Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 521

■ PART-CHK
COPIER> FUNCTION> PART-CHK
CL Specification of operation Clutch
Lv.1 Details To specify the Transfer Cleaning Clutch (CL1) to operate.
Use case When replacing the Clutch/checking the operation
Adj/set/operate method Enter "1", and then press OK key.
Display/adj/set range 1 to 7
1: Deck Pickup Clutch (CL1)
2: Multi Deck (Upper) Pickup Clutch (CL2)
3: Multi Deck (Upper) Pullout Clutch (CL5)
4: Multi Deck (Middle) Pickup Clutch (CL3)
5: Multi Deck (Middle) Pullout Clutch (CL6)
6: Multi Deck (Lower) Pickup Clutch (CL4)
7: Multi Deck (Lower) Pullout Clutch (CL7)
During operation: ACTIVE, When operation finished normally: OK!
Default value 0
Related service mode COPIER> FUNCTION> PART-CHK> CL-ON
CL-ON Operation check of Clutch
Lv.1 Details To start operation check of the Transfer Cleaning Clutch (CL1).
During operation, ON/OFF is repeated with an interval of 3 seconds.
Use case When replacing the Clutch/checking the operation
Adj/set/operate method 1) Drive the ITB and Drum (COPIER> FUNCTION> MISC-P> MAIN-
DRV).
2) Select the item, and then press OK key.
3) Check the gear of the Transfer Cleaning Assembly.
Display/adj/set range During operation: ACTIVE, When operation finished normally: OK!
Default value 0
Required time Approx. 1 minute
Related service mode COPIER> FUNCTION> MISC-P> MAIN-DRV
COPIER> FUNCTION> PART-CHK> CL
Supplement/memo Remove the Inner Cover so that the Clutch can be checked visually.
COPIER> FUNCTION> PART-CHK
FAN Specification of operation Fan
Lv.1 Details To specify the Fan to operate.
Use case When replacing the Fan/checking the operation
Adj/set/operate method Enter the value, and then press OK key.
Display/adj/set range 1 to 23
1: Pre-fixing Feed Suction Fan (FM1)
2: Primary Charging Suction Fan (FM2)
3: Primary Charging Exhaust Fan (FM3)
4: Developing/Pre-transfer Charging Fan (FM4)
5: Color Cleaning Fan (FM5)
6: Fixing Heat Fan (FM6)
7: IH Power Supply Fan (FM7)
8: Power Supply Fan 1 (FM8)
9: Power Supply Fan (FM9)
10: Delivery Heat Fan 1 (FM10)
11: Delivery Heat Fan 2 (FM11)
12: Delivery Heat Fan 3 (FM12)
13: Delivery Heat Fan 4 (FM13)
14: Power Supply Cooling Fan (38V) (FM14)
15: Pressure Belt Cooling Fan (Front) (FM15)
16: Pressure Belt Cooling Fan (Rear) (FM16)
17: Hopper Cooling Fan (FM18)
18: Hopper Cooling Suction Fan (FM22)
19: Anti-adhesion Fan 1 (FM23)
20: Anti-adhesion Fan 2 (FM24)
21: Decurler Suction Fan (FM30)
22: Decurler Side Suction Fan (FM31)
23: Decurler Lower Exhaust Fan (FM32)
During operation: ACTIVE, When operation finished normally: OK!
Default value 1
Related service mode COPIER> FUNCTION> PART-CHK> FAN-ON
FAN-ON Operation check of Fan
Lv.1 Details To start operation check of the Fan specified by FAN.
Use case When replacing the Fan/checking the operation
Adj/set/operate method Select the item, and then press OK key.
Required time 1 minute
Related service mode COPIER> FUNCTION> PART-CHK> FAN
5
5-293