Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 617

COPIER> OPTION> USER
MB-CCV Control card usage limit for Mail Box
Lv.2 Details To restrict use of control card for Mail Box.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Unlimited, 1: Limited
Default value 0
CONTROL Charge setting of PDL job
Lv.1 Details To set charge count transmission of PDL job to the connecting
charging management device (coin manager or non-Canon-made
control card).
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No charge, 1: Charge
Default value 0
B4-L-CNT Count setting of B4 size
Lv.1 Details To set B4 count with software counter 1 to 8 as to whether B4 is
counted as large size or small size.
Selecting 1 counts B4 or larger size paper as large size while paper
smaller than B4 size as small size.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Small size, 1: Large size
Default value 0
Related service mode COPIER> OPTION> FNC-SW> SC-L-CNT
MF-LG-ST Dis/hide of long strip mode
Lv.2 Details To set whether to display or hide the [Long Original] button.
When 1 is set, [Long Original] button is displayed in Copy > Options
screen and the long strip paper becomes available.
Use case Upon user's request. (use of long strip original or long strip paper)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
Related user mode Copy > Options
Supplement/memo Up to 630mm length paper is supported when DADF is used.
COPIER> OPTION> USER
CNT-DISP Display/hide of serial No.
Lv.2 Details To set whether to display or hide the serial No. on the Counter Check
screen.
Use case When setting to display/hide serial No. on the Counter Check screen.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Display, 1: Hide
Default value 0
COPY-JOB Setting of copy job reservation
Lv.1 Details To set to enable/disable copy job reservation when the Card Reader/
Coin Manager is used.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Enabled, 1: Disabled
Default value 0
OP-SZ-DT ON/OFF original size dtct:Cpybrd open
Lv.2 Details To set ON/OFF of original size detection function in the state which
the Copyboard is opened.
When setting to 0 (OFF), enter the original size on the Control Panel
manually.
When setting to 1 (ON), the original size is automatically detected.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
NW-SCAN Setting of network scan function usage
Lv.2 Details To set to enable/disable use of network scan function.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution • Do not use this mode in Japan.
• For PS/PCL machines for overseas (outside Japan), fix the setting
value as 1. For others, permit the use.
Display/adj/set range 0 to 1
0: Disabled, 1: Enabled
5
5-389