Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 105

E Detailed Occurance Items
code code area
E519 -8001 -05 Title Gear change home position error (Finisher-B1)
Description The gear change home position sensor does not turn
of detection OFF when the gear change motor has been driven for
387 pulses.
Measures 1. The gear change home position sensor (PI117) is
faulty.
2. The wiring between the finisher controller PCB and
gear change motor is faulty.
3. The gear change mechanism is faulty.
4. The gear change motor (M110) is faulty.
5. The finisher controller PCB is faulty.
E530 -8000 -05 Title Error in the front or rear alignment motor
Description The front or rear alignment motor operate abnormally
of detection during initialization.
Measures 1. The connector of the front/rear alignment HP sensor
(S108/S109) or the front/rear alignment motor (M108/
M109) are disconnected.
2. The wiring of the front/rear alignment HP sensor or the
front/rear alignment motor are faulty.
3. The front/rear alignment HP sensor is faulty.
4. The front/rear alignment motor is faulty.
5. The finisher controller PCB is faulty.
E530 -8001 -05 Title A. Error in the front alignment motor (Finisher-A1)
B. Front aligning plate home position error (Finisher-B1)
Description A. The front alignment plate does not come off the front
of detection alignment HP sensor when the front alignment motor
has been driven for 4 seconds.
B. The aligning plate does not leave the aligning plate
front home position sensor when the alignment plate
front motor has been driven for 4 seconds.
Measures A:
B:
Description
A-1. The connector of the front alignment HP sensor
(S108) or the front alignment motor (M108) are
disconnected.
A-2. The wiring of the front alignment HP sensor or
the front alignment motor are faulty.
A-3. The front alignment HP sensor is faulty.
A-4. The front alignment motor is faulty.
A-5. The finisher controller PCB is faulty.
B-1. The front aligning plate home position sensor
(PI106) is faulty.
B-2. The wiring between the finisher controller PCB
and front aligning plate motor is faulty.
B-3. The front aligning plate is faulty.
B-4. The front aligning plate motor (M103) is faulty.
B-5. The finisher controller PCB is faulty.
E Detailed Occurance Items
code code area
E530 -8002 -05 Title A. Error in the front alignment motor (Finisher-A1)
B. Front aligning plate home position error (Finisher-B1)
Description A. The front alignment HP sensor does not detect the
of detection front alignment plate when the front alignment motor
has been driven for 4 seconds.
B. The aligning plate does not return to aligning plate front
home position sensor when the alignment plate front
motor has been driven for 4 seconds.
Measures A:
B:
E531 -8001 -05 Title A. Error in the staple motor (Finisher-A1)
B. Staple home position error (Finisher-B1)
Description A. The staple unit does not come off the staple HP sensor
of detection when the staple motor has been driven for 0.4 second.
B. The stapler does not leave the staple home position
when the staple motor has been driven for 0.4 second.
Measures A:
B:
Description
A-1. The connector of the front alignment HP sensor
(S108) or the front alignment motor (M108) are
disconnected.
A-2. The wiring of the front alignment HP sensor or
the front alignment motor are faulty.
A-3. The front alignment HP sensor is faulty.
A-4. The front alignment motor is faulty.
A-5. The finisher controller PCB is faulty.
B-1. The front aligning plate home position sensor
(PI106) is faulty.
B-2. The wiring between the finisher controller PCB
and front aligning plate motor is faulty.
B-3. The front aligning plate is faulty.
B-4. The front aligning plate motor (M103) is faulty.
B-5. The finisher controller PCB is faulty.
A-1. The connector of the staple position switch
(SW103) is disconnected.
A-2. The wiring of the staple position switch is faulty.
A-3. The staple position switch is installation failure
or faulty.
A-4. The connector of the staple unit is
disconnected.
A-5. The wiring of the staple unit is faulty.
A-6. The staple unit is faulty.
A-7. The finisher controller PCB is faulty.
B-1. The wiring between the finisher controller PCB
and stapler is faulty.
B-2. The stapler is faulty.
B-3. The finisher controller PCB is faulty.
3
3-79