Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 41

E Detailed Occurance Items
code code area
E007 -0101 -05 Title Fixing belt home position detection error
Description Fixing belt home position detection error (Failure of the
of detection fixing belt HP sensor (PS69))
Measures 1. Check installation of the fixing belt displacement
2. Check if there is open circuit of the harness between
3. Faulty fixing belt HP sensor flag -> if the behavior is
4. Replace the fixing belt HP sensor (PS69)
5. Replace the fixing belt displacement control motor
6. Replace the fixing feed driver PCB
7. Replace the DC controller PCB
E007 -0102 -05 Title Pressure belt home position detection error
Description Pressure belt home position detection error (Failure of
of detection the pressure belt HP sensor (PS78))
Measures 1. Check installation of the pressure belt displacement
2. Check if there is open circuit of the harness between
3. Faulty pressure belt HP sensor flag -> if the behavior
4. Replace the pressure belt HP sensor (PS78)
5. Replace the pressure belt displacement control motor
6. Replace the fixing feed driver PCB
7. Replace the DC controller PCB
E007 -9901 -05 Title Fixing belt displacement failure (Full displacement of the
fixing belt or failure of the fixing belt position sensor)
Description Failure of the fixing belt position sensor (An impossible
of detection combination of sensor signals occurred.)
Measures 1. Check if there is open circuit of the harness between
2. Check if the installation of the fixing belt position
3. Faulty fixing belt position sensor 1, 2 -> replace the
4. Faulty fixing belt unit -> replace the fixing belt unit
Description
control drive -> correct to the right installation
procedure
the fixing belt displacement control drive unit and the
fixing feed driver PCB, or the connector is physically
removed -> if it is open circuit, replace the harness
not normal, replace it
(M46)
control drive -> correct to the right installation
procedure
the pressure belt displacement control drive unit
and the fixing feed driver PCB, or the connector is
physically removed -> if it is open circuit, replace
is not normal, replace it
(M49)
the fixing belt position sensor 1, 2 (PS71, 72) and the
fixing feed driver PCB, or the connector is physically
removed -> if it is open circuit, replace
sensor 1, 2 is inappropriate
sensor
E Detailed Occurance Items
code code area
E007 -9902 -05 Title Pressure belt displacement failure (Full displacement of
the pressure belt or failure of the pressure belt position
sensor)
Description Failure of the pressure belt position sensor (An
of detection impossible combination of sensor signals occurred.)
Measures 1. Faulty connection of the drawer connector -> clean
2. Faulty pressure belt position sensor 1, 2 (PS76,
3. Faulty drawer connector -> replace the fixing drawer
E008 -0001 -05 Title Pressure belt unit life detection error
Description The amount of fixing motor current reached the specified
of detection value due to torque-up of the pressure belt.
Measures 1. Confirm the current value is 80 (0.8 A) and below on
2. Clear the current value log of fixing motor on the
E008 -0002 -05 Title Fixing belt unit life detection error
Description Total rotation time of the fixing belt reached 15,000
of detection hours.
Measures The fixing belt unit reaches to its life -> replace the fixing
belt unit
E008 -0003 -05 Title Fixing belt unit life detection error
Description Page count for the fixing belt reached to the 400,000
of detection sheets.
Measures The fixing belt unit reaches to its life -> replace the fixing
belt unit
Description
the drawer connector
77), open circuit of the harness, or the connector is
physically removed -> connect the connector, replace
the sensor or replace teh pressure stay
cable
the service mode (COPIER> DISPLAY> FIXING> FX-
MTR8).
A. In case that the current value is "smaller than 80"
A-1. The pressure belt unit reaches to its life ->
replace the pressure belt unit
A-2. Faulty fixing unit drive gear -> replace the
gear
A-3. Fault fixing motor (M48)
B. In case that the current value is "80 and larger"
B-1. Faulty fixing unit drive gear -> replace the
gear
B-2. Faulty fixing motor (M48) -> replace the fixing
mtoor
B-3. Fault relay PCB -> replace it
service mode (COPIER> FUNCTION> CLEAR> FX-L-
CLR) after procedure.
3
3-15