Table Of Contents - Mitsubishi Electric C70 Setup Manual

1 Outline........................................................................................................................................................... 1
1.1 Hardware and Device Configuration ..................................................................................................................... 2
1.2 Flow of the Initial Setup ......................................................................................................................................... 3
2 GOT Initial Setup ......................................................................................................................................... 5
2.1 GT Designer3........................................................................................................................................................... 6
2.1.1 Installing GT Designer3 ................................................................................................................................ 6
2.1.2 Making Communication Settings.................................................................................................................. 7
2.1.2.1 Setting Ethernet Connection (for GT16) .............................................................................................. 7
2.1.2.2 Setting Ethernet Connection (for GT15) ............................................................................................ 11
2.1.2.3 Setting a bus connection .................................................................................................................... 15
2.1.3 Setting the Saving Destination Drive for Backup Data ............................................................................ 18
2.1.4 Creating a GOT screen ................................................................................................................................ 20
2.1.4.1 Precautions for Device Settings......................................................................................................... 20
2.1.4.2 Special Function Switch ..................................................................................................................... 21
2.1.5 Transferring the Data to GOT (Using an USB cable)................................................................................. 22
2.1.5.1 Installing OS on GOT........................................................................................................................... 22
2.1.5.2 Transferring the Project Data to GOT ................................................................................................ 25
2.1.6 Transferring the Data to GOT (Using a CF card) ....................................................................................... 26
2.1.6.1 Writing the Data into a CF card .......................................................................................................... 26
2.1.6.2 OS Installation and Project Data Transfer from the CF Card to GOT ............................................. 28
2.2 GT Designer2 ........................................................................................................................................................ 29
2.2.1 Installing GT Designer2 .............................................................................................................................. 29
2.2.2 Making Communication Settings................................................................................................................ 30
2.2.2.1 Setting Ethernet Connection (for GT16) ............................................................................................ 30
2.2.2.2 Setting Ethernet Connection (for GT15) ............................................................................................ 34
2.2.2.3 Setting a bus connection .................................................................................................................... 42
2.2.3 Setting the Saving Destination Drive for Backup Data ............................................................................ 45
2.2.4 Creating a GOT screen ................................................................................................................................ 47
2.2.4.1 Precautions for Device Settings......................................................................................................... 47
2.2.4.2 Special Function Switch ..................................................................................................................... 48
2.2.5 Transferring the Data to GOT (Using an USB cable)................................................................................. 49
2.2.5.1 Installing OS on GOT........................................................................................................................... 49
2.2.5.2 Transferring the Project Data to GOT ................................................................................................ 52
2.2.6 Transferring the Data to GOT (Using a CF card) ....................................................................................... 53
2.2.6.1 Writing the Data into a CF card .......................................................................................................... 53
2.2.6.2 OS Installation and Project Data Transfer from the CF Card to GOT ............................................. 55
3 PLC CPU Initial Setup ................................................................................................................................ 57
3.1 GX Works2 ............................................................................................................................................................. 58
3.1.1 Connecting the Devices Necessary for Setup ........................................................................................... 58
3.1.2 Setting the Connection to GX Works2........................................................................................................ 59
3.1.3 Setting Multi-CPU Parameters .................................................................................................................... 61
3.1.4 Parameter Settings for Safety Observation ............................................................................................... 62
3.1.5 Writing Parameters ...................................................................................................................................... 65
3.2 GX Developer......................................................................................................................................................... 66
3.2.1 Connecting the Devices Necessary for Setup ........................................................................................... 66
3.2.2 Setting the Connection to GX Developer ................................................................................................... 67
3.2.3 Setting Multi-CPU Parameters .................................................................................................................... 69
3.2.4 Parameter Settings for Safety Observation ............................................................................................... 70
3.2.5 Writing Parameters ...................................................................................................................................... 73
4 CNC CPU Initial Setup ............................................................................................................................... 75
4.1 Connecting Battery to CNC CPU ......................................................................................................................... 76
4.2 Initializing CNC CPU Internal Data (Clearing SRAM Data) ................................................................................ 77
4.2.1 Types of Memory and Backup Data............................................................................................................ 78
4.2.1.1 Loss and Restoration of Absolute Position Data ............................................................................. 79
4.2.1.2 List of Standard Parameters............................................................................................................... 81
4.3 Setting Multi-CPU Parameters ............................................................................................................................. 82
4.4 Setting the Date and Time .................................................................................................................................... 86
4.5 Formatting File System (Memory Area) .............................................................................................................. 87
CONTENTS