Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 638

COPIER> OPTION> ACC
DA-PUCT Set pickup/delivery comctn at DA charge
Lv.2 Details When a pickup and delivery notification error occurs due to network
failure, etc., the print operation might be done without charging.
This is to set the number of sheets that can be fed after the machine
receives Ack single from DA.
When the value is decreased, the number of prints to be made
without charging is decreased, but the productivity might be lowered.
When the value is increased, the productivity is not lowered, but the
number of prints to be made without charging is increased.
Caution As the smaller value is set, the number of prints to be made without
charging is decreased, but the productivity might be lowered.
Display/adj/set range 2 to 10
Default value 6
Supplement/memo DA: Digital Accessory
MIN-PRC Set of Coin Manager minimum price
Lv.1 Details To set the minimum amount to be handled with Coin Manager.
Enter 10 when specifying 10 Japanese yen as the minimum amount
to be handled with the Coin Manager that supports Japanese yen.
In the case to specify 1 to 4 (Euro/Pound/Swiss Franc/Dollar) by
going through the following: COPIER> OPTION> ACC > UNIT-PRC,
entry is in fractional unit. Entry of 50 indicates 50 cents ($ 0.50).
Use case At installation of Coin Manager
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This mode is enabled when selecting 4 for the following: COPIER >
OPTION > ACC > COIN.
Display/adj/set range 0 to 9999
5
Unit According to the setting value by the following: COPIER> OPTION>
ACC> UNIT-PRC.
Default value 10
Related service mode COPIER> OPTION> ACC> COIN, UNIT-PRC
Supplement/memo As for the charging amount, it causes an error if specifying the
value that is smaller than the minimum currency unit with Settings/
Registration mode.
5-410
COPIER> OPTION> ACC
MAX-PRC Set of Coin Manager maximum price
Lv.1 Details To set the maximum amount to be handled with Coin Manager.
Enter 8800 when specifying 8800 Japanese yen as the maximum
amount to be handled with the Coin Manager that supports Japanese
yen.
In the case to specify 1 to 4 (Euro/Pound/Swiss Franc/Dollar) by
going through the following: COPIER> OPTION> ACC> UNIT-PRC,
entry is in fractional unit. Entry of 50 indicates 50 cents ($ 0.50).
Use case At installation of Coin Manager
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution This mode is enabled when selecting 4 for the following: COPIER>
OPTION> ACC> COIN.
Display/adj/set range 0 to 9999
Unit According to the setting value by the following: COPIER> OPTION>
ACC> UNIT-PRC.
Default value 8800
Related service mode COPIER> OPTION> ACC> COIN, UNIT-PRC
Supplement/memo As for charging amount, it causes an error if specifying the value that
is larger than the maximum currency unit with Settings/Registration
mode.
MIC-TUN Manual adj of voice recognize microphone
Lv.1 Details To manually adjust the sound receiving level (sensitivity) of the
connected voice recognition microphone.
Microphone sensitivity is automatically tuned in user mode; however,
adjust it manually as needed.
Use case When the sensitivity of microphone is not improved by auto tuning
Display/adj/set range 0 to 255
Default value 128
Related user mode Preferences > Accessibility > Voice Navigation Settings > Tune
Microphone
SRL-SPSW Setting of Serial I/F Kit support
Lv.1 Details To set the support level of the Serial Interface Kit.
To keep processing performance of printer engine, select "1: Priority
on speed".
To correctly stop the output by the upper limit number of sheets,
select "2: Priority on upper limit number of sheets".
Use case At installation of Serial Interface Kit
Caution With priority on speed, output cannot be correctly stopped by the
upper limit number of sheets.
With priority on the upper limit number of sheets, processing
performance of the printer engine is decreased depending on pickup
location.
Display/adj/set range 0 to 2
0: No support, 1: Priority on speed, 2: Priority on upper limit number
of sheets
Default value 0