Huawei SmartAX MA5603T Configuration Manual page 300

SmartAX MA5600T/MA5603T/MA5608T Multi-service
Access Module
Commissioning and Configuration Guide
2.
3.
4.
Issue 01 (2014-04-30)
huawei(config)#adsl line-profile quickadd 3 snr 60 30 120 60 30 120
huawei(config)#adsl channel-profile quickadd 3 interleaved-delay 10 10 rate
1024
2048 3096 1024 2048
3096
huawei(config)#adsl line-template quickadd 3 line 3 channel1 3 60 70 channel2
3
Activate the ADSL port. The port is port 0/2/0, and ADSL line template 3 and the default
alarm template (alarm template 1) are bound to the port.
NOTE
By default, an ADSL port is in the activated state. Before binding a template to the port, you must deactivate
the port.
huawei(config)#interface adsl 0/2
huawei(config-if-adsl-0/2)#deactivate 0
huawei(config-if-adsl-0/2)#activate 0 template-index 3
huawei(config-if-adsl-0/2)#alarm-config 0 1
huawei(config-if-adsl-0/2)#quit
Run the display traffic table ip command to query the traffic profiles that exist in the
system.
huawei(config)#display traffic table ip from-index 0
{ <cr>|to-index<K> }:
Command:
display traffic table ip from-index 0
---------------------------------------------------------------------------
TID CIR CBS
(kbps) (bytes)
---------------------------------------------------------------------------
0 1024 34768
1 2496 81872
2 512 18384
3 576 20432
4 64 4048
5 2048 67536
6 off off
---------------------------------------------------------------------------
Total Num : 7
According to service requirement, the user access rate is 2048 kbit/s. The query result shows
that traffic profile 5 meets the requirement.
NOTE
l If no traffic profile in the system meets the service requirement, run the traffic table ip command to
configure a new traffic profile.
l On the MA5600T/MA5603T/MA5608T, the user access rate can be limited by either a traffic profile
or an ADSL line profile. When both profiles are configured, the user bandwidth adopts the minimum
value in the two profiles. In this example, the traffic profile is used to limit the user access rate.
Run the service-port command to create a service port. The index of the new service port
is 1, the access port is port 0/2/0, traffic profile 5 meets the service requirement, and the S-
VLAN is VLAN 50. The VPI and VCI must be the same as the management VPI and VCI
of the peer modem. Assume that the management VPI and VCI of the modem are 1 and
39. To facilitate the maintenance of the service port, also configure the service port
description.
huawei(config)#service-port 1 vlan 50 adsl 0/2/0 vpi 1 vci 39 inbound traffic-
table
index 5 outbound traffic-table index 5
huawei(config)#service-port desc 1 description MA5600T/MA5603T/MA5608THW/
Vlanid:50/adsl/smart
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
PIR PBS Pri Copy-policy
(kbps) (bytes)
2048 69536 6 -
4992 163744 6 -
1024 36768 0 -
1152 40864 2 -
128 8096 4 -
4096 135072 0 -
off off 0 -
3 Configuring the DSLAM Services
Pri-Policy
tag-pri
tag-pri
tag-pri
tag-pri
tag-pri
tag-pri
tag-pri
275