Mitsubishi Electric C70 Setup Manual page 563

MITSUBISHI CNC
Appendix 2 Explanation of Alarms
Error No. Error message
E86 INPUT DATA ERR
E87 NOT EDIT PROG.
E88
CAN'T ADD BLOCK
E91 MODE ERROR (PBK)
E98
CAN'T RESEARCH
E110 ATA NOT READY
E111 FILE DUPLICATE
E112 ATA I/F ERROR
E113 MEMORY OVER
E114 CAN'T ERASE
E115 FILE NOT FOUND
E117 DIR NOT FOUND
E190 FORE EDITING
E191 NOT COM. SEARCH
E200 ADJUST ERROR
E201 UNIT NOT EQUIP
E301 CONNECT ERROR
E302 LOGIN ERROR
E311 DOWNLOAD ERR
E312 UPLOAD ERROR
E313 NO FILE
E314 FILE DUPLICATE
E315 FILE WRITE ERR
E316 FILE READ ERR
546
- When inputting the tool offset data‚ the data format was not correct‚ so that block
could not be input.
× If the input key is pressed again in the input screen‚ the input will continue from the
next block.
- When data is read from parameter tape, its format is incorrect.
- Playback edit was executed for a fixed cycle subprogram.
×
Playback edit of a fixed cycle subprogram is not possible.
- Playback edit cannot be executed unless the block being edited with playback is
displayed to the end (EOB) on the left side of the machining program display area.
×
Press the cursor key [ ↓ ]‚ and display the whole block to the end. Then‚ input the
data.
- G90 was set when "PLAYBACK G90" was off.
×
- G91 was set when "PLAYBACK G90" was on.
- In program restart for multi-part system, while a restart search is running in one part
system, another restart search was attempted in another part system. To start over
×
a search, cancel either one of the previous searches by resetting, and then search
again.
- ATA not mounted error when that appears when ATA Card screen is opened
Δ
Mount the ATA card.
- The name of the file to be output was found in the ATA card.
Δ
- New file name to be renamed already exists.
- The designated file is damaged or the ATA card is damaged.
×
Designate another file or replace the ATA card.
- The ATA card capacity was filled when outputting to the ATA card.
×
Delete files from the ATA card, or use another ATA card and output the data again.
- A directory containing subdirectories or files was required to be deleted.
×
Delete the file and all subdirectories before deleting the directory.
- The file to be input, compared, deleted or renamed was not found in the ATA card.
Δ
Designate a file saved in the ATA card.
- The set directory was not found on the disk.
× Check whether an intermediate directory was designated when designating an
absolute path.
- An attempt was made to perform background search for the program that is in
×
foreground search status. (Word editing)
× - Operation search was attempted in the tape mode.
- The hardware status can't be read correctly‚ so automatic adjustment was not
possible.
- Check the remote l/O unit.
×
- A Z55 RIO NOT CONNECT error occurred.
- Adjust manually.
- Unit defect (replace unit)
- The analog output unit is not mounted.
- Confirm the remote l/O unit.
× - Prepare a unit having analog output.
- Check the connection (power and signal wires)
- Unit defect (replace unit)
- The socket connection failed during Ethernet communication.
×
- If the host address is illegal or the port No. is incorrect, set correctly.
- Log in failed during Ethernet communication.
×
- Check the user name and password.
× - Reading of a file on the host side failed during Ethernet communication.
× - Writing of a file on the host side failed during Ethernet communication.
- The file designated with the host reception (host → IC) operation was not found on
the host side during Ethernet communication.
×
- The file designated with the host transmission (IC → host) operation was not found
in the IC card during Ethernet communication.
- The file name to be registered with the host reception (host → IC) operation was
found in the IC card during Ethernet communication.
×
- The file name to be registered with the host transmission (IC → host) operation was
found in the host during Ethernet communication.
× - Writing to the IC card failed during Ethernet communication.
× - Reading of an IC cared file failed during Ethernet communication.
Details