MDU.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1 Commissioning
177