Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 619

COPIER> OPTION> USER
CPRT-DSP ON/OFF of [Print Charge Log] button
Lv.1 Details To set whether to display the [Print Charge Log] button to print the
charge logs on the charge log screen in user mode.
When "1: ON" is set, the button is displayed in Management
Settings> Charge Management> Charge Log Screen.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related user mode Management Settings > Charge Management > Charge Log
PCL-COPY Set of PCL COPIES command control method
Lv.2 Details To set the binder control method of COPIES command with PCL.
Select whether to use the control method of Canon-made PCL or
use the same control method of non-Canon-made PCL.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
0: Control method of Canon-made PCL (following the value of
COPIES command that is specified for each page to control on a
page basis)
1: Control method of non-Canon-made PCL (handling the value of
COPIES command, which is specified for page 1 at the time of
Collate mode, as bind figure while the value of COPIES command
for the next page or later is invalid. Same control applies as
Canon-made PCL at the time of Non Sorted mode)
2 to 65535: For future use
Default value 0
COPIER> OPTION> USER
CNT-SW Set default dis items on charge counter
Lv.1 Details To set default display items of the charge counter on the Counter
Check screen.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Do not use this mode overseas (outside Japan).
Display/adj/set range 0 to 1
0:
Counter 1 - Total 1: 101
Counter 2 - Total (Black 1): 108
Counter 3 - Copy (Full Color + Single Color/1): 232
Counter 4 - Print (Full Color + Single Color/1): 324
1:
Counter 1 - Total 2: 102
Counter 2 - Copy (Full Color + Single Color/2): 231
Counter 3 - Total A (Full Color + Single Color/2): 148
Counter 4 - Copy (Black 2): 222
Counter 5 - Total A (Black 2): 133
Default value 0
TAB-ACC Auto cassette change set for tab paper
Lv.1 Details To set to enable/disable auto cassette change when tab paper runs
out.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to instruct the user to thoroughly comply the following:
• Use tab paper with the same number of tabs
• Set tab paper
Be sure to comply the above; otherwise, proper print is not available
and it can cause soil inside the machine because of toner.
Display/adj/set range 0 to 1
0: Auto cassette change disabled, 1: Auto cassette change enabled
Default value 1
BCNT-AST Set of box print charge target job
Lv.1 Details To set the job type that advances the count in box print with NE
Controller (ASSIST).
Use case When switching the job type that is subject to counting of the box
print with NE Controller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: PDL job, 1: Copy job
Default value 0
5
5-391