Huawei SmartAX MA5603T Configuration Manual page 504

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
5.
6.
7.
8.
9.
10. Bind the GEM port to an ONT T-CONT.
11. Create the mapping between the GEM port and the service stream.
12. Add the service port.
Step 10 Configure the POTS service.
1.
2.
3.
Issue 01 (2014-04-30)
Add an ONT.
NOTE
l You can add an ONT in two ways: run the ont add command to add an ONT offline or run the ont
confirm command to confirm an ONT that is in the auto-find state.
l You need to run the port ont-auto-find command in the GPON mode to enable the auto-find function
of the ONT.
huawei(config)#interface gpon 0/18
huawei(config-if-gpon-0/18)#ont add 1 sn-auth hwhw-10101010 profile-id 2
NOTE
In this example, the ONT uses the default capability set profile 2. You can run the ont-profile add
command to configure the capability set profile of the ONT based on your requirements.
Bind the alarm threshold profile.
huawei(config-if-gpon-0/18)#ont alarm-profile 1 0 profile-id 1
Bind the DBA profile.
huawei(config-if-gpon-0/18)#tcont bind-profile 1 0 1 profile-id 10
Divide the ONT port VLAN.
huawei(config-if-gpon-0/18)#ont port vlan 1 0 eth 10 0
huawei(config-if-gpon-0/18)#ont port native-vlan 1 0 eth 0 vlan 1530
Configure the GEM port.
huawei(config-if-gpon-0/18)#gemport add 1 gemportid 150 eth
NOTE
In the actual application, if the ONT terminal does not support the priority queue scheduling, you can use
the CAR to limit the rate when binding the GEM port to the ONT T-CONT.
huawei(config-if-gpon-0/18)#ont gemport bind 1 0 150 1 priority-queue 3
huawei(config-if-gpon-0/18)#ont gemport mapping 1 0 150 vlan 1530
huawei(config-if-gpon-0/18)#quit
huawei(config)#service-port vlan 1530 gpon 0/18/0 gemport 150 multi-service
user-vlan 10 rx-cttr 5 tx-cttr 8
Configure the upstream ports of the media stream and the signaling flow.
huawei(config)#vlan 1600 smart
huawei(config)#port vlan 1600 0/19 0
huawei(config)#interface vlanif 1600
huawei(config-if-vlanif1600)#ip address 10.176.6.33 24
huawei(config-if-vlanif1600)#quit
Configure the static route destined to the MGC.
NOTE
When the MGC and the MG are in the same network segment, you do not need to configure the static
route.
huawei(config)#ip route-static 10.30.80.0 255.255.255.0 10.176.6.62
Configure the media IP address pool and the signaling IP address pool.
huawei(config)#voip
huawei(config-voip)#ip address media 10.176.6.33 10.176.6.62
huawei(config-voip)#ip address signaling 10.176.6.33
huawei(config-voip)#quit
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5 Configuration Example of MSTP Subtending Network
479