Table of Contents
Advertisement
Appendix 2.15 Operation Messages on Setting Display Unit
If a setting operation error occurs only any of the setting and display unit's screens, the error No. Exx and a message
indicating the details will appear.
Appendix 2.15.1 Operation Errors
Δ: Message requiring resetting and restarting
×: Message requiring restarting after canceling error conditions
(The bold characters are the messages displayed on the screen.)
Error No.
Error message
E01
SETTING ERROR
E02
DATA OVER
E03
No. NOT FOUND
E04
DEV. NOT READY
E05
NOT ACCEPTABLE
Appendix 2.15 Operation Messages on Setting Display Unit
- The setting data is incorrect. An alphabetic character was set when only number
can be set‚ etc.
- Data was input without setting number (#).
(Word editing)
- Even though no retrieval data was set, menu key "Word ↓ "
/"Word ↑ ", or "STR. ↓ "/"STR. ↑ " was pressed.
- Even though no data is stored in edit buffers, menu key "Replace" was pressed.
- One of the following characters was entered as the first character of the retrieval
Δ
data and edit buffers: 0 to 9, ".", " " (space), "+", "−", "=", "*", "[", and "]".
- When the incremental detection system was used, the parameter (#0 INIT SET)
was set on the absolute position setting screen.
- The data input for the standard parameter setting or during execution of formatting
is not "Y" or "N".
- A value from 4 to 10 was specified for "#1043 lang".
- Even though no language data exists, its output and comparison were attempted.
Check the numbers (O253 and O254) of the language data to be output.
- The setting data exceeded the setting range.
- The compensation data specification exceeded the range when inputting the tool
offset data on tape‚ so that block could not be input. Press the INPUT key again while
the input screen is displayed‚ and the input will continue from the next block.
Δ
- When work coordinate offsets are measured, the calculation results given by
pressing the CALC key are exceeding the specified range. Correctly specify the tool
length or the abrasion data of cutting edges used for the calculation.
- When there was no option, 2 or more was specified for "#1043 lang". Otherwise, an
option was added and 16 or more was specified for "#1043 lang".
- The corresponding setting No. (#) was not found. This error occurs if a setting No.
not found on the screen was set and input‚ or if a variable No. not found in the
specifications was set and input for the common variables.
Δ
- When the tool length was measured manually, a nonexisting tool wear
compensation number was specified and the sensor was turned on. Specify the R
register of the offset number correctly.
- The input/output u/nit power is not ON.
×
- The cable is disconnected.
- Setting of the transfer speed (baud rate) does not agree.
- The PLC timer cannot be set from the screen when the program is valid. (When
machine parameter bit selection #6449 bit 1 is set to 1.)
- The PLC counter cannot be set from the screen when the program is valid. (When
machine parameter bit selection #6449 bit 0 is set to 1.)
- The tool registration data setting is prohibited.
- Setting from the tool life management screen is prohibited.
- Absolute position setting screen' s "#1 ORIGIN" and "#2 Zero" cannot be set when
"#0 INIT SET" is invalid.
- The INPUT key was pressed to perform search for the program that is in
×
background edit status on the word edit screen.
- The menu keys (Replace and Insert) on the word edit screen were manipulated
when a running program is displayed (PDISP signal: ON).
- An attempt was made to set MDI data in an MDI setting lock state (the MDI setting
lock parameter is specified with 0 and a non-MDI mode is valid).
- Language data in display selection status was entered. Change the display
selection status once before entering the data. (#1043 lang)
- When the manual value command protection (#1228 aux12 /bit7) function is valid,
the manual command operation (M, S, and T keys) is performed in POSITION
screen.
C70 Setup Manual
Details
543
Advertisement
Table of Contents
Troubleshooting
