Huawei SmartAX MA5603T Configuration Manual page 281

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
3.
4.
5.
Step 5 In the VDSL access mode, follow this procedure.
In this example, the VDSL normal mode is used as an example.
1.
Issue 01 (2014-04-30)
huawei(config-if-shl-0/3)#activate 1 3
huawei(config-if-shl-0/3)#alarm-config 1 1
huawei(config-if-shl-0/3)#quit
Run the display traffic table command to query the existing traffic profiles in the system.
huawei(config)#display traffic table ip from-index 0
{ <cr>|to-index<K> }:
Command:
display traffic table ip from-index 0
---------------------------------------------------------------------------
TID CIR CBS
(kbps) (bytes)
---------------------------------------------------------------------------
0 1024 34768
1 2496 81872
2 512 18384
3 576 20432
4 64 4048
5 2048 67536
6 off off
---------------------------------------------------------------------------
Total Num : 7
According to service requirements, the user access rate is 2048 kbit/s. The query result
shows that traffic profile 5 (for inbound and outbound rate limitation) meets the
requirements.
NOTE
l If a matched traffic profile is not available in the system, run the traffic table ip command to configure
a new traffic profile.
l On the MA5600T/MA5603T/MA5608T, the user access rate can be limited by either a traffic profile
or an SHDSL line profile. When both profiles are configured, the smaller one of the two rates
configured in the profiles is adopted as the user bandwidth. In this example, the traffic profile is used
to limit the user access rate.
Run the service-port command to create a service port, adopt traffic profile 5, and set the
S-VLAN ID to 50. Set the SHDSL channel mode to PTM, and create service port 2 on
SHDSL port 0/3/1. To facilitate the maintenance of the service port, also configure the
service port description.
huawei(config)#service-port 2 vlan 50 shdsl mode ptm 0/3/1 inbound traffic-
table
index 5 outbound traffic-table index 5
huawei(config)#service-port desc 2 description Vlanid:50/shdsl/vpi:1vci:39/
stacking
Set the C-VLAN ID of the preset service port 2 to 10 for identifying the user. Configure
the important user packet with a higher priority so that the user packet can be processed
with precedence, and set the priority of the inner VLAN to 4.
huawei(config)#stacking label service-port 2 10
huawei(config)#stacking inner-priority service-port 2 4
Configure a VDSL profile. For details, see Configuring VDSL2 Templates and Profiles.
Assume that the VDSL profile ID is 3, downstream rate is 2048 kbit/s, channel mode is the
interleave mode, maximum downstream interleave delay is 8 ms, maximum upstream
interleave delay is 2 ms, SNR margin is 6 dB, minimum downstream INP is 4, and minimum
upstream INP is 2.
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
PIR PBS Pri Copy-policy
(kbps) (bytes)
2048 69536 6 -
4992 163744 6 -
1024 36768 0 -
1152 40864 2 -
128 8096 4 -
4096 135072 0 -
off off 0 -
3 Configuring the DSLAM Services
Pri-Policy
tag-pri
tag-pri
tag-pri
tag-pri
tag-pri
tag-pri
tag-pri
256