Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 517

COPIER> FUNCTION> DPC
DRMRSETK Forcible exe of Bk Drum replacement mode
Lv.1 Details When replacement of Drum is completed within 30 minutes, warm-
up rotation may not be executed at power-off/on because of high
fixing temperature. In such cases, drum potential becomes unstable,
causing an image failure to occur. To prevent this symptom, this
item forcibly executes the same operation as warm-up rotation. At
this time, laser power values, etc., that were corrected according to
Bk drum counter, total charging time, target Vd values for potential
control and drum durability are reset.
Use case • When detection of the Drum replacement has failed
• When the Drum used in other machine for a while is used as a
dummy unit
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
When the drum replacement mode is enabled, it becomes disabled
automatically after execution.
Caution Use a Drum that is not close to the end of life as a dummy unit.
When using a Drum that is close to the end of life, it affects the life of
developer, etc.
Display/adj/set range 0 to 1
0: Disabled (Not executed), 1: Enabled (Executed)
Required time Approx. 2 minutes
Related service mode COPIER> FUNCTION> DPC> DRM-RSET, DRMRSETY,
DRMRSETM, DRMRSETC
■ CST
MF-A4R
Lv.1 Details
Adj/set/operate method 1) Set A4R paper on the Multi-purpose Tray, and set the guide so
Caution
Related service mode
MF-A6R
Lv.1 Details
Adj/set/operate method 1) Set A6R paper on the Multi-purpose Tray, and set the guide so
Caution
Related service mode
MF-A4
T-5-49
Lv.1 Details
Adj/set/operate method 1) Set A4 paper on the Multi-purpose Tray, and set the guide so that
Caution
Related service mode
COPIER> FUNCTION> CST
Reg Multi-purpose Tray A4R stdrd width
To register the standard value of A4R paper width (210mm) on the
Multi-purpose Tray.
Make a fine adjustment by COPIER> ADJUST> CST-ADJ> MF-A4R.
that it fits the paper width.
2) Select the item, and then press OK key.
The value is registered after automatic adjustment.
After execution, check the registered value by COPIER> ADJUST>
CST-ADJ> MF-A4R, and write it down on the service label.
COPIER> ADJUST> CST-ADJ> MF-A4R
Reg Multi-purpose Tray A6R stdrd width
To register the standard value of A6R paper width (105 mm) on the
Multi-purpose Tray.
Make a fine adjustment by COPIER> ADJUST> CST-ADJ> MF-A6R.
that it fits the paper width.
2) Select the item, and then press OK key.
The value is registered after automatic adjustment.
After execution, check the registered value by COPIER> ADJUST>
CST-ADJ> MF-A6R, and write it down on the service label.
COPIER> ADJUST> CST-ADJ> MF-A6R
Reg Multi-purpose Tray A4 standard width
To register the standard value of A4 paper width (297 mm) on the
Multi-purpose Tray.
Make a fine adjustment by COPIER> ADJUST> CST-ADJ> MF-A4.
it fits the paper width.
2) Select the item, and then press OK key.
The value is registered after automatic adjustment.
After execution, check the registered value by COPIER> ADJUST>
CST-ADJ> MF-A4, and write it down on the service label.
COPIER> ADJUST> CST-ADJ> MF-A4
5
5-289