Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 747

SORTER> ADJUST
THC-PUSH Setting heavy ppr out prev mode:Fin-B1
Lv.1 Details Set 1 when the already stacked paper is pushed out at the time of
heavy paper delivery.
When 1 is set, the Stack Tray moves down temporarily before the
heavy paper is delivered to the Processing Tray if the leading sheet
is heavy paper.
Use case When the already stacked paper is pushed out at the time of heavy
paper delivery
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
OFST-STC Set poor offset stack prev mode:Fin-B1
Lv.1 Details Set 1 when paper is not appropriately stacked in the small-size offset
mode.
When 1 is set, buffer operation is not performed in the small-size
offset mode.
Use case When paper is not appropriately stacked in the small-size offset
mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
THN-STC Set poor thin ppr stack prev mode:Fin-B1
Lv.1 Details Set 1 when thin paper is not appropriately stacked.
When 1 is set, the stacking condition of thin paper improves.
Use case When thin paper is not appropriately stacked
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
STP-P-CH Set stpl stack displace prev mode:Fin-B1
Lv.1 Details Set 1 when the paper on the top is misaligned in the staple delivery
mode.
When 1 is set, paper stack alignment operation is executed twice
immediately before stapling.
Use case When the paper on the top is misaligned in the staple delivery mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SORTER> ADJUST
TRY-NIS Set tray switch noise reduct mode:Fin-B1
Lv.1 Details Set 1 when the operation noise after switching the Stack Tray is loud.
When 1 is set, the Stack Tray rise operation becomes slow.
Use case When the operation noise after switching the Stack Tray is loud
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
TRY-SU Set tray switching speedup mode: Fin-B1
Lv.1 Details Set 1 when the Stack Tray switching time is long.
When 1 is set, the Stack Tray rise speed becomes fast.
Use case When the Stack Tray switching time is long
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
FIN-NIS Set tray drive noise reduct mode: Fin-B1
Lv.1 Details Set 1 when the Finisher operation noise is loud.
When 1 is set, the initial Finisher operation is minimized.
Use case When the Finisher operation noise is loud
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
1SHT-SHF Set 1-sheet Offset+Collate: Fin-B1
Lv.1 Details Set 1 when setting Offset and Collate for 1-sheet document.
Use case When setting Offset and Collate for 1-sheet document
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SDL-SWCH Sddl stack capacity switch mode:Fin-B1
Lv.1 Details Set 1 when increasing the stacking capacity for saddle stitching.
When 1 is set, the stacking capacity increases over the upper limit.
Use case When increasing the stacking capacity for saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
SDL-ALM Set sddl full stack alarm mode: Fin-B1
Lv.1 Details Set 1 when disabling the stack full alarm for saddle stitching.
Use case When disabling the stack full alarm for saddle stitching
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
5
5-519