Huawei SmartAX MA5603T Configuration Manual page 720

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
3.
4.
5.
Step 7 Configure an IP address for an ONT SIP user.
For ONT 1 and ONT 2, configure the IP address obtaining mode to the DHCP mode, set the
management VLAN to VLAN 20, and use default values for other parameters.
huawei(config)#interface gpon 0/1
huawei(config-if-gpon-0/1)#ont ipconfig 0 1 dhcp vlan 20
huawei(config-if-gpon-0/1)#ont ipconfig 0 2 dhcp vlan 20
Step 8 Configure SIP POTS users.
1.
2.
Issue 01 (2014-04-30)
Run the display ont-sipagent-profile command to query the existing SIP agent profile in
the system. If the existing SIP agent profile in the system does not meet the requirements,
run the ont-sipagent-profile add command to add an SIP agent profile.
Create SIP agent profile 2, set the IP address of the SIP server to 200.200.200.200, and use
default values for other parameters.
huawei(config)#ont-sipagent-profile add profile-id 2 proxy-server
200.200.200.200
Configure an SIP service data profile.
Run the display ont-siprightflag-profile command to query the existing SIP agent profile
in the system. If the existing SIP service data profile in the system does not meet the
requirements, run the ont-siprightflag-profile add command to add an SIP service data
profile.
In this example, the default SIP service data profile, namely SIP service data profile 1 is
used.
Configure a POTS port profile.
Run the display ont-pots-profile command to query the existing POTS port profile in the
system. If the existing POTS port profile in the system does not meet the requirements, run
the ont-pots-profile add command to add a POTS port profile.
In this example, the default POTS port profile, namely POTS port profile 1 is used.
Configure a digitmap profile.
Run the display ont-digitmap-profile command to query the existing digitmap profile in
the system. If the existing digitmap profile in the system does not meet the requirements,
run the ont-digitmap-profile add command to add a digitmap profile.
In this example, the default digitmap profile, namely digitmap profile 1 is used.
Add an SIP interface and apply an SIP agent profile to the interface.
For ONT 1 and ONT 2, set the MG ID to 1, apply SIP agent profile 2 to ONT 1 and ONT
2, and use default values for other parameters.
If parameters in an SIP agent profile are changed, the SIP agent profile must be reapplied
to the ONT so that the changed parameters can take effect.
huawei(config-if-gpon-0/1)#if-sip add 0 1 1 sipagent-profile profile-id 2
huawei(config-if-gpon-0/1)#if-sip add 0 2 1 sipagent-profile profile-id 2
Add POTS users.
For ONT 1 and ONT 2, set the MG ID to 1 (identical to the MG ID of the added SIP
interface), create two POTS users named huawei1 and huawei2, set passwords to user1 and
user2, set their phone numbers to 77730010 and 77730020 and use default values for other
parameters.
huawei(config-if-gpon-0/1)#sippstnuser add 0 1 1 mgid 1 username huawei1 telno
77730010
huawei(config-if-gpon-0/1)#sippstnuser add 0 2 1 mgid 1 username huawei2 telno
77730020
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9 FTTH Configuration
695