Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 620

COPIER> OPTION> USER
PRJOB-CP Set count TX at RX/report print
Lv.2 Details To set to enable/disable a page-basis count pulse transmission to the
charging management device at the time of reception print or report
print.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No transmission, 1: Transmission
Default value 0
Supplement/memo Charging management device: Coin manager, Non-Canon-made
control card
DFLT-CPY Setting of color mode for copy
Lv.1 Details To set the default color mode for copy operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2: B/W
mode
Default value Europe: 2, Other than Europe: 0
Related user mode Function Settings> Copy> Select Color Settings for Copy> Use Auto
(Color/Black) Selection
DFLT-BOX Set of color mode for box print
Lv.1 Details To set the default color mode for box print operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
5
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2: B/W
mode
Default value Europe: 2, Other than Europe: 0
Related user mode Function Settings> Copy> Select Color Settings for Copy> Use Auto
(Color/Black) Selection
DOC-REM Dis/hide of original removal message
Lv.1 Details To set whether to display or hide the message to remove original
when scanning with DADF without opening/closing DADF after
scanning with the copyboard.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
5-392
COPIER> OPTION> USER
DPT-ID-7 Password entry set at dept ID reg/auth
Lv.2 Details To set whether to require a password entry at the time of registration/
authentication of department ID.
With the setting to require entry, entry of 7-digit password is required
as well as entry of department ID.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Department ID only, 1: 7-digit (password) entry
Default value 0
RUI-RJT Connct set at invalid auth from remoteUI
Lv.2 Details To set to disconnect HTTP port when the machine receives invalid
authentication from remote UI 3 times.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Continued connection, 1: Disconnected
Default value 0
SND-RATE Set compress ratio at SEND high compress
Lv.2 Details To set the compression ratio when the data compression ratio for
SEND (transmission) is set to "High Compression".
As the value is larger, the compression ratio is higher (the file size
becomes small).
Use case When making the transmission file size smaller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution As the value is too large, an image is deteriorated.
Display/adj/set range 0 to 2
0: Compression ratio 1/16, 1: Compression ratio 1/20, 2:
Compression ratio 1/24
Default value 0
Related user mode Function Settings > Send > Common Settings > Data Compression
Ratio