Huawei SmartAX MA5603T Configuration Manual page 303

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
4.
5.
Step 6 Enable the IPoA-IPoE protocol conversion.
This step is to configure the IPoA MAC address pool. The start MAC address in the MAC address
pool is 0000-1111-1010, and the maximum number of the MAC addresses in the MAC address
pool is 300. The IPoA-IPoE protocol conversion is enabled, the default gateway is the same as
the IP address (192.168.1.20) of the upper-layer router, and the service encapsulation mode is
LLC-IPoA. The IP address of the modem is 192.168.1.1.
huawei(config)#mac-pool xpoa 0000-1111-1010 300
huawei(config)#ipoa enable
huawei(config)#ipoa default gateway 192.168.1.20
huawei(config)#encapsulation 0/2/0 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1
huawei(config)#encapsulation 0/3/1 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1
huawei(config)#encapsulation 0/4/1 vpi 1 vci 39 type ipoa llc srcIP 192.168.1.1
Step 7 Save the data.
huawei(config)#save
----End
Verification
l
l
l
Issue 01 (2014-04-30)
NOTE
l If no traffic profile in the system meets the service requirement, run the traffic table ip command to
configure a new traffic profile.
l On the MA5600T/MA5603T/MA5608T, the user access rate can be limited by either a traffic profile
or a VDSL line profile. When both profiles are configured, the user bandwidth adopts the minimum
value in the two profiles. In this example, the traffic profile is used to limit the user access rate.
Run the service-port command to create a service port. The index of the new service virtual
port is 3, the access port is port 0/4/1, traffic profile 5 meets the service requirement, and
the S-VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and
VCI of the peer modem. Assume that the management VPI and VCI of the modem are 1
and 39. To facilitate the maintenance of the service port, also configure the service port
description.
huawei(config)#service-port 3 vlan 50 vdsl mode atm 0/4/1 vpi 1 vci 39 inbound
traffic-table index 5 outbound
traffic-table index 5
huawei(config)#service-port desc 3 description MA5600T/MA5603T/MA5608THW/
Vlanid:50/vdsl/smart
Set the maximum number of MAC addresses that can be learned by the service port is 16.
This parameter is to limit the maximum number of the MAC addresses that can be learned
by one account, namely the maximum number of the PCs that can access the Internet
through one account.
huawei(config)#mac-address max-mac-count service-port 3 16
Step 1: Set the VPI/VCI of the modem to 1/39, encapsulation mode to llc-ipoa, and IP
address to 192.168.1.1.
Step 2: After the settings on the modem are completed, the network connection is
automatically set up and the user can access the Internet.
Step 3: When downloading files through FTP, you can open Task Manager in Windows
and click Networking to check the link rate. Calculate the Internet access rate by the
formula: Attainable Internet access rate = Computer NIC rate/48 x 53 x 8. The calculated
result approximates to the planned 2048 kbit/s.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3 Configuring the DSLAM Services
278