Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 509

COPIER> FUNCTION> INSTALL
STRD-POS Scan position auto adj in DADF mode
Lv.1 Details To adjust the DADF scanning position automatically.
Use case At DADF installation/uninstallation
Adj/set/operate method 1) Set a paper for stream reading position adjustment, and then close
the DADF.
2) Select the item, and then press OK key.
The operation automatically stops after the adjustment.
3) Write the value displayed by COPIER>ADJUST>ADJ-XY>STRD-
POS in the service label.
Caution Write the adjusted value in the service label.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Required time Approx. 10 seconds
Related service mode COPIER> ADJUST> ADJ-XY> STRD-POS
Supplement/memo For the details of paper for stream reading position adjustment, refer
to the Service Manual.
CARD Card number setting
Lv.1 Details To set the card number to be used for Card Reader.
A series of numbers from the entered number to the number of cards
specified by CARD-RNG can be used.
Use case • At installation of the Card Reader
• After replacement of the HDD
Adj/set/operate method 1) Enter the number, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The card management information (department ID and password) is
initialized.
Display/adj/set range 0 to 2001
Default value 0
Related service mode COPIER> OPTION> FNC-SW> CARD-RNG (Level 2)
KEY ON/OFF of management key function
Lv.1 Details To set whether to enable or disable the management key function.
Use case At installation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
COPIER> FUNCTION> INSTALL
INISET-Y Exe of Y Dev Ass'y initial install mode
Lv.1 Details To automatically execute operation necessary for initial installation of
the Y Developing Assembly.
1. Patch light intensity correction
2. Background correction
3. Potential control
4. Idle rotation of the Developing Assembly
5. Initialization of the Toner Density Sensor
6. Initialization of the Patch Sensor
7. Counter reset of the Developing Assembly
After execution, the AINR-OFF setting automatically returns to "0:
OFF".
Use case When replacing the Y Developing Assembly
Adj/set/operate method Select the item, and then press OK key.
Caution • When installing the machine or replacing the Developing Assembly
of other color, do not use this item. .
• Execute this item after setting "AINR-OFF" to "1: ON".
Display/adj/set range During operation: xxx second (remaining time), At normal termination:
OK, At abnormal termination: NG
Required time 155 seconds
Related service mode COPIER> FUNCTION> INSTALL> INISET-M, INISET-C, INISET-K,
INISET-4, AINR-OFF
INISET-M Exe of M Dev Ass'y initial install mode
Lv.1 Details To automatically execute operation necessary for initial installation of
the M Developing Assembly.
1. Patch light intensity correction
2. Background correction
3. Potential control
4. Idle rotation of the Developing Assembly
5. Initialization of the Toner Density Sensor
6. Initialization of the Patch Sensor
7. Counter reset of the Developing Assembly
After execution, the AINR-OFF setting automatically returns to "0:
OFF".
Use case When replacing the M Developing Assembly
Adj/set/operate method Select the item, and then press OK key.
Caution • When installing the machine or replacing the Developing Assembly
of other color, do not use this item. .
• Execute this item after setting "AINR-OFF" to "1: ON".
Display/adj/set range During operation: xxx second (remaining time), At normal termination:
OK, At abnormal termination: NG
Required time 155 seconds
Related service mode COPIER> FUNCTION> INSTALL> INISET-Y, INISET-C, INISET-K,
INISET-4, AINR-OFF
5
5-281