Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 743

SORTER> ADJUST
SDL-ALG Adj of Saddle Stitcher alignment width
Lv.1 Details To adjust the alignment width of Saddle Stitcher.
As the value is incremented by 1, the alignment width is increased
by mm.
+:
-:
Use case When the misalignment occurs within a paper stack on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-RLPT Adj Sddl Sttch Diseng Roll diseng amount
Lv.1 Details To adjust the disengagement amount of Saddle Stitcher
Disengagement Roller.
As the value is incremented by 1, the disengagement amount is
increased by mm.
+:
-:
Use case When the feed failure (with thin paper, etc.) occurs on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SDL-RLFD Adj Sddl Sttch Diseng Roller feed amount
Lv.1 Details To adjust the feed amount of Saddle Stitcher Disengagement Roller.
As the value is incremented by 1, the feed amount is increased by
mm.
+:
-:
Use case When the feed failure (with thin paper, etc.) occurs on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SORTER> ADJUST
SDL-RLHD Adj Sddl Sttch Diseng Roll fold position
Lv.1 Details To adjust the fold position of Saddle Stitcher Disengagement Roller.
As the value is incremented by 1, the fold position moves by mm.
+:
-:
Use case When the feed failure (with thin paper, etc.) occurs on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit mm
Default value 0
SBRL-MTR Adj Swback Roll Up/Down Motor HP:Fin-A1
Lv.1 Details To adjust the home position of Switchback Roller Upper/Lower Motor.
As the value is incremented by 1, the standby position of Switchback
Roller moves by 0.25mm
+: Decrease
-: Increase
When the value is inappropriate, it causes a misalignment of paper
stack in feed direction or missing pages.
Use case • When the distance between Accumulation Tray and Switchback
Roller is not 3 to 4mm
• When replacing the EEPROM
• When replacing the PCB
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -9 to 9
Unit 0.25 mm
Default value 0
BFR-UPA4 Adj Swng Roll rising tmg for A4: Fin-A1
Lv.1 Details To adjust the Swing Roller rise timing when A4 size paper is waited
in the buffer path.
As the value is incremented by 1, the rise timing becomes early by 1
msec.
Use case When misalignment occurs in A4 size buffer paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 50
Unit 1 msec
5
5-515