Mitsubishi Electric 800 Series Instruction Manual page 140

Pr. Pr.
group
C223 461 Second motor constant (L2) / q-axis
inductance (Lq)
C224 462 Second motor constant (X)
C225 455 Second motor excitation current
C226 860 Second motor torque current/Rated
PM motor current
C230 738 Second motor induced voltage
constant (phi f)
C231 739 Second motor Ld decay ratio
C232 740 Second motor Lq decay ratio
C233 746 Second motor protection current
level
C235 1413 Second motor induced voltage
constant (phi f) exponent
C282 741 Second starting resistance tuning
compensation
C285 742 Second motor magnetic pole
detection pulse width
 A: Application parameters
Parameters to set a specific application.
Pr. Pr.
group
A000 135 Electronic bypass sequence
selection
A001 136 MC switchover interlock time
A002 137 Start waiting time
A003 138 Bypass selection at a fault
A004 139 Automatic switchover frequency
from inverter to bypass operation
A005 159 Automatic switchover frequency
range from bypass to inverter
operation
A006 248 Self power management selection
A007 254 Main circuit power OFF waiting
time
A170 1410 Starting times lower 4 digits
A171 1411 Starting times upper 4 digits
A300 592 Traverse function selection
A301 593 Maximum amplitude amount
A302 594 Amplitude compensation amount
during deceleration
A303 595 Amplitude compensation amount
during acceleration
A304 596 Amplitude acceleration time
A305 597 Amplitude deceleration time
A400 578 Auxiliary motor operation selection
A401 579 Motor connection function
selection
A402 580 MC switchcover interlock time
(multi-pump)
A403 581 Start waiting time (multi-pump)
A404 582 Auxiliary motor connection-time
deceleration time
A405 583 Auxiliary motor disconnection-time
acceleration time
A406 584 Auxiliary motor 1 starting
frequency
A407 585 Auxiliary motor 2 starting
frequency
Name Refer
to
page
353,
363
353
353
353,
363
363
363
363
363
363
363
363
Name Refer
to
page
376
376
376
376
376
376
385
385
388
388
389
389
389
389
389
389
429
429
429
429
429
429
429
429
Pr. Pr.
group
A408 586 Auxiliary motor 3 starting
frequency
A409 587 Auxiliary motor 1 stopping
frequency
A410 588 Auxiliary motor 2 stopping
frequency
A411 589 Auxiliary motor 3 stopping
frequency
A412 590 Auxiliary motor start detection time
A413 591 Auxiliary motor stop detection time
A414 1376 Auxiliary motor stopping level
A420 1469 Number of cleaning times monitor
A421 1470 Number of cleaning times setting
A422 1471 Cleaning trigger selection
A423 1472 Cleaning reverse rotation
frequency
A424 1473 Cleaning reverse rotation operation
time
A425 1474 Cleaning forward rotation
frequency
A426 1475 Cleaning forward rotation
operation time
A427 1476 Cleaning stop time
A428 1477 Cleaning acceleration time
A429 1478 Cleaning deceleration time
A430 1479 Cleaning time trigger
A440 1361 Detection time for PID output hold
A441 1362 PID output hold range
A442 1370 Detection time for PID limiting
operation
A443 1371 PID upper/lower limit pre-warning
level range
A444 1372 PID measured value control set
point change amount
A445 1373 PID measured value control set
point change rate
A446 1369 Check valve closing completion
frequency
A447 1363 PID priming time
A448 1364 Stirring time during sleep
A449 1365 Stirring interval time
A450 1374 Auxiliary pressure pump operation
starting level
A451 1375 Auxiliary pressure pump operation
stopping level
A452 1377 PID input pressure selection
A453 1378 PID input pressure warning level
A454 1379 PID input pressure fault level
A455 1380 PID input pressure warning set
point change amount
A456 1381 PID input pressure fault operation
selection
A457 1346 PID lower limit operation detection
time
A600 759 PID unit selection
A601 131 PID upper limit
A602 132 PID lower limit
A603 553 PID deviation limit
A604 554 PID signal operation selection
Name Refer
to
page
429
429
429
429
429
429
429
391
391
391
391
391
391
391
391
391
391
391
440
440
396,
429,
440
440
440
440
440
440
440
440
440
440
440
440
440
440
440
396,
440
421
396
396
396
396
139
5. PARAMETERS
5.1 Parameter List
3
4
5
5
5
6
7
8
9
10