Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 751

SORTER> OPTION
TRY-OVER Set limit of stack capacity: Fin-A1
Lv.1 Details To set the limit of stack capacity for Z-fold paper and half hold paper.
("Stack over" is detected when the paper is stacked over the limit of
stack height.)
If the limit of stack capacity is removed, paper can be stacked
beyond the maximum stack capacity.
Use case When stacking the paper beyond the maximum stack capacity of
tray.
Adj/set/operate method 1) Enter the setting value and press OK.
2) Turn OFF/ON the main power switch.
Caution Tell users and get an agreement that when the high density paper is
stacked until the maximum volume, a tray may not be able to move
up.
Display/adj/set range 0 to 1
0: Normal operation, 1: Remove the stack limit
Default value 0
PUCH-SW High-prdctvty/-accurcy punch mode:Fin-A1
Lv.1 Details To switch the high-productivity punch mode or high-accuracy punch
mode of Finisher.
Use case When switching the high-productivity punch mode or high-accuracy
punch mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
ALG-IMPR Set Finisher alignment mode: Fin-A1
Lv.1 Details To set the special mode for improving the alignment condition.
Use case When using the special mode for improving the alignment condition
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 20
Appropriate target value 0
Default value 0
BUFF-SW2 Setting Finisher buffer operation:Fin-A1
Lv.1 Details To set ON/OFF of buffer operation in the Finisher.
When 1 is set, the alignment condition of the paper delivered from
the lower path may be improved, but productivity decreases.
Use case When misalignment occurs in the buffer paper delivered from the
lower path
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When the buffer operation is set to OFF, productivity decreases.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
SORTER> OPTION
1SHT-SRT Setting of 1-sheet Offset&Collate:Fin-A1
Lv.1 Details To set ON/OFF of Offset&Collate for 1-sheet document.
When 1 is set, Offset&Collate for 1-sheet document is enabled, but
the paper is not appropriately stacked.
Use case When preferring to execute 1-sheet Offset&Collate with low stacking
condition
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SD-LMTLS Set sddl delivery limitless oprtn:Fin-A1
Lv.1 Details To set ON/OFF of the Finisher Saddle Assembly limitless delivery
operation.
When 1 is set, "stack over" does not occur and saddle operation can
be performed continuously, but the stacking condition decreases.
Use case When preferring to perform saddle operation continuously
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When limitless operation is set to ON, the saddle stacking condition
decreases.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SD-STCNB Set sddl delivery stack quantity: Fin-A1
Lv.1 Details To increase the saddle stacking number.
When 1 is set, the "saddle stack over" count is increased, and the
stacking number increases.
Use case When preferring to increase the stacking number of the Saddle
Delivery Assembly
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Default value 0
BUFF-THK Set buffer oprtn for heavy paper: Fin-A1
Lv.1 Details To set ON/OFF of buffer operation for heavy paper (181 to 220g/m2).
When 1 is set, productivity of sort and staple mode of Finisher is
improved, but the stacking condition decreases.
Use case When improving productivity of sort and staple mode for heavy paper
(181 to 220g/m2)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When improving productivity, the stacking condition may decrease.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode SORTER> OPTION> PRD-PRTY
5
5-523