Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 556

COPIER> OPTION> FNC-SW
BASE-SW Model switch set from MEAP-Full to Base
Lv.1 Details To switch from the MEAP-Full model to the Base model.
Switch this mode in the case of restricting the operation of MEAP
application for trouble analysis.
Use case When trouble that caused by MEAP application occurs
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Switch from the Base model to the MEAP-Full model is not available.
Display/adj/set range 0 to 1
0: OFF (Base model), 1: ON (Full model)
Default value Depending on the setting of option bit (MeapModelBIT).
KSIZE-SW Set of Chinese paper (K-size) support
Lv.2 Details To set to detect/display the Chinese paper (K size paper: 8K, 16K).
Use case When using K size paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Go through the following: COPIER > OPTION > FNC-SW > MODEL-
SZ; and if MODEL-SZ is "0: AB configuration", this mode is enabled.
Display/adj/set range 0 to 1
0: Not supported, 1: Supported
Default value 0
Related service mode COPIER> OPTION> FNC-SW> MODEL-SZ
Supplement/memo 8K paper: 270 x 390 mm, 16K paper: 270 x 195 mm
ORG-A4R Special paper size set in DADF mode: A4R
Lv.2 Details To set the size of special paper (A4R) that cannot be recognized in
DADF stream reading mode.
When picking up A4R size original from the DADF of the Inch/AB
5
configuration models, the size is converted into the specified size so
that an image can be formed properly.
Use case • Upon user's request
• When picking up special paper size original from DADF
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: A4R, 1: FOLIO-R
Default value 0
PDF-RDCT PDF reduction set at forwarding
Lv.2 Details To set whether to reduce the image for transmission when converting
the image received by IFAX into PDF for e-mail/file transmission.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Following the current setting, 1: Image reduction
Default value 0
5-328
COPIER> OPTION> FNC-SW
REBOOTSW Restart setting at E240 error occurrence
Lv.2 Details To set whether to reboot in the case of E240 error.
In the case of E240 error, the machine is automatically rebooted due
to the possibility of continuous operation of the drive system while
the spooled print job is cleared.
Print job can be obtained if selecting the setting not to reboot.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution • Do not use this at the normal service.
• Be sure to get approval from the user by telling the possibility of
continuous operation of the drive system in the case of E240 error.
Display/adj/set range 0 to 1
0: Rebooted, 1: Not rebooted
Default value 0
Supplement/memo E240 error: Communication error between the Main Controller and
the DC Controller.
SJB-UNW Reserve upper limit of secure print job
Lv.2 Details To set the upper limit for the number of reserved jobs in secure print
job.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: 50 jobs, 1: 90 jobs
Default value 0
WEBV-SW ON/OFF of WebDAV function
Lv.2 Details To set ON/OFF of WebDAV function.
OFF setting can reduce memory use of the machine. In addition, the
following WebDAV-related items are hidden in user mode.
• Settings/Registration> Set Destination> Register
Destinations> Register New Dest.> File> Protocol> WebDAV
• Settings/Registration> Function Settings> Send> Common
Settings> Use Divided Chunk Send for WebDAV TX
Use case When reducing memory use of the machine
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
Related user mode Settings/Registration> Set Destination> Register Destinations>
Register New Dest.> File> Protocol> WebDAV
Settings/Registration> Function Settings> Send> Common Settings>
Use Divided Chunk Send for WebDAV TX
Supplement/memo WebDAV function is equipped as standard with the machine.