Mitsubishi Electric C70 Setup Manual page 561

MITSUBISHI CNC
Appendix 2 Explanation of Alarms
Error No. Error message
E06 NO SPEC
E07 RESET END
E08 PHYSICAL ERR
E09 TIME OUT
E10 MEMORY OVER
E11 PROG. No. DUPLI
E12 FILE ENTRY OVER
E13 NB NOT FOUND
E14 PROG. NOT FOUND
E15 EDIT LOCK B
E16 EDIT LOCK C
E17 PARITY H ERR
E18 PARITY V ERR
E20 OVER RUN ERR
E21 PROGRAM RUNNING
E22 CODE CHANGE ERR
E24 PLC RUN
E25 DATA MEMORY ERR
E26 NO CHARACTERS
E35 COMPARE ERROR
544
- The menu key for a function not in the specifications was pressed.
× - A parameter not in the specifications was set.
- A language that was not added as an option was selected. (#1043 lang)
Δ - The input/output operations were forcibly stopped by reset‚ etc. (including EMG).
× - The input/output parameter setting or input/output unit side setting was incorrect.
- The input/output unit parameter "TIME-OUT TIME" setting was too short.
×
- There is no EOB code in the machining program.
- The program cannot be written because the memory capacity is exceeded.
This error occurs when the MDI data setting on the MDI screen exceeds 500
×
characters‚ or when saving MDl‚ editing or making a program on the edit screen‚ input
on the data input/output screen‚ program copy‚ etc.
- When registering a machining program in the memory‚ a program with the same
No. as the designated program No. was found in the memory. Refer to the program
Δ file to find a program No. not being used‚ and reset the program No.
This error occurs during MDI registration in the MDI screen or during creation of a
program in the edit screen.
- When registering a machining program in the memory‚ the No. of programs
determined in the specifications is exceeded‚ preventing registration.
×
This error occurs during MDI registration in the MDI screen‚ creation of a program in
the edit screen‚ data input in the data input/output screen‚ and program copy.
- The block with the designated sequence No. or block No. does not exist in the
Δ
designated program.
- The designated program is not found in the memory.
Δ - The corresponding program No. was not found with search of tape memory during
graphic check.
- An operation (edit‚ input/output‚ buffer correction‚ etc.) inhibited for machining
×
program B and C was attempted.
- An operation (edit‚ input/output‚ buffer correction‚ etc.) inhibited for machining
×
program B was attempted.
- A parity H error was detected during data input‚ etc.
× Check the paper tape or input device. This error may occur if the paper tape is dirtied
with oil‚ etc.
- A parity V error was detected during data input. Check the paper tape to see
whether the number of characters in the significant information section of a block is
× odd.
Also check the state (cable wiring‚ noise measures‚ etc.) of the connected
equipment.
- The control method using the DC codes‚ etc.‚ for the input/output operation is
incorrect.
×
Check the settings of the input/output unit parameters‚ and the settings on the input/
output unit side‚ and reset if necessary.
- Deletion of a machining program was attempted during operation.
- Search was attempted during operation.
×
- Change of data such as parameters was attempted during operation.
- Start of graphic check was attempted during operation.
× - There was an illegal code on the paper tape.
- Data input/output or comparison was attempted when the built-in PLC was not
stopped.
× (Measures)
- Stop the built-in PLC.
(Set the right rotary switch 2 of CNC CPU module to "1".)
- When inputting the tool offset data onto tape‚ an offset type exceeding the
× specifications range was designated‚ and that block could not be input. If the input
key is pressed again in the input screen‚ the input will continue from the next block.
- The designated character string was not found from the block displayed on the
Δ screen to the end of the program when searching with data search in the edit screen.
Press the input key again‚ and the search will start at the head of the program.
× - An inconsistency was found in the paper tape and memory data during comparison.
Details