Mitsubishi Electric 800 Series Instruction Manual page 300

Setting Signal
name
Positive Negative
logic logic
45 145 RUN3
46 146 Y46
47 147 PID
48 148 Y48
49 149 Y49
50 150 Y50
51 151 Y51
52 152 Y52
53 153 Y53
54 154 Y54
57 157 IPM
64 164 Y64
65 165 Y65
66 166 ALM3
67 167 Y67
68 168 EV
70 170 SLEEP PID output interruption
71 171 RO1
72 172 RO2
73 173 RO3
74 174 RO4
75 175 RIO1
76 176 RIO2
77 177 RIO3
78 178 RIO4
79 179 Y79
80 180 ―
82 182 Y82
85 185 Y85
Function
Inverter running and start Output while the inverter is running and the start
command is ON command is ON.
During deceleration at Output after the power-failure deceleration
occurrence of power failure function operates. (Retained until canceled.)
During PID control activated Output during PID control.
PID deviation limit Output when the absolute deviation value
exceeds the limit value.
During pre-charge operation Output during pre-charge operation.
During second pre-charge
operation
Pre-charge time over Output when the pre-charge operation reaches
the time limit set in Pr.764 or Pr.769.
Second pre-charge time
over
Pre-charge level over Output when the measured value before
reaching the ending time during pre-charge
Second pre-charge level
operation is higher than the detection level set in
over
Pr.763 or Pr.768.
During PM motor control Output while the control method is PM motor
control.
During retry Output during retry processing.
Output during emergency drive operation.
Emergency drive in
*2
operation
Fault output during Output when a fault occurs during emergency
drive operation.
*2
emergency drive
*3 Output when the power failure time
Power failure
deceleration-to-stop function is activated during
output shutoff due to power failure or
undervoltage.
24 V external power supply Output while operating with a 24 V power supply
operation input from an external source.
Output during PID output suspension function
operation.
Commercial power supply Output depending on the motor drive conditions
side motor 1 connection when the multi-pump function is used.
RO1
Commercial power supply
side motor 2 connection
RO2
Commercial power supply
side motor 3 connection
RO3
Commercial power supply
side motor 4 connection
RO4
Inverter side motor 1
connection RIO1
Inverter side motor 2
connection RIO2
Inverter side motor 3
connection RIO3
Inverter side motor 4
connection RIO4
Pulse train output of output Output in pulses every time the accumulated
power output power of the inverter reaches the Pr.799
setting.
― For manufacturer setting. Do not set.
BACnet binary output Enables output from the Binary Output object for
BACnet communication.
Output when there is a power failure or
*2
DC current feeding
undervoltage for the AC current.
Operation
―
Pr.261 to Pr.266
Pr.127 to Pr.134,
Pr.575 to Pr.577
Pr.127 to Pr.134,
Pr.553, Pr.554
Pr.127 to Pr.134,
Pr.241, Pr.553,
Pr.554, Pr.575 to
Pr.577, Pr.753 to
Pr.769, C42 to
C45
Pr.71, Pr.80,
Pr.998
Pr.65 to Pr.69
Pr.514, Pr.515,
Pr.523, Pr.524,
Pr.1013
Pr.261 to Pr.266
―
Pr.127 to Pr.134,
Pr.575 to Pr.577
Pr.575 to Pr.591
Pr.799
―
Pr.549
Pr.30
5.8 (M) Monitor display and monitor output signal
Related Refer
parameter to
3
page
303
4
458
396
5
396
424
5
5
6
151
242
245 7
8
458
9
63
396
10
429
315
―
516
553
299
5. PARAMETERS