Table of Contents
Advertisement
debug cr10k-rp
Jun 19 13:07:32.316: RPTX to Cobalt: 0x801B634, size=111
006F0000 00057010 422B2488 00020000 10000006 10000010 950701DB 00016440
D1420800 4500004B 2B260000 FF11187A A4789781 A478978F CD7E00A1 0037D2CA
302D0201 00040670 75626C69 63A02002 03062B27 02010002 01003013 3011060D
....
Jun 19 13:07:32.316: RPTX: Using Downstream Service Flow ID : 16939, SID : 2
Jun 19 13:07:32.316: RPTX to Cobalt: 0x8023834, size=111
006F0000 00057010 422B2488 00020000 10000006 10000010 950701DB 00016440
D1420800 4500004B 2B270000 FF111879 A4789781 A478978F CD7E00A1 0037D2CB
302D0201 00040670 75626C69 63A02002 03062B28 02010002 01003013 3011060D
....
Table 5-6
Table 5-6
Field
RPIX: Using Downstream
Service Flow ID
SID
RPTX or RPRX
Size
Packet Dump
The following example shows typical output for SID debugging messages:
Router# debug cr10k-rp sid
CR10K RP debug SID debugging is on
(Cable 6/1/0:2): CM Offline - MAC 00C0.1234.5678, SID 113
(Cable 6/1/0:2): -Shutdown CM- SID 231
(Cable 6/1/0:2): CM Shutdown - MAC 00C0.2210.a01c, SID 231
(Cable 6/1/0:2): CM Remove - MAC 00C0.2210.a01c, SID 231
Call SID replace with old IP addr 10.10.13.18 new IP addr 10.10.13.121
(Cable 5/1/1:1) - New CM 00C0.1122.bcab, SID 396
(Cable 5/1/0:1) - New CM 00C0.8723.11F0, SID 397
(Cable 5/1/0:1) - CM Init FAILED - MAC 00C0.8723.11F0, SID 397
The following example shows typical output for spectrum management debugging messages for a
particular interface:
Router# debug cable interface c6/1/0 sid 2
Router# debug cr10k-rp pkt spec
CR10K RP debug Spectrum debugging is on
(Cable 5/0/0:4) Release frequency (11600000, 3200000) from group 12
(Cable 5/0/0:4) Frequency request (10000000 - 13200000) from group 12 approved
(Cable 7/0/0:1) Frequency request (12000000 - 13600000) from group 2 approved
(Cable 7/0/0:1) Release frequency (12800000, 1600000) from group 2
(Cable 7/0/0:1) Frequency request (12000000 - 15200000) from group 2 approved
(Cable 7/0/0:2) Frequency request (20000000 - 21600000) from group 22 approved
(Cable 7/0/0:2) Release frequency (20800000, 1600000) from group 22
Cisco Broadband Cable Command Reference Guide
5-94
explains the information contained in the display for each packet:
debug cr10k-rp pkt Field Descriptions
Description
Displays the service flow ID (SFID) for this packet.
Displays the service ID (SID) for this packet.
Displays whether this packet is transmitted (RPTX) or received
(RPRX) by the processor.
Displays the size of the packet's datagram in decimal.
Displays the first 96 bytes of the packet's datagram in hexadecimal.
The command then displays an ellipses (. . .) if the datagram is larger
than 96 bytes.
Chapter 5
Cisco CMTS Debugging Commands
V5
OL-1581-08
Advertisement
Table of Contents
