Canon imageRUNNER ADVANCE 9070 PRO series Service Manual Digest page 563

COPIER> OPTION> DSPLY-SW
T-LW-LVL Dis timing of toner level warning mssg
Lv.2 Details To set the warning message display timing (indicate the remaining
toner in Toner Container using "%").
When the residual toner level becomes lower than the threshold, a
warning message of "Toner is low. Replacement not yet needed." is
displayed on the Control Panel.
When the value is incremented by 1, the threshold is increased by
1%. As the bigger value is set, the message timing to be displayed
becomes earlier.
Use case • Upon user's request
• At the timing that the service engineer visits to the customer, etc.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 5 to 100
Unit 1%
Default value Europe: 5, Other than Europe: 10 (iR-ADV C9074 PRO/9070 PRO
for Japan only: 20)
Related service mode COPIER> OPTION> DSPLY-SW> TNR-WARN
NWERR-SW OFF/ON of network-related error display
Lv.2 Details To set OFF/ON of network-related error message display.
When setting "0: OFF" while the machine is not connected to
network, the error message "Check the network connection." is not
displayed.
Use case When using the machine as a copy machine
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1: Normal model, 0: Self-copy model
UISW-DSP ON/OFF of user screen switch display
Lv.2 Details To set ON/OFF of the switch to change the standard screen and
simple screen for the users.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
T-CRG-SW ON/OFF of Toner Cntner rplce user mode
Lv.2 Details To set whether to display or hide the Toner Container replacement
screen in user mode.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Required time Adjustment/Maintenance> Maintenance> Replace Specified Toner
COPIER> OPTION> DSPLY-SW
FXMSG-SW ON/OFF of Fixing Ass'y rplce warning dis
Lv.2 Details To set whether to display the warning prompting to replace the Fixing
Assembly on the Control Panel when the Fixing Assembly reaches
its life.
Criteria for judging the life differ, depending on the setting value of
FXMSGSW2.
FXMSGSW2 = 0: Fixing Assembly Motor current value + Fixing Belt
Unit rotation time
FXMSGSW2 = 1: Items above + Total number of sheets fed on
Fixing Belt Unit
Factor at warning occurrence is identified in accordance with CODE
column of log displayed in COPIER> DISPLAY> ALARM-2.
• 06-0004: Current value of the Fixing Assembly Motor (FX-
MTR2 to 8)
• No log: Rotation time of the Fixing Belt Unit (FX-U-TM1)
• 06-0002: Total number of sheets fed on Fixing Belt Unit (FX-
BLT-U)
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Related service mode COPIER> OPTION> DSPLY-SW> FXMSGSW2
COPIER> DISPLAY> ALARM-2
COPIER> DISPLAY> FIXING>FX-MTR2 to 8, FX-U-TM1
COPIER> COUNTER> DRBL-1> FX-BLT-U
MEAP-DSP Screen switch set from MEAP to standard
Lv.2 Details To set to enable/disable switching from MEAP screen to the standard
screen (COPY/SEND/Mail Box screen, etc). (Setting to display/hide
the arrow mark on MEAP screen)
In the case of an error/jam/alarm, the screen is switched to the
standard screen to display warning even if disabling this mode.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Enabled, 1: Disabled
Default value 0
Related service mode COPIER> OPTION> DSPLY-SW> ANIM-SW
Supplement/memo If disabling the switch with ANIM-SW, the screen will not be switched
to the standard screen even in the case of an error/jam/alarm.
5
5-335