ABB +N5600 Firmware Instructions page 449

No. Name/Value
85.34 Upthrust head 3
85.35 Upthrust flowrate 3
85.36 DNT zone 50%
Head 3
85.37 UPT zone 50%
Head 3
85.38 Workzone 1/3 Head
3
85.39 Workzone 2/3 Head
3
85.40 Head at 0 flowrate 4
85.41 Flowrate max 4
85.42 Downthrust head 4
85.43 Downthrust flowrate
4
85.44 Upthrust head 4
85.45 Upthrust flowrate 4
85.46 DNT zone 50%
Head 4
85.47 UPT zone 50%
Head 4
85.48 Workzone 1/3 Head
4
85.49 Workzone 2/3 Head
4
85.50 Head at 0 flowrate 5
85.51 Flowrate max 5
85.52 Downthrust head 5
85.53 Downthrust flowrate
5
85.54 Upthrust head 5
85.55 Upthrust flowrate 5
85.56 DNT zone 50%
Head 5
85.57 UPT zone 50%
Head 5
85.58 Workzone 1/3 Head
5
85.59 Workzone 2/3 Head
5
85.60 Curve fine tune
enable
Not selected
Selected
DI1
Description
See parameter 85.14 Upthrust head 1
See parameter 85.15 Upthrust flowrate 1
See parameter 85.16 DNT zone 50% Head 1
See parameter 85.17 UPT zone 50% Head 1
See parameter 85.18 Workzone 1/3 Head 1
See parameter 85.19 Workzone 2/3 Head 1
See parameter 85.10 Head at 0 flowrate 1
See parameter 85.11 Flowrate max 1
See parameter 85.12 Downthrust head 1
See parameter 85.13 Downthrust flowrate 1
See parameter 85.14 Upthrust head 1
See parameter 85.15 Upthrust flowrate 1
See parameter 85.16 DNT zone 50% Head 1
See parameter 85.17 UPT zone 50% Head 1
See parameter 85.18 Workzone 1/3 Head 1
See parameter 85.19 Workzone 2/3 Head 1
See parameter 85.10 Head at 0 flowrate 1
See parameter 85.11 Flowrate max 1
See parameter 85.12 Downthrust head 1
See parameter 85.13 Downthrust flowrate 1
See parameter 85.14 Upthrust head 1
See parameter 85.15 Upthrust flowrate 1
See parameter 85.16 DNT zone 50% Head 1
See parameter 85.17 UPT zone 50% Head 1
See parameter 85.18 Workzone 1/3 Head 1
See parameter 85.19 Workzone 2/3 Head 1
Defines the source for the curve fine tune enable signal.
When the function is active, the user can adjust the actual
curvature for each of seven segments of the defined pump
curves with parameters 85.61...85.67.
Curve fine tune enable function is not selected.
Curve fine tune enable function is selected.
Digital input DI1 (10.02 DI delayed
Parameters 449
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 447).
(page 447).
(page 447).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 447).
(page 447).
(page 447).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
(page 448).
status, bit 0).
Def/FbEq16
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
0.00
Not selected
0
1
2