Summary of Contents for Cisco Catalyst 4500 Series
Page 1
Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide Release IOS XE 3.9.xE and IOS 15.2(5)Ex Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
Page 2
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this www.cisco.com/go/trademarks...
Page 7
(netflow-lite monitor submode) F Commands flowcontrol H Commands hardware statistics hw-module beacon hw-module module start hw-module module stop hw-module port-group hw-module power hw-module system max-port-num-mode 1/2 Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
Page 8
Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex viii...
Page 9
L Commands l2protocol-tunnel Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
Page 10
(remotely-defined trigger) macro auto execute (user-defined function) macro auto global processing macro auto mac-address-group macro auto monitor macro auto processing macro auto sticky macro global apply cisco-global Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
Page 11
O Commands options timeout (netflow-lite exporter submode) P Commands packet-offset (netflow-lite sampler submode) packet-rate (netflow-lite sampler submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
3 show dot1x show environment show errdisable detect show errdisable recovery show etherchannel show flowcontrol show hw-module port-group show hw-module system max-port-num-mode Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
Page 16
Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
Page 17
Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex xvii...
Page 18
(virtual switch) show system mtu show tech-support show udld show vlan show vlan access-map show vlan counters Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex xviii...
Page 19
(interface configuration mode) udld reset unidirectional username V Commands verify vlan (VLAN Database mode) vlan access-map vlan configuration vlan database vlan dot1q tag native vlan filter vlan group Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.0E and IOS 15.2(5)Ex...
Page 21
Catalyst 4500 series switches. Cisco IOS Software Documentation In addition to the information provided in this publication, you might need to refer to the Cisco IOS documentation set. The Cisco IOS software documentation is divided into nine modules and two master indexes.
{ x | x | x } A choice of keywords (represented by x) appears in braces separated by vertical bars. You must select one. Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex xxii...
Page 24
This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex xxiv...
Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
Page 26
Obtaining Documentation and Submitting a Service Request Catalyst 4500 Series Switch Cisco IOS Command Reference—Cisco IOS XE 3.9.xE and IOS 15.2(5)Ex xxvi...
• • Saving Configuration Changes, page 1-11 For an overview of the Catalyst 4500 series switch Cisco IOS configuration, refer to the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide. Getting Help To display a list of commands that you can use within a command mode, enter a question mark (?) at the system prompt.
To display keywords for a command, enter a question mark (?) at the command prompt or after entering part of a command followed by a space. The Catalyst 4500 series switch software displays a list of available keywords along with a brief description of the keywords. For example, if you are in global configuration mode and want to see all the keywords for the arap command, you enter arap ?.
In this example, you must enter the group keyword. Because a is not displayed, it <cr> indicates that you must enter more information to complete the command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 30
Return to complete the command. In this example, press Return to Switch(config-if)# channel-group 1 mode auto Switch(config-if)# complete the command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
ROM-monitor mode is a separate mode used when the Catalyst 4500 series switch cannot boot properly. If your Catalyst 4500 series switch or access server does not find a valid system image when it is booting, or if its configuration file is corrupted at startup, the system might enter ROM-monitor mode.
Regular expressions are case sensitive and allow for complex matching requirements. Examples of simple regular expressions are Serial, misses, and 138. Examples of complex regular expressions are 00210..., ( is ), and [Oo]utput. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
To enter these special characters as single-character patterns, remove the special meaning by preceding each character with a backslash (\). These examples are single-character patterns matching a dollar sign, an underscore, and a plus sign, respectively. \$ \_ \+ Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 34
You can remove the special meaning of the period character by putting a backslash in front of it. In the following expression: only the string a. matches this regular expression. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 35
Concatenated constructs are matched beginning at the left side of the construct. Thus, the regular expression matches A9b3, but not 9Ab3 because the letters are specified before the numbers. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 36
21300 and 13000 do not. Using the underscore character, you can replace long regular expression lists, such as the following: ^1300$ ^1300(space) (space)1300 {1300, ,1300, {1300} ,1300, (1300 with _1300_ Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 1-10...
Do not use these commands unless your technical support representative asks you to do so. The show platform commands are not described in this document. Note Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 1-11...
Page 38
Chapter 1 Command-Line Interface show platform Commands Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 1-12...
Page 39
Cisco IOS Commands for the Catalyst 4500 Series Switches This chapter contains an alphabetical listing of Cisco IOS commands for the Catalyst 4500 series switches. For information about Cisco IOS commands that are not included in this publication, refer to Cisco IOS Release 12.2 configuration guides and command references at this URL:...
#macro keywords $VLAN $MAX swichport Switch(config)# int gi1/1 Switch(config-if)# macro apply test ? WORD Keyword to replace with a value e.g $VLAN, $MAX << It is shown as help <cr> Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex OL-30934-01...
Page 41
Enables the Cisco-recommended features and settings that are suitable for connecting a switch port to another switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 42
The RADIUS authentication server must be properly configured to accept and log update or watchdog Note packets from the AAA client. Related Commands Command Description aaa accounting system default Receives the session termination messages after the switch start-stop group radius reboots. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex OL-30934-01...
Page 43
The RADIUS authentication server must be properly configured to accept and log update or watchdog Note packets from the AAA client. Related Commands Command Description aaa accounting dot1x default Enables accounting for 802.1X authentication sessions. start-stop group radius Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 44
The following example shows how to make the PACL mode on the switch take effect: (config-if)# access-group mode prefer port The following example shows how to merge applicable ACL features: (config-if)# access-group mode merge Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex OL-30934-01...
Page 45
Displays the ACL configuration on a Layer 2 interface. interface show ip interface (refer to Displays the IP interface configuration. Cisco IOS documentation) show mac access-group Displays the ACL configuration on a Layer 2 interface. interface Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 46
The following example shows how to configure the switch to capture control packets globally across all VLANs (using a static ACL): Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# access-list hardware capture mode global Switch(config)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex OL-30934-01...
Page 47
The following example shows another way to configure the switch to capture control packets globally across all VLANs: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# no access-list hardware capture mode vlan Switch(config)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 49
0 / 4096 ( 512 ( Output Qos(PortAndVlan) 0 / 4096 ( 512 ( Output Qos(PortOrVlan) 0 / 4096 ( 512 ( L4Ops: used 2 out of 64 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-11...
Page 50
The following example shows how to enable the MAC notification trap when a MAC address is added to a port: Switch# configure terminal Switch(config)# access-list hardware region feature input balance 75 Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-12 OL-30934-01...
Page 51
VLAN access-map sequence. show vlan access-map Displays the contents of a VLAN access map. vlan access-map Enters VLAN access-map command mode to create a VLAN access map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-13...
Page 52
Subscribes this destination profile to the Configuration alert group. subscribe-to-alert-group diagnostic Subscribes this destination profile to the Diagnostic alert group. subscribe-to-alert-group environment Subscribes this destination profile to the Environment alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-14 OL-30934-01...
Page 53
Cisco IOS Commands for the Catalyst 4500 Series Switches active Command Description subscribe-to-alert-group inventory Subscribes this destination profile to the Inventory alert group. subscribe-to-alert-group syslog Subscribes this destination profile to the Syslog alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-15...
Page 54
Switch# ancp client port identifier NArmstrong vlan 10 interface FastEthernet 7/3 Related Commands Command Description ancp mode client Sets the router to become an ANCP client. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-16 OL-30934-01...
Page 55
Switch# ancp client server 10.1.2.31 interface FastEthernet 2/1 Related Commands Command Description ancp mode client Sets the router to become an ANCP client. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-17...
Page 56
The following example shows how to set the router to become an ANCP client: Switch# ancp mode client Related Commands Command Description ancp client server Displays multicast streams activated by ANCP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-18 OL-30934-01...
Page 57
Leaves the proposed new VLAN database but remains in VLAN configuration mode and resets the proposed new database to be identical to the VLAN database currently implemented. show vlan Displays VLAN information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-19...
Page 58
Command Description shutdown vlan (refer to Cisco Shuts down VLAN switching. IOS documentation) vtp (global configuration Modifies the name of a VTP configuration storage file. mode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-20 OL-30934-01...
Page 59
DAI is enabled and to define an ARP access list and applies it to a VLAN. permit Permits an ARP packet based on matches against the DHCP bindings. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-21...
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines This command applies only to the Access Gateway Module on Catalyst 4500 series switches. The valid values for mod depend on the chassis that are used. For example, if you have a Catalyst 4506 chassis, valid values for the module are from 2 to 6.
Page 61
Bidirectional state—When you configure a port as bidirectional with the dot1x control-direction • interface configuration command, the port is access-controlled in both directions. In this state, the switch port sends only EAPOL. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-23...
Page 62
The following example shows how to return to the default settings: Switch(config-if)# no authentication control-direction Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-24 OL-30934-01...
Page 63
The following example shows how to set the recovery delay period that the switch waits to reinitialize a critical port when an unavailable RADIUS server becomes available: Switch(config)# authentication critical recovery delay 1500 Switch(config)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-25...
Page 64
The current authentication method is retried indefinitely (and fails each time) until the AAA server • becomes reachable. Command Modes Interface configuration mode Command History Release Modification 12.2(50)SG This command was introduced. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-26 OL-30934-01...
Page 65
The following example shows how to specify the conditions when a client doesn't support 802.1X to authorize the port for authentication events: Switch(config-if)# authentication event authentication event no-response action authorize vlan 10 Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-27...
Page 66
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches authentication event Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-28 OL-30934-01...
Page 67
Switch(config-if)# authentication fallback fallbacktest1 Switch(config-if)# The following example shows how to disable WebAuth fallback: Switch(config-if)# no authentication fallback fallbacktest1 Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-29...
Page 68
MAC/IP only and will not affect the other on the same port. The clients can be authenticated using different methods (such as 802.1X for PC, MAB for IP phone, or vice versa). No restriction exists on the authentication order. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-30 OL-30934-01...
Page 69
The following example shows how to define the classification of a session that are used to apply the access-policies using the host-mode configuration: Switch(config-if)# authentication host-mode single-host Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-31...
Page 70
The following example shows how to enable open access to a port: Switch(config-if)# no authentication open Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-32 OL-30934-01...
Page 71
For authentication fails, failover to the next authentication method occurs (subject to the configuration of authentication event handling). You can verify your settings with the show authentication privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-33...
Page 72
The following example shows how to specify the order in which authentication methods should be attempted for a client on an interface: Switch(config-if)# authentication order mab dot1x webauth Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-34 OL-30934-01...
Page 73
The following example shows how to disable reauthentication for this port: Switch(config-if)# no authentication reauthentication Switch(config-if)# Related Commands Command Description authentication timer Configures the authentication timer. show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-35...
Page 74
EtherChannel, an error message appears, and 802.1X is not enabled. If you enable 802.1X on a not-yet active port of an EtherChannel, the port does not join the EtherChannel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-36...
Page 75
The following example shows that the authentication status of the client PC will be determined by the authentication process: Switch(config-if)# authentication port-control auto Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-37...
Page 76
You can verify your settings with the show authentication privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-38 OL-30934-01...
Page 77
Related Commands Command Description authentication order Specifies the order in which authentication methods should be attempted for a client on an interface. show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-39...
Page 78
Cisco IOS Release 12.2(50)SG and later releases: [no] dot1x timeout {reauth-period seconds | quiet-period seconds | tx-period seconds | supp-timeout seconds | server-timeout seconds} Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-40 OL-30934-01...
Page 79
(AAA) server as Session-Timeout (RADIUS Attribute 27): Switch(config-if)# authentication timer reauthenticate server Switch(config-if)# Related Commands Command Description show authentication Displays Authentication Manager information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-41...
Page 80
%AUTHMGR-5-SECURITY_VIOLATION: Security violation on the interface <interface name>, new MAC address <mac-address> is seen. %PM-4-ERR_DISABLE: security-violation error detected on <interface name>, putting <interface name> in err-disable state Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-42 OL-30934-01...
Page 81
Adds an authentication method to the port-priority list. priority authentication timer Configures the timeout and reauthentication parameters for an 802.1x-enabled port. show authentication Displays information about authentication manager events on the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-43...
Page 82
465 permit tcp any any eq 143 permit tcp any any eq 993 permit tcp any any eq pop3 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-44 OL-30934-01...
Page 83
AutoQos-4.0-VoIP-Data-Cos and AutoQos-4.0-VoIP-Signal-Cos are needed to handle instances when you connect an IP phone to an interface and call the auto qos voip cisco-phone command on that interface. In this situation, the input service policy on the interface must match VoIP and signaling packets solely on their CoS markings.
Page 84
10 class AutoQos-4.0-Multimedia-Stream-Queue bandwidth remaining percent 10 class AutoQos-4.0-Trans-Data-Queue bandwidth remaining percent 10 class AutoQos-4.0-Bulk-Data-Queue bandwidth remaining percent 4 class class-default bandwidth remaining percent 25 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-46 OL-30934-01...
Page 85
Generate QoS configurations for trusted interfaces. auto qos voip cisco-softphone Generate QoS configuration for interfaces connected to PCs running the Cisco IP SoftPhone application and marks police traffic coming from such interfaces. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-47...
Page 86
AutoQos-4.0-ACL-Signaling permit tcp any any range 2000 2002 permit tcp any any range 5060 5061 permit udp any any range 5060 5061 ip access-list extended AutoQos-4.0-ACL-Transactional-Data Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-48 OL-30934-01...
Page 87
AutoQos-4.0-VoIP-Data-Cos and AutoQos-4.0-VoIP-Signal-Cos are needed to handle the case in which a user connects an IP phone to an interface and calls the auto qos voip cisco-phone command on that interface. In this situation, the input service policy on the interface must match VoIP and signaling packets solely on their CoS markings because switching ASICs on Cisco IP phones are limited to only remarking the CoS bits of VoIP and signaling traffic.
Page 88
AutoQos-4.0-Multimedia-Stream-Queue match qos-group 26 class-map match-all AutoQos-4.0-Trans-Data-Queue match qos-group 18 class-map match-all AutoQos-4.0-Bulk-Data-Queue match qos-group 10 class-map match-any AutoQos-4.0-Scavenger-Queue match qos-group 8 match dscp cs1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-50 OL-30934-01...
Page 89
Generates a QoS configuration for an untrusted interface. auto qos srnd4 Generates QoS configurations based on solution reference network design 4.0. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-51...
Page 90
AutoQos-4.0-Input-Policy, it makes sense to include that policy in the same template that defines the application classes used by the previous three commands. class-map match-any AutoQos-4.0-VoIP match dscp ef Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-52 OL-30934-01...
Page 91
AutoQos-4.0-Scavenger match dscp cs1 The AutoQos-4.0-Signaling and AutoQos-4.0-VoIP classes must match on CoS to handle the situation when an IP phone is connected to an interface. (Cisco IP phones are only capable of re-marking CoS bits, not DSCP.) policy-map AutoQos-4.0-Input-Policy class AutoQos-4.0-VoIP...
Page 92
Switch(config-if)# no service-policy input AutoQos-VoIP-Input-Cos-Policy no service-policy output AutoQos-VoIP-Output-Policy service-policy input AutoQos-4.0-Input-Policy service-policy output AutoQos-4.0-Output-Policy If Layer 3 interface: Switch(config-if)# no service-policy input AutoQos-VoIP-Input-Dscp-Policy no service-policy output AutoQos-VoIP-Output-Policy Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-54 OL-30934-01...
Page 93
Generate QoS configurations for trusted interfaces. auto qos voip cisco-softphone Generate QoS configuration for interfaces connected to PCs running the Cisco IP SoftPhone application and marks police traffic coming from such interfaces. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-55...
Page 94
AutoQos-4.0-VoIP match dscp ef match cos 5 class-map match-all AutoQos-4.0-Broadcast-Vid match dscp cs5 class-map match-all AutoQos-4.0-Realtime-Interact match dscp cs4 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-56 OL-30934-01...
Page 95
The AutoQos-4.0-Signaling and AutoQos-4.0-VoIP classes must also match on CoS to handle the case when an IP phone is connected to an interface. (Cisco IP phones are only capable of remarking CoS bits, not DSCP.) policy-map AutoQos-4.0-Input-Policy class AutoQos-4.0-VoIP...
Page 96
The following example shows how to police traffic from an untrusted interface gigabitethernet1/1: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# auto qos trust Switch(config-if)# do sh running interface interface-id interface FastEthernet2/1 auto qos trust service-policy input AutoQos-4.0-Input-Policy service-policy output AutoQos-4.0-Output-Policy Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-58 OL-30934-01...
Page 97
Generates a QoS configuration for an untrusted interface. auto qos srnd4 Generates QoS configurations based on solution reference network design 4.0. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-59...
Page 98
This command was introduced on the Catalyst 4500 series switch. 15.1(1)SG IOS-XE 3.3.0 Usage Guidelines The auto qos video command trusts an interface only if Cisco TelePresence is detected. Else, the port is untrusted. Global Level Commands Generated When auto-Qos srnd4 commands are applied to an interface, they generate one or more of the following templates at the global configuration level.
Page 99
AutoQos-4.0-Scavenger match dscp cs1 The AutoQos-4.0-Signaling and AutoQos-4.0-VoIP classes must also match on CoS to the case where an IP phone is connected to an interface. (Cisco IP phones are only capable of remarking CoS bits, not DSCP.) policy-map AutoQos-4.0-Input-Policy class AutoQos-4.0-VoIP...
Page 100
For Fa/Gig Ports: Switch(config-if)# service-policy input AutoQos-4.0-Input-Policy service-policy output AutoQos-4.0-Output-Policy Examples The following example shows how to generate a QoS configuration on the cisco-telepresence interface gigabitethernet1/1: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# auto qos video cts Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 101
AutoQos-4.0-Input-Policy service-policy output AutoQos-4.0-Output-Policy The following example shows how to generate QoS configuration for the cisco-camera interface gigabitethernet1/1: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# auto qos video ip-camera Switch(config-if)# do sh running interface interface-id...
CoS label that is received in the packet because some older phones do not mark DSCP. When a Cisco IP phone is absent, the ingress classification is set to not trust the CoS label in the packet.
Page 103
Switch(config-if)# auto qos voip trust The following example shows how to enable auto-QoS and to trust the CoS labels that are received in incoming packets when the device connected to Fast Ethernet interface 2/1 is detected as a Cisco IP phone:...
Page 104
Displays the automatic quality of service (auto-QoS) configuration that is applied. show qos Displays QoS information. show qos interface Displays queueing information. show qos maps Displays QoS map information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-66 OL-30934-01...
The global template is defined by A, B, and C. A. Template for ACLs and application classes used by the auto qos voip cisco-softphone command ip access-list extended AutoQos-4.0-ACL-Multimedia-Conf permit udp any any range 16384 32767 ip access-list extended AutoQos-4.0-ACL-Signaling...
AutoQos-4.0-VoIP-Data-Cos and AutoQos-4.0-VoIP-Signal-Cos handles those instances when a user connects an IP phone to an interface and enters the auto qos voip cisco-phone command on that interface. In this situation, the input service policy on the interface must match VoIP and signaling packets based solely on their CoS markings because switching ASICs on Cisco IP Phones are limited to only remarking the CoS bits of VoIP and signaling traffic.
Page 107
C. Template for egress queue classes and the srnd4 output policy that uses the egress classes to allocate eight queues. This template is required by all srnd4 commands: class-map match-all AutoQos-4.0-Priority-Queue match qos-group 32 class-map match-all AutoQos-4.0-Control-Mgmt-Queue match qos-group 16 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-69...
Page 108
PC that is running the Cisco IP SoftPhone application: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# auto qos voip cisco-softphone Switch(config-if)# do sh running interface gigabitethernet1/1 interface gigabitethernet1/1 auto qos voip cisco-phone qos trust device cisco-phone Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-70 OL-30934-01...
Page 109
Cisco IP SoftPhone application and marks police traffic coming from such interfaces. auto qos classify Generate a QoS configuration for an untrusted interface. auto qos classify police Police traffic form an untrusted interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-71...
Page 110
Examples The following example shows how to enable auto security globally: Switch(config)# auto security Switch# show running-config | i security auto security Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-72 OL-30934-01...
Page 111
3.6.0E This command was introduced on the Catalyst 4500 series switch. Usage Guidelines This command is supported on Catalyst 3750X, Catalyst 2960S, and the Catalyst 4500 series starting with Cisco IOS Release 15.2(2)E. Examples The following example shows how to enable auto security on a host-facing port: Switch# conf t Enter configuration commands, one per line.
Page 112
Redundancy main-cpu mode Command History Release Modification 12.1(12c)EW This command was introduced on the Catalyst 4500 series switch (Catalyst 4507R only). Usage Guidelines If you enter the no auto-sync standard command, no automatic synchronizations occur. Examples The following example shows how (from the default configuration) to enable automatic synchronization...
Page 113
The following example shows how to configure a monitor on a port interface Gigabit 1/3: Switch# config terminal Switch(config)# int GigabitEthernet1/3 Switch(config-if)# netflow-lite monitor 1 Switch(config-netflow-lite-monitor)# sampler sampler1 Switch(config-netflow-lite-monitor)# exporter exporter1 Switch(config-netflow-lite-monitor)# average-packet-size 128 Switch(config-netflow-lite-monitor)# exit Switch(config-if)# exit Switch(config)# exit Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-75...
Page 114
Command Description sampler (netflow-lite monitor Activates sampling on an interface in netflow-lite monitor submode) submode. exporter (netflow-lite monitor Assigns an exporter in netflow-lite monitor submode. submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-76 OL-30934-01...
Page 115
Command History Release Modification 12.2(40)SG This command was introduced on the Catalyst 4500 series switch using a Supervisor Engine 6E. Usage Guidelines Use the bandwidth command only in a policy map attached to a physical port. The bandwidth command specifies the minimum bandwidth for traffic in that class when there is traffic congestion in the switch.
Page 116
Switch(config-pmap-c)# exit Switch(config-pmap)# end Switch(config)# interface gigabitethernet1/1 Switch(config-if)# service-policy output policy1 Switch(config-if)# end You can verify your settings by entering the show policy-map privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-78 OL-30934-01...
Page 117
(class-based queueing) Enables traffic shaping a class of traffic in a policy map attached to a physical port. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-79...
Page 118
Examples The following configuration is auto-generated when this command is run on your device: Device(config-fabric-auto-domain)#border 198.51.100.4 ipv4 use-petr 198.51.100.4 priority 10 weight 10 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-80 OL-30934-01...
Page 119
Device(config)# ipv6 dhcp pool pool1 Device(config-dhcpv6)# capwap-ac address 2001:DB8::1 Device(config-dhcpv6)# end Related CommandsT Command Description ipv6 dhcp pool Configures a DHCPv6 server configuration information pool and enters DHCPv6 pool configuration mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-81...
Page 120
(target-profile) with • the same configuration settings as the existing profile (source-profile). customer-id name—Provides customer identification for Cisco AutoNotify. You can enter up to 256 • alphanumeric characters. If you include spaces, you must enclose your entry in quotes (“ ”).
Page 121
You can enter up to 128 alphanumeric characters in e-mail address format with no spaces. • site-id alphanumeric—Specifies the site identification for Cisco AutoNotify. You can enter up to 256 alphanumeric characters. If you include spaces, you must enclose your entry in quotes (“ ”).
Page 122
(refer to Cisco Enables an alert group. IOS documentation) profile (refer to Cisco IOS Enters call-home profile configuration mode. documentation) show call-home Displays call home configuration information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-84 OL-30934-01...
Page 123
Cisco TAC and the user can receive the reply from the Smart Call Home service. Based on the keyword specifying the type of report requested, the following information is returned in response to the request: config-sanity—Information on best practices as related to the current running configuration.
Page 124
Sends a specific alert group message. service call-home (refer to Cisco Enables or disables Call Home. IOS documentation) show call-home Displays call-home configuration information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-86 OL-30934-01...
Page 125
The command output is then sent by e-mail to the specified e-mail address. If no e-mail address is specified, the command output is sent to the Cisco TAC at attach@cisco.com. The e-mail is sent in long text format with the service number, if specified, in the subject line.
Page 126
Switch# call-home send alert-group diagnostic module 3 profile Ciscotac1 The following example shows how to send the inventory call-home message: Switch# call-home send alert-group inventory Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-88 OL-30934-01...
Page 127
Sends a call-home test message that you define. service call-home (refer to Cisco Enables or disables Call Home. IOS documentation) show call-home Displays call-home configuration information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-89...
Page 128
Sends a specific alert group message. alert-group service call-home (refer to Enables or disables Call Home. Cisco IOS documentation) show call-home Displays call-home configuration information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-90 OL-30934-01...
Page 129
You do not have to disable the IP address that is assigned to a physical interface that is part of a channel group, but we recommend that you do so. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-91...
Page 130
Related Commands Command Description interface port-channel Accesses or creates a port-channel interface. show interfaces port-channel Displays the information about the Fast EtherChannel. (refer to Cisco IOS documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-92 OL-30934-01...
Page 131
For a complete list of guidelines, refer to the “Configuring EtherChannel” section of the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide. Examples The following example shows how to select LACP to manage channeling on the interface: Switch(config-if)# channel-protocol lacp Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-93...
Page 132
Cisco IOS Commands for the Catalyst 4500 Series Switches channel-protocol Related Commands Command Description channel-group Assigns and configures an EtherChannel interface to an EtherChannel group. show etherchannel Displays EtherChannel information for a channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-94 OL-30934-01...
Page 133
Related Commands Command Description dot1x credentials (global Configures a profile on a supplicant switch. configuration) show cisp Displays CISP information for a specified interface. Refer to IOS documentation. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-95...
Page 134
For more information, see the police command. For more information about the two-rate policer, see the police (two rates) and the police (percent) command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-96 OL-30934-01...
Page 135
Switch(config-pmap-c)# police 1000000 20000 exceed-action policed-dscp-transmit Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface fastethernet1/0/4 Switch(config-if)# service-policy input policy1 Switch# You can verify your settings by entering the show policy-map privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-97...
Page 136
Displays information about the policy map. trust Defines a trust state for traffic classified through the class policy-map configuration command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-98 OL-30934-01...
Page 137
Exits from QoS class-map configuration mode. • match Configures classification criteria. For more information, see the match (class-map • configuration) command. no Removes a match statement from a class map. • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-99...
Page 138
Creates a policy map that can be attached to multiple ports to specify a service policy and to enter policy-map configuration mode. show class-map Displays class map information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-100 OL-30934-01...
The following example shows how to clear the counters on a specific interface: Switch# clear counters vlan 200 Clear "show interface" counters on this interface [confirm]y Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-101...
Page 140
Cisco IOS Commands for the Catalyst 4500 Series Switches clear counters Related Commands Command Description show interface counters (refer Displays interface counter information. to Cisco IOS documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-102 OL-30934-01...
Switch# clear errdisable interface ethernet2 vlan 10-15 Switch# Related Commands Command Description errdisable detect cause Enables error-disabled detection for a specific cause or all causes. errdisable recovery Configures the recovery mechanism variables. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-103...
Page 142
Displays error-disabled detection status. show errdisable recovery Display error-disabled recovery timer information. show interfaces status Displays interface status of a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-104 OL-30934-01...
Page 143
The following example shows how to clear the password from slot 5 on a line module: Switch# clear hw-module slot 5 password Switch# Related Commands Command Description hw-module power Turns the power off on a slot or line module. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-105...
The following example shows how to clear the hardware logic from a Gigabit Ethernet IEEE 802.3z interface: Switch# clear interface gigabitethernet 1/1 Switch# Related Commands Command Description show interfaces status Displays the interface status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-106 OL-30934-01...
The following example shows how to clear the hardware logic from a specific VLAN: Switch# clear interface vlan 5 Switch# Related Commands Command Description show interfaces status Displays the interface status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-107...
Page 146
This command was introduced on the Catalyst 4500 series switch. Examples The following example shows how to clear the statistical information for an access list: Switch# clear ip access-template 201 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-108 OL-30934-01...
Defines an ARP access list or adds clauses at the end of a predefined list. show ip arp inspection log Displays the status of the log buffer. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-109...
Clears the status of the log buffer. show ip arp inspection log Displays the status of the log buffer. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-110 OL-30934-01...
Switch# clear ip dhcp snooping binding interface gigabitEthernet 1/1 Switch# The following example shows how to clear all the DHCP snoop binding entries on VLAN 40: Switch# clear ip dhcp snooping binding vlan 40 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-111...
Page 150
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-112 OL-30934-01...
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-113...
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-114 OL-30934-01...
To delete all the entries from the IGMP cache, enter the clear ip igmp group command with no arguments. Examples The following example shows how to clear the entries for a specific group from the IGMP cache: Switch# clear ip igmp group 224.0.255.1 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-115...
Page 154
Internet Group Management Protocol (IGMP), use the show ip igmp groups command in EXEC mode. show ip igmp interface Displays the information about the IGMP-interface status and configuration. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-116 OL-30934-01...
The following example shows how to clear all the active MFIB routes and global counters: Switch# clear ip mfib counters Switch# Related Commands Command Description show ip mfib Displays all active Multicast Forwarding Information Base (MFIB) routes. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-118 OL-30934-01...
Related Commands Command Description ip mfib fastdrop Enables MFIB fast drop. show ip mfib fastdrop Displays all currently active fast-drop entries and shows whether fast drop is enabled. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-119...
Page 158
Description ip wccp Enables support of the specified WCCP service for participation in a service group. show ip wccp Displays global statistics related to the WCCP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-120 OL-30934-01...
The following example shows how to clear the statistics for a specific group: Switch# clear lacp 1 counters Switch# Related Commands Command Description show lacp Displays LACP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-121...
Page 160
The following example shows how to clear all the dynamic Layer 2 entries for a specific interface (gi1/1): Switch# clear mac-address-table dynamic interface gi1/1 Switch# The following example shows how to clear the MAC address notification counters: Switch# clear mac-address-table notification Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-122 OL-30934-01...
Page 161
Enters the main CPU submode and manually synchronizes the configurations on two supervisor engines. show mac-address-table address Displays the information about the MAC-address table. snmp-server enable traps Enables SNMP notifications. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-123...
Page 162
Configures the aging time for entries in the Layer 2 table. main-cpu Enters the main CPU submode and manually synchronizes the configurations on two supervisor engines. show mac-address-table address Displays the information about the MAC-address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-124 OL-30934-01...
Page 163
The following examples show how to clear statistics of a packet sampler at a monitor: Switch# clear netflow-lite exporter e1 statistics Related Commands Command Description clear netflow-lite monitor Clears statistics of a packet sampler at a monitor. statistics interface Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-125...
Page 164
Switch# clear netflow-lite monitor 1 statistics int gi1/1 Switch# clear netflow-lite monitor 1 statistics vlan 10 Related Commands Command Description clear netflow-lite exporter Clear the collector statistics. statistics Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-126 OL-30934-01...
Page 165
Switch# clear nmsp statistics Switch# You can verify that information was deleted by entering the show nmsp statistics command. Related Commands Command Description show nmsp Displays the NMSP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-127...
The following example shows how to clear all the port-channel traffic filters: Switch# clear pagp counters Switch# Related Commands Command Description show pagp Displays information about the port channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-128 OL-30934-01...
Page 167
Switch# clear port-security dynamic The following example shows how to remove a dynamic secure address from the MAC address table: Switch# clear port-security dynamic address 0008.0070.0007 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-129...
Page 168
You can verify that the information was deleted by entering the show port-security command. Related Commands Command Description show port-security Displays information about the port-security setting. switchport port-security Enables port security on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-130 OL-30934-01...
Page 169
The following example shows how to clear PPPoE Intermediate Agent statistics: Switch# clear pppoe intermediate-agent statistics Related Commands Command Description show pppoe Displays PPPoE Intermediate Agent statistics (packet counters). intermediate-agent interface Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-131...
Switch# clear qos Switch# The following example shows how to clear the specific protocol aggregate QoS counters for all the interfaces: Switch# clear qos aggregate-policer Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-132 OL-30934-01...
Page 171
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches clear qos Related Commands Command Description show qos Displays QoS information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-133...
Page 172
Description dual-active detection (virtual Enables and configures dual-active detection. switch) snmp ifindex clear Configures the VSS domain number and enter the virtual switch domain configuration submode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-134 OL-30934-01...
The following example shows how to clear the software-cached counter values for a specific VLAN: Switch# clear vlan 10 counters Clear "show vlan" counters on this vlan [confirm] y Switch# Related Commands Command Description show vlan counters Displays VLAN counter information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-135...
Switch(config)# class-map telnet-class Switch(config-cmap)# match access-group 140 Switch(config-cmap)# exit Switch(config)# policy-map control-plane Switch(config-pmap)# class telnet-class Switch(config-pmap-c)# police 32000 1000 conform transmit exceed drop Switch(config-pmap-c)# exit Switch(config-pmap)# exit Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-137...
Page 176
Attaches a policy map to an interface. configuration) show policy-map Displays the configuration either of a class or of all classes for the control-plane policy map of a control plane. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-138 OL-30934-01...
Page 177
The following configuration is auto-generated when this command is run on your device: Device(config-fabric-auto-domain)# context guest id 10 ip vrf guest description Auto-provisioned vrf for context example-context (source – fabric auto) router lisp eid-table vrf guest instance-id 10 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-139...
Page 181
(netflow-lite exporter submode) options timeout (netflow-lite Specifies an options timeout for the NetFlow-lite collector. exporter submode) export-protocol (netflow-lite Specifies the export protocol for the NetFlow-lite collector. exporter submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-143...
Page 182
End with CNTL/Z. Switch(config)# interface vlan 1 Switch(config-if)# counter ipv4 Switch(config-if)# end Switch# 00:17:15: %SYS-5-CONFIG_I: Configured from console by console Switch# show run interface vlan 1 Building configuration... Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-144 OL-30934-01...
Page 183
Switch(config-if)# end Switch# 00:24:18: %SYS-5-CONFIG_I: Configured from console by console In this situation, you must release a counter from another interface so the new interface can use it. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-145...
Page 184
Creates a signaling class structure that can be referred to by its name. class Creates a class map to be used for matching packets to the class whose name you specify and to enter class-map configuration mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-146 OL-30934-01...
Page 185
(policy-map Creates a service policy that is a quality of service (QoS) policy class) within a policy map. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-147...
The following example shows how to debug the backup events: Switch# debug backup Backup events debugging is on Switch# Related Commands Command Description undebug backup (same as no Disables debugging output. debug backup) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-149...
Command Description debug interface Abbreviates the entry of the debug condition interface command. undebug condition interface Disables interface related activities. (same as no debug condition interface) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-150 OL-30934-01...
The following example shows how to limit the debugging output to group 0 in VLAN 1: Switch# debug condition standby vlan 1 0 Condition 3 set Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-151...
Page 190
Proceed with removal? [yes/no]: n % Operation aborted Switch# Related Commands Command Description undebug condition standby Disables debugging output. (same as no debug condition standby) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-152 OL-30934-01...
Removing all conditions may cause a flood of debugging messages to result, unless specific debugging flags are first removed. Proceed with removal? [yes/no]: n % Operation aborted Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-153...
Page 192
Cisco IOS Commands for the Catalyst 4500 Series Switches debug condition vlan Related Commands Command Description undebug condition vlan (same Disables debugging output. as no debug condition vlan) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-154 OL-30934-01...
Page 193
Examples The following is sample output from the debug device-sensor events command. The debug output shows how Cisco Discovery Protocol packets and TLVs are received from the device connected to the GigabitEthernet 2/1 interface: Switch# debug device-sensor events Switch# *Nov 30 23:58:45.811: DSensor: Received cdp packet from GigabitEthernet2/1:00d0.2bdf.08a5...
Page 194
Displays all debugging information abou Authentication Manager and all features. device-sensor Adds the Device Sensor protocol data to the accounting records and accounting generates additional accounting events when new sensor data is detected. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-156 OL-30934-01...
The following example shows how to enable the 802.1X debugging for all conditions: Switch# debug dot1x all Switch# Related Commands Command Description show dot1x Displays dot1x information. undebug dot1x (same as no Disables debugging output. debug dot1x) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-157...
22:46:33:FEC:pagp_switch_choose_unique:Fa2/25, port Fa2/15 in agport Po3 is incompatable Switch# The following example shows how to display the EtherChannel IDB debug messages: Switch# debug etherchnl idb Agport idb related debugging is on Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-158 OL-30934-01...
Page 197
The following example shows how to disable the debugging: Switch# no debug etherchnl Switch# Related Commands Command Description undebug etherchnl (same as no Disables debugging output. debug etherchnl) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-159...
Page 198
The no debug fabric auto level verbose command disables the display of all the messages encountered during fabric provisioning. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-160 OL-30934-01...
The following example shows how to enable the debugging of the IPC events: Switch# debug ipc events Special Events debugging is on Switch# Related Commands Command Description undebug ipc (same as no debug Disables debugging output. ipc) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-162 OL-30934-01...
The following example shows how to disable the debugging for the DHCP snooping events: Switch# no debug ip dhcp snooping event Switch# Related Commands Command Description debug ip dhcp snooping Debugs the DHCP snooping messages. packet Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-163...
The following example shows how to disable the debugging for the DHCP snooping packets: Switch# no debug ip dhcp snooping packet Switch# Related Commands Command Description debug ip dhcp snooping event Debugs the DHCP snooping events. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-164 OL-30934-01...
Enables DHCP snooping on a trusted VLAN. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-165...
The following example shows how to enable the LACP miscellaneous debugging: Switch# debug lacp Port Aggregation Protocol Miscellaneous debugging is on Switch# Related Commands Command Description undebug pagp (same as no debug pagp) Disables debugging output. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-166 OL-30934-01...
The following example shows how to debug the monitoring errors: Switch# debug monitor errors SPAN error detail debugging is on Switch# Related Commands Command Description undebug monitor (same as no debug Disables debugging output. monitor) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-167...
Page 206
The undebug nmsp command is the same as the no debug nmsp command. Related Commands Command Description show debugging Displays information about the types of debugging that are enabled. show nmsp Displays the NMSP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-168 OL-30934-01...
The following example shows how to debug NVRAM: Switch# debug nvram NVRAM behavior debugging is on Switch# Related Commands Command Description undebug nvram (same as no debug Disables debugging output. nvram) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-169...
Switch# debug platform packet protocol pagp Switch# Related Commands Command Description undebug platform packet protocol Disables debugging output. pagp (same as no debug platform packet protocol pagp) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-172 OL-30934-01...
Page 211
The following example shows how to enable all PM debugging: Switch# debug pm all Switch# Related Commands Command Description undebug pm (same as no debug pm) Disables debugging output. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-173...
Page 212
The following example shows how to enable all PM debugging: Switch# debug port-security Switch# Related Commands Command Description switchport port-security Enables port security on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-174 OL-30934-01...
Page 213
Gi3/4, vlan : 2 MAC da: aabb.cc00.0000, MAC sa: 001d.e64c.6512 The following example shows how to turn off packet debugging: Switch# debug pppoe intermediate-agent packet PPPOE IA Packet debugging is off Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-175...
Page 214
Limits the rate of the PPPoE Discovery packets arriving on an limit rate interface. pppoe intermediate-agent Sets the trust configuration of an interface. trust Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-176 OL-30934-01...
Privileged EXEC mode Command History Release Modification 12.1(12c)EW This command was introduced on the Catalyst 4500 series switch (Catalyst 4507R only). Examples The following example shows how to debug the redundancy facility timer event debugging: Switch# debug redundancy timer Redundancy timer debugging is on Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 216
This command was introduced on the Catalyst 4500 series switch. Examples The following example shows how to debug the spanning-tree PVST+: Switch# debug spanning-tree pvst+ Spanning Tree PVST+ debugging is on Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-178 OL-30934-01...
Page 217
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug spanning-tree Related Commands Command Description undebug spanning-tree (same as no Disables debugging output. debug spanning-tree) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-179...
Page 218
Switch# debug spanning-tree backbonefast detail Spanning Tree backbonefast detail debugging is on Switch# Related Commands Command Description undebug spanning-tree backbonefast Disables debugging output. (same as no debug spanning-tree backbonefast) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-180 OL-30934-01...
Page 219
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines This command is supported only on the supervisor engine and enterable only from the switch console. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-181...
Page 220
*Sep 30 08:47:33: SP: STP SW: TX: bpdu of type ieee-st size 92 on FastEthernet5/9 801 <... output truncated...> Switch# Related Commands Command Description undebug spanning-tree switch (same as Disables debugging output. no debug spanning-tree switch) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-182 OL-30934-01...
Page 221
Switch# debug spanning-tree uplinkfast exceptions Spanning Tree uplinkfast exceptions debugging is on Switch# Related Commands Command Description undebug spanning-tree uplinkfast Disables debugging output. (same as no debug spanning-tree uplinkfast) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-183...
Page 222
The following example shows how to debug the software VLAN events: Switch# debug sw-vlan events vlan manager events debugging is on Switch# Related Commands Command Description undebug sw-vlan (same as no debug Disables debugging output. sw-vlan) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-184 OL-30934-01...
Page 223
To enable the VLAN manager Cisco IOS file system (IFS) error tests, use the debug sw-vlan ifs command. To disable the debugging output, use the no form of this command. debug sw-vlan ifs {open {read | write} | read {1 | 2 | 3 | 4} | write}...
Page 224
Cisco IOS Commands for the Catalyst 4500 Series Switches debug sw-vlan ifs Related Commands Command Description undebug sw-vlan ifs (same as no debug Disables debugging output. sw-vlan ifs) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-186 OL-30934-01...
Page 225
Switch# debug sw-vlan notification modechange vlan manager port mode change notification debugging is on Switch# Related Commands Command Description undebug sw-vlan notification (same as Disables debugging output. no debug sw-vlan notification) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-187...
Page 226
Cisco IOS VTP platform-dependent layer to send. xmit Displays the contents of all outgoing VTP packets that the VTP code will request that the Cisco IOS VTP platform-dependent layer to send; does not include pruning packets. Command Default This command has no default settings.
UDLD packets debugging is on Switch# The following example shows how to debug the UDLD registry events: Switch# debug udld registries UDLD registries debugging is on Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-189...
Page 228
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches debug udld Related Commands Command Description undebug udld (same as no debug udld) Disables debugging output. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-190 OL-30934-01...
Command Description vmps reconfirm (privileged EXEC) Immediately sends VLAN Query Protocol (VQP) queries to reconfirm all the dynamic VLAN assignments with the VLAN Membership Policy Server (VMPS). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-191...
Page 230
The following example shows how to create a multiple-interface macro: Switch(config)# define interface-range macro1 gigabitethernet 4/1-6, fastethernet 2/1-5 Switch(config)# Related Commands Command Description interface range Runs a command on multiple ports at the same time. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-192 OL-30934-01...
Page 231
(Optional) Logs a packet when it matches the access control entry (ACE). Command Default At the end of the ARP access list, there is an implicit deny ip any mac any command. Command Modes arp-nacl configuration mode Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-193...
Page 232
DAI is enabled and to define an ARP access list and applies it to a VLAN. permit Permits an ARP packet based on matches against the DHCP bindings. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-194 OL-30934-01...
When entering the https:// destination URL for the secure server, you must also configure a trustpoint Examples The following example shows how to set the destination to the e-mail address callhome@cisco.com: Switch(config)# call-home Switch(cfg-call-home)# profile cisco Switch(cfg-call-home-profile)# destination address email callhome@cisco.com...
Page 236
Subscribes this destination profile to the Environment alert group. subscribe-to-alert-group inventory Subscribes this destination profile to the Inventory alert group. subscribe-to-alert-group syslog Subscribes this destination profile to the Syslog alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-198 OL-30934-01...
Page 237
Subscribes this destination profile to the Configuration alert group. subscribe-to-alert-group diagnostic Subscribes this destination profile to the Diagnostic alert group. subscribe-to-alert-group environment Subscribes this destination profile to the Environment alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-199...
Page 238
Command Description subscribe-to-alert-group inventory Subscribes this destination profile to the Inventory alert group. subscribe-to-alert-group syslog Subscribes this destination profile to the Syslog alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-200 OL-30934-01...
Page 239
Subscribes to all available alert groups. subscribe-to-alert-group configuration Subscribes this destination profile to the Configuration alert group. subscribe-to-alert-group diagnostic Subscribes this destination profile to the Diagnostic alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-201...
Page 240
Subscribes this destination profile to the Environment alert group. subscribe-to-alert-group inventory Subscribes this destination profile to the Inventory alert group. subscribe-to-alert-group syslog Subscribes this destination profile to the Syslog alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-202 OL-30934-01...
Page 241
Subscribes this destination profile to the Configuration alert group. subscribe-to-alert-group diagnostic Subscribes this destination profile to the Diagnostic alert group. subscribe-to-alert-group environment Subscribes this destination profile to the Environment alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-203...
Page 242
Command Description subscribe-to-alert-group inventory Subscribes this destination profile to the Inventory alert group. subscribe-to-alert-group syslog Subscribes this destination profile to the Syslog alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-204 OL-30934-01...
Page 243
Forward CDP packets to another interface location Enable location information Interface configuration mode Enable application TLV location Enable location information server-location Enable CDP location server on interface Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-205...
Page 244
The following example shows how to create an LLDP filter containing a list of TLVs: Switch> enable Switch# configure terminal Switch(config)# device-sensor filter-list lldp list lldp-list Switch(config-sensor-lldplist)# tlv name mac-phy-config Switch(config-sensor-lldplist)# tlv name system-name Switch(config-sensor-lldplist)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-206 OL-30934-01...
Page 245
Creates a DHCP filter containing a list of options that can be included or dhcp excluded in the Device Sensor output. show device-sensor Displays Device Sensor cache entries. cache Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-207...
Page 246
The following example shows how to create a DHCP filter containing a list of options: Switch> enable Switch# configure terminal Switch(config)# device-sensor filter-list dhcp list dhcp-list Switch(config-sensor-dhcplist)# option name domain-name Switch(config-sensor-dhcplist)# option name host-name Switch(config-sensor-dhcplist)# option number 50 Switch(config-sensor-dhcplist)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-208 OL-30934-01...
Page 247
Creates a CDP or LLDP filter containing a list of options that can be included or excluded in the Device Sensor output. show device-sensor Displays Device Sensor cache entries. cache Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-209...
Page 248
The following example shows how to apply a CDP TLV filter list to the Device Sensor output: Switch> enable Switch# configure terminal Switch(config)# device-sensor filter-spec cdp include cdp-list1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-210 OL-30934-01...
Page 249
Creates a DHCP filter containing a list of options that can be included or dhcp excluded in the Device Sensor output. show device-sensor Displays Device Sensor cache entries. cache Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-211...
Page 250
Enables debugging for Device Sensor. device-sensor filter-list Creates a CDP or LLDP filter containing a list of options that can be included or excluded in the Device Sensor output. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-212 OL-30934-01...
Page 251
Creates a DHCP filter containing a list of options that can be included or dhcp excluded in the Device Sensor output. show device-sensor Displays Device Sensor cache entries. cache Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-213...
Page 252
The following example shows how to configure the SEU behavior as conservative: diagnostic fpga soft-error recover conservative Switch(config)# The following example shows how to revert to the default behavior: no diagnositc fpga soft-error recover Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-214 OL-30934-01...
Related Commands Command Description show diagnostic result module test 2 Displays the module-based diagnostic test results. show diagnostic result module test 3 Displays the module-based diagnostic test results. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-215...
Page 254
1 minute of the test starting, you may see a “TDR test is in progress on interface...” message. Related Commands Command Description show diagnostic content Displays diagnostic content information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-216 OL-30934-01...
Page 255
This command allows you to enter fabric-auto domain configuration mode where you can configure edge devices in the fabric domain. Examples Device(config-fabric-auto)#domain default Device(config-fabric-auto)#domain name exampledomain Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-217...
Page 256
Sets the maximum number of times that the switch will retransmit an EAP-Request/Identity frame to the client before restarting the authentication process. show dot1x Displays 802.1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-218 OL-30934-01...
Page 257
Sets the maximum number of times that the switch will retransmit an EAP-Request/Identity frame to the client before restarting the authentication process. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-219...
Page 258
The following example shows how to enable unidirectional control on incoming packets: Switch(config-if)# dot1x control-direction in Switch(config-if)# Related Commands Command Description show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-220 OL-30934-01...
Page 259
You can verify your settings by entering the show running-config privileged EXEC command. Related Commands Command Description cisp enable Enables Client Information Signalling Protocol (CISP). show cisp Displays CISP information for a specified interface. Refer to IOS documentation. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-221...
Sets the time interval between port reinitializations. dot1x critical vlan Assigns a critically authenticated port to a specific VLAN. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-222 OL-30934-01...
Page 261
Sets the time interval between port reinitializations. dot1x critical vlan Assigns a critically authenticated port to a specific VLAN. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-223...
Page 262
Enables sending EAPOL success packets when a port is critically authorized partway through an EAP exchange. dot1x critical vlan Assigns a critically authenticated port to a specific VLAN. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-224 OL-30934-01...
Page 263
Enables sending EAPOL success packets when a port is critically authorized partway through an EAP exchange. dot1x critical recovery delay Sets the time interval between port reinitializations. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-225...
Page 264
Sets the maximum number of times that the switch will retransmit an EAP-Request/Identity frame to the client before restarting the authentication process. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-226 OL-30934-01...
Page 265
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines With Cisco Release 12.2(25) EWA, you can use the dot1x guest-vlan supplicant command to place an 802.1X-capable host into a guest VLAN. Prior to Cisco Release 12.2(25)EWA, you could only place non-802.1X capable hosts into a guest VLAN.
Page 266
Use the multi-domain keyword to enable MDA on a port. MDA divides the port into both a data domain and a voice domain. MDA allows both a data device and a voice device, such as an IP phone (Cisco or non-Cisco), on the same IEEE 802.1x-enabled port.
Page 267
Switch(config-if)# end Switch# You can verify your settings by entering the show dot1x [interface interface-id] privileged EXEC command. Related Commands Command Description show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-229...
The following example shows how to initialize the 802.1X state machines on an interface: Switch# dot1x initialize Switch# Related Commands Command Description show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-230 OL-30934-01...
Page 269
When re-authentication occurs the MAC address is removed in favor of an 802.1X supplicant, which is detected on the wire. Examples The following example shows how to enable EAP MAC address authentication: Switch(config-if)# dot1x mac-auth-bypass Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-231...
Page 270
The following example shows how to set 5 as the number of times that the switch retransmits an EAP-Request/Identity frame before restarting the authentication process: Switch(config-if)# dot1x max-reauth-req 5 Switch(config-if)# Related Commands Command Description show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-232 OL-30934-01...
Page 271
EAP-Request frame before restarting the authentication process: Switch(config-if)# dot1x max-req 5 Switch(config-if)# The following example shows how to return to the default setting: Switch(config-if)# no dot1x max-req Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-233...
Page 272
Sets the maximum number of times that the switch will retransmit an EAP-Request/Identity frame to the client before restarting the authentication process. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-234 OL-30934-01...
Page 273
EtherChannel, an error message appears, and 802.1X is not enabled. If you enable 802.1X on an inactive port of an EtherChannel, the port does not join the EtherChannel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-235...
Page 274
An enabled status indicates that the port-control value is set either to auto or to force-unauthorized. Related Commands Command Description show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-236 OL-30934-01...
Page 275
Examples The following example shows how to manually reauthenticate the device connected to Gigabit Ethernet interface 1/1: Switch# dot1x re-authenticate interface gigabitethernet1/1 Starting reauthentication on gigabitethernet1/1 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-237...
Page 276
You can verify your settings by entering the show dot1x privileged EXEC command. Related Commands Command Description dot1x timeout Sets the reauthentication timer. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-238 OL-30934-01...
Page 277
The following example shows how to enable 802.1X authentication: Switch(config)# dot1x system-auth-control Switch(config)# Related Commands Command Description dot1x initialize Unauthorizes an interface before reinitializing 802.1X. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-239...
Command History Release Modification 12.1(12)EW This command was introduced on the Catalyst 4500 series switch. 12.2(25)EWA Support for selecting the reauthentication timer from the “server” was added. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-240 OL-30934-01...
Page 279
Switch(config)# interface fastethernet4/3 Switch(config-if)# dot1x timeout reauth-period server Switch(config-if)# end Switch# Related Commands Command Description dot1x initialize Unauthorizes an interface before reinitializing 802.1X. show dot1x Displays dot1x information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-241...
Page 280
Switch(config-netflow-lite-exporter)# exit Switch(config)# Display the exporter Switch# show netflow-lite exporter exporter1 Netflow-lite Exporter exporter1: Network Protocol Configuration: Destination IP address: 5.5.5.6 Source IP Address: 5.5.5.5 VRF label: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-242 OL-30934-01...
Page 281
(netflow-lite exporter submode) options timeout (netflow-lite Specifies an options timeout for the NetFlow-lite collector. exporter submode) export-protocol (netflow-lite Specifies the export protocol for the NetFlow-lite collector. exporter submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-243...
Page 282
Configuring trust mode requires that the port channel exists. If the port channel does not exist, the • following error message is displayed: Router(config-vs-domain)# dual-active trust pagp channel-group 30 Port-channel 30 not configured Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-244 OL-30934-01...
Page 283
Router(config-if)# no shutdown Related Commands Command Description dual-active fast-hello (virtual switch) Configures dual-active detection. show switch virtual (virtual switch) Displays information about dual-active detection configuration and status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-245...
Page 284
Command Description dual-active detection Configure dual-active detection on the virtual switch. (virtual switch) show switch virtual Displays information about dual-active detection configuration and status. (virtual switch) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-246 OL-30934-01...
Page 285
The following example shows how to configure global recovery IP address: Switch(config)# switch virtual domain domain-id Switch(config-vs-domain)# dual-acti ve recovery ip address 192.168.1.5 255.255.255.0 Switch(config-vs-domain)# exit Related Commands Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-247...
Page 286
Command Description dual-active detection (virtual switch) Configure dual-active detection on the virtual switch. show switch virtual (virtual switch) Displays information about dual-active detection configuration and status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-248 OL-30934-01...
Page 287
If the speed is set to 10 or 100, and you do not configure the duplex setting, the duplex mode is set to half duplex. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-249...
Page 288
Configures the interface speed. interface (refer to Cisco IOS Configures an interface. documentation) show controllers (refer to Cisco IOS Displays controller information. documentation) show interfaces Displays interface information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-250 OL-30934-01...
Page 289
If epm access control default is configured and no ACL is downloaded, port ACL is the only ACL on the port. This is how access control functioned prior to Cisco IOS Release 12.2(54)SG. Examples...
Page 290
The erase /all non-default command facilitates the work of a manufacturing facility and repair center. It erases the configuration and states stored in the nonvolatile storage and resets the Catalyst 4500 series switch to the factory default settings. The default settings include those mentioned in the Cisco IOS library as well as those set by the erase /all non-default command (vtp mode=transparent, and the ROMMON variables: ConfigReg=0x2101, PS1= “rommon ! >”...
Page 291
Caution The erase /all non-default command can erase Cisco IOS images in bootflash:. Ensure that a Cisco IOS image can be copied back to the bootflash: (such as, from a accessible TFTP server or a flash card inserted in slot0:) (available on most chassis models), or that the switch can boot from a image stored in an accessible network server.
Page 292
Displays BOOT environment variable information. undelete (refer to Cisco IOS Recovers a file marked “deleted” on a Class a flash file documentation) system. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-254 OL-30934-01...
Enable error detection for the Port Aggregation Protocol (PAgP) flap error-disabled cause. Enable error detection for protocol storm protection security-violation shutdown Enable voice aware 802.1x security. vlan sfp-config-mismatch Enable error detection on an SFP configuration mismatch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-255...
Page 294
This command shows how to globally configure voice aware 802.1x security for per-VLAN error disable: Switch(config)# errdisable detect cause security-violation shutdown vlan You can verify your setting by entering the show errdisable detect privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-256 OL-30934-01...
Page 295
Displays interface status or a list of interfaces in the error-disabled state. clear errdisable interface Clears the error-disabled state from a port or VLAN that was error disabled by the per-VLAN error disable feature. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-257...
(Optional) Enables the ARP inspection cause and recovery timeout. interval interval (Optional) Specifies the time to recover from a specified error-disable cause; valid values are from 30 to 86400 seconds. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-258 OL-30934-01...
Page 298
Displays the error disable detection status. show errdisable recovery Displays error disable recovery timer information. show interfaces status Displays the interface status or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-260 OL-30934-01...
Page 300
Specifies a template data timeout for the NetFlow-lite collector. (netflow-lite exporter submode) options timeout (netflow-lite Specifies an options timeout for the NetFlow-lite collector. exporter submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-262 OL-30934-01...
Page 302
Specifies the average packet size at the observation point. (netflow-lite monitor submode) exporter (netflow-lite monitor Assigns an exporter in netflow-lite monitor submode. submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-264 OL-30934-01...
Page 303
LISP, VLAN, VRF configuration to orchestrate the fabric overlay. The show-running configuration command shows the fabric domain configuration including the and auto-generated base line commands. Examples Device(config)# fabric auto Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-265...
Page 304
Oversubscribed ports (1–12) On WS-X4416-2GB-TX Uplink ports (17–18) Command Modes Interface configuration mode Command History Release Modification 12.1(8a)EW This command was introduced on the Catalyst 4500 series switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-266 OL-30934-01...
Page 305
The following example shows how to enable send flow control: Switch(config-if)# flowcontrol receive on Switch(config-if)# The following example shows how to disable send flow control: Switch(config-if)# flowcontrol send off Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-267...
Page 306
Runs a command on multiple ports at the same time. show flowcontrol Displays the per-interface status and statistics related to flow control. show running-config Displays the running-configuration for a switch. speed Configures the interface speed. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-268 OL-30934-01...
Page 307
Creates an IP ACL (Access Control List). documentation) ipv6 access list (refer to Cisco IOS Creates an IPv6 ACL. documentation) mac access-list extended Defines the extended MAC access lists. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-269...
Page 308
This configuration is auto-generated when you configure a host-pool: ip dhcp relay information option vpn ip dhcp relay information option ip dhcp snooping vlan 10 ip dhcp snooping Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-270 OL-30934-01...
Page 309
192.168.1.0/24 locator-set default.RLOC Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-271...
Page 310
LED off. Switch# hw-module beacon off Switch# *Feb 16 13:12:18.083: %C4K_IOSMODPORTMAN-6-BEACONTURNEDOFF: Beacon has been turned off Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-272 OL-30934-01...
Page 311
4500X-32 10GE (SFP+) WS-C4900X-32P-10G JAE153505E9 10GE SFP+ WS-X4908X-10G-TIM JAE15340C0J M MAC addresses Status --+--------------------------------+---+------------+----------------+--------- 1 0022.bde2.1061 to 0022.bde2.1080 0.2 15.0(1r)SG(0 0.DEV-0 2 0022.bde2.1579 to 0022.bde2.1580 0.1 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-273...
Page 312
Switch# hw-module module 2 start % Module 2 not stopped Related Commands Command Description hw-module module stop Shuts down a module and makes it safe for removal. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-274 OL-30934-01...
Page 313
Module being held in reset WS-X4908X-10G-TIM JAE15340C0J M MAC addresses Status --+--------------------------------+---+------------+----------------+--------- 1 0022.bde2.1061 to 0022.bde2.1080 0.2 15.0(1r)SG(0 0.DEV-0 2 0022.bde2.1579 to 0022.bde2.1580 0.1 In Reset Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-275...
Page 314
Switch# hw-module module 2 stop % Module 2 stopped Related Commands Command Description hw-module module start Boots a module after if it has been stopped. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-276 OL-30934-01...
Page 315
12.2(40)SG Support for TwinGig converter module introduced. Usage Guidelines This command is available on the Cisco Catalyst 4500 modules that support TwinGig converter modules, such as the Supervisor Engine 6-E and WS-X4606-10GE-E. Examples The following example shows how to select Gigabit Ethernet interfaces on a WS-X4606-10GE-E using...
Page 316
The following example shows how to shut off power to a module in slot 5: Switch(config)# no hw-module slot 5 power Related Commands Command Description clear hw-module slot password Clears the password on an intelligent line module. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-278 OL-30934-01...
Page 317
Switch(config)# hw-module system max-port-num-mode 2 A reload of the active supervisor is required to apply the new configuration. After reload, last 3 Line card slots will not be active Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-279...
Page 318
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches hw-module system max-port-num-mode 1/2 Switch(config)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-280 OL-30934-01...
Page 319
1 switch All switches 1 and 2. no hw-module system Restores the default mode (48 ports and 8 Line card slots) for max-port-num-mode 2 switch 1 switch 1. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-281...
Page 320
A 'redundancy reload shelf' or power-cycle of chassis is required to apply the new configuration. After reload, last 3 Line card slots will not be active in Switch 2 Switch(config)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-282 OL-30934-01...
Page 321
(for standalone supervisors) Switch# redundancy reload shelf (for reduandancy supervisors in SSO mode) Switch# redundancy force-switchover (followed by another redundancy force-switchover, for reduandancy supervisors in RPR mode Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-283...
Page 322
The hw-module module x port-group x select gigabitethernet command is blocked in uplink TenGig mode, preventing you from selecting gigabitethernet mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-284 OL-30934-01...
Page 323
(will be Shared-backplane after next reload) A reload of active supervisor is required to apply the new configuration. Related Commands Command Description show hw-module uplink Displays hardware-module uplink information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-285...
Page 324
Similarly, when a Supervisor Engine V-10GE is plugged into a W-C4503, W-4506, or W-4507R chassis, all uplink ports are always available. When a Supervisor Engine V-10GE is plugged into a W-4510R Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-286...
Page 325
Ports Ports Speeds Achievable with this Combination of Pluggables Choose 10-Gigabit operation through the command line interface. SFP+ — — — SFP+ — — — 20 Gbps Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-287...
Page 326
Switch(config)# hw-module uplink select all Warning: This configuration mode may disable slot10. A 'redundancy reload shelf' or power-cycle of chassis is required to apply the new configuration. Switch(config)# exit Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-288 OL-30934-01...
Page 327
If you select the all keyword, only the Drome board will be supported in the tenth slot of the supervisor Note engine. Related Commands Command Description show hw-module uplink Displays hardware-module uplink information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-289...
Page 328
Switch(config-mst)# no instance 2 vlans 40-60 Switch(config-mst)# The following example shows how to move all the VLANs mapped to instance 2 back to the CIST instance: Switch(config-mst)# no instance 2 Switch(config-mst)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-290 OL-30934-01...
Page 329
Sets the MST region name. revision Sets the MST configuration revision number. show spanning-tree mst Displays MST protocol information. spanning-tree mst configuration Enters the MST configuration submode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-291...
Page 330
Chapter 2 Cisco IOS Commands for the Catalyst 4500 Series Switches instance Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-292 OL-30934-01...
Page 331
Supervisor Engine 2 only. vlan VLAN interface; see the interface vlan command. port-channel Port channel interface; see the interface port-channel command. null Null interface; the valid value is 0. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-291...
Page 332
The following example shows how to enter the interface configuration mode on the Fast Ethernet interface 2/4: Switch(config)# interface fastethernet2/4 Switch(config-if)# Related Commands Command Description show interfaces Displays interface information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-292...
Page 333
VLAN interface; see the interface vlan command. port-channel Port channel interface; see the interface port-channel command. null Null interface; the valid value is 0. tunnel Tunnel interface Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-293...
Page 334
1, module 2, port 4: Router(config)# interface gigabitethernet 1/2/4 Router(config)# Related Commands Command Description show interfaces (virtual switch) Displays the traffic that is seen by a specific interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-294...
Page 335
The set ip next-hop verify-availability command can be used with policy-based routing (PBR) to verify next hop reachability to support object tracking using Internet Control Message Protocol (ICMP) ping to verify if a remote device is reachable. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-295...
Page 336
Displays information about objects that are tracked by the tracking process. track Tracks the state of an interface, an ip route, or a response time reporter. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-296...
Page 337
Switch(config)# interface port-channel 64 Switch(config)# Related Commands Command Description channel-group Assigns and configures an EtherChannel interface to an EtherChannel group. show etherchannel Displays EtherChannel information for a channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-297...
You can define up to five port ranges on a single command; separate each range with a comma. When you define a range, you must enter a space between the first port and the hyphen (-): interface range gigabitethernet 5/1 -20, gigabitethernet4/5 -20. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-298...
Page 339
Switch(config-if)# Related Commands Command Description define interface-range Creates a macro of interfaces. show running config (refer to Cisco IOS Displays the running configuration for a switch. documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-299...
The following example shows the output when you enter the interface vlan vlan_id command for a new VLAN number: Switch(config)# interface vlan 23 % Creating new VLAN interface. Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-300...
Page 341
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# ip admission proxy http [success | failure | refresh-all | login] Switch(config)# end Switch# <The new html page is observed.> Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-301...
Switch(config)# ip arp inspection filter static-hosts vlan 1 Switch(config)# end Switch# Switch# show ip arp inspection vlan 1 Source Mac Validation : Enabled Destination Mac Validation : Disabled IP Address Validation : Disabled Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-302...
Page 343
Defines an ARP access list or adds clauses at the end of a predefined list. show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-303...
Page 344
After a switch receives more than the configured rate of packets every second consecutively over a period of burst seconds, the interface is placed into an error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-304...
Page 345
Switch(config-if)# ip arp inspection limit rate 20 burst interval 5 Switch(config-if)# end Related Commands Command Description show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-305...
Page 346
Switch(config)# end Switch# show ip arp inspection log Total Log Buffer Size : 45 Syslog rate : 5 entries per 1 seconds. No entries in log buffer. Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-306...
Page 347
Defines an ARP access list or adds clauses at the end of a predefined list. show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-307...
---------- -------------- Fa6/3 Trusted None Switch# Related Commands Command Description show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-308...
The no form of this command disables only the specified checks. If none of the check options are enabled, all the checks are disabled. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-309...
Page 350
Defines an ARP access list or adds clauses at the end of a predefined list. show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-310...
----------- ------------ Deny Deny Switch# The following example shows how to disable DAI on VLAN 1: Switch# configure terminal Switch(config)# no ip arp inspection vlan 1 Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-311...
Page 352
Defines an ARP access list or adds clauses at the end of a predefined list. show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-312...
• acl-match—Logging on ACL matches is reset to log on deny • dhcp-bindings—Logging on DHCP binding compared is reset to log on deny Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-313...
Page 354
Defines an ARP access list or adds clauses at the end of a predefined list. show ip arp inspection Displays the status of dynamic ARP inspection for a specific range of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-314...
Page 355
Examples The following example shows how to configure the IP CEF load-sharing algorithm that includes Layer 4 ports: Switch(config)# ip cef load-sharing algorithm include-ports Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-315...
Page 356
4 tunneling ports: Switch(config)# ip cef load-sharing algorithm include-ports tunnel Switch(config)# Related Commands Command Description show ip cef vlan Displays the IP CEF VLAN interface status and configuration information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-316...
Page 357
Enables IP source guard on untrusted Layer 2 interfaces. show ip verify source Displays the IP source guard configuration and filters on a particular interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-317...
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-318...
Enables DHCP option 82 data insertion. ip dhcp snooping trust Enables DHCP snooping on a trusted VLAN. ip dhcp snooping vlan Enables DHCP snooping on a VLAN or a group of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-319...
Page 360
Chapter 2 ip dhcp snooping binding Command Description show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-320...
When a file is stored in a remote location accessible through TFTP, an RPR/SSO standby supervisor engine can take over the binding list when a switchover occurs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-321...
Page 362
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-322...
The following example shows how to enable DHCP Snooping on VLAN 500 through 555 and option 82 remote ID: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# ip dhcp snooping Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-323...
Page 364
VLAN. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-324...
Page 365
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-325...
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-326...
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-327...
Switch(config)# ip dhcp snooping vlan 10 55 Switch(config)# The following example shows how to disable DHCP snooping on a group of VLANs: Switch(config)# no ip dhcp snooping vlan 10 55 Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-328...
Page 369
VLAN. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-329...
Page 370
Switch(config)# ip dhcp snooping vlan 500 555 Switch(config)# ip dhcp snooping information option format remote-id string switch123 Switch(config)# interface GigabitEthernet 5/1 Switch(config-if)# ip dhcp snooping trust Switch(config-if)# ip dhcp snooping limit rate 100 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-330...
Page 371
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-331...
Switch(config-if)# ip igmp filter 22 Switch(config-if)# Related Commands Command Description ip igmp profile Creates an IGMP profile. show ip igmp profile Displays all configured IGMP profiles or a specified IGMP profile. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-332...
Page 373
The following example shows how to limit the number of IGMP groups that an interface can join to 25: Switch(config)# interface gigabitethernet1/1 Switch(config-if)# ip igmp max-groups 25 Switch(config-if) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-333...
IP multicast groups by applying an IGMP profile to the interface. show ip igmp profile Displays all configured IGMP profiles or a specified IGMP profile. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-334...
Page 375
Note Examples The following example shows how to change the frequency at which the designated switch sends the IGMP host-query messages: Switch(config-if)# ip igmp query-interval 120 Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-335...
Page 376
Displays the multicast groups with receivers that are documentation) directly connected to the router and that were learned through Internet Group Management Protocol (IGMP), use the show ip igmp groups command in EXEC mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-336...
The following example shows how to enable IGMP snooping: Switch(config)# ip igmp snooping Switch(config)# The following example shows how to disable IGMP snooping: Switch(config)# no ip igmp snooping Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-337...
Page 378
Configures a Layer 2 interface as a multicast router interface for a VLAN. ip igmp snooping vlan static Configures a Layer 2 interface as a member of a group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-338...
Page 379
IGMP snooping mrouter learn mode is pim-dvmrp on this Vlan IGMP snooping is running in IGMP_ONLY mode on this Vlan IGMP snooping report suppression is enabled on this Vlan Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-339...
Page 380
Configures a Layer 2 interface as a multicast router interface for a VLAN. ip igmp snooping vlan static Configures a Layer 2 interface as a member of a group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-340...
Configures a Layer 2 interface as a multicast router interface for a VLAN. ip igmp snooping vlan static Configures a Layer 2 interface as a member of a group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-341...
Page 382
Enables IGMP immediate-leave processing. ip igmp snooping vlan mrouter Configures a Layer 2 interface as a multicast router interface for a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-342...
Page 383
Command Description ip igmp snooping vlan static Configures a Layer 2 interface as a member of a group. show ip igmp snooping membership Displays host membership information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-343...
Page 384
Configures a Layer 2 interface as a multicast router interface for a VLAN. ip igmp snooping vlan static Configures a Layer 2 interface as a member of a group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-344...
Page 385
Command Description show ip igmp interface Displays the information about the IGMP-interface status and configuration. show mac-address-table multicast Displays information about the multicast MAC address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-345...
This command was introduced on the Catalyst 4500 series switch. 12.1(12c)EW Support for extended addressing was added. 12.2(25)EW Support for the 10-Gigabit Ethernet interface was introduced on the Catalyst 4500 series switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-346...
Page 387
Displays information on dynamically learned and manually configured VLAN switch interfaces. show ip igmp snooping mrouter Displays information on the dynamically learned and manually configured multicast switch interfaces. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-347...
Configuring port FastEthernet5/11 on group 0100.5e02.0203 vlan 4 Switch(config)# Related Commands Command Description ip igmp snooping Enable IGMP snooping. ip igmp snooping vlan immediate-leave Enable IGMP immediate-leave processing. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-348...
Page 389
Configures a Layer 2 interface as a multicast router interface for a VLAN. show mac-address-table multicast Displays information about the multicast MAC address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-349...
Page 390
ICMP redirect is disabled on interfaces where the local proxy ARP feature is enabled. Examples The following example shows how to enable the local proxy ARP feature: Switch(config-if)# ip local-proxy-arp Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-350...
Clears all the MFIB fast-drop entries. show ip mfib fastdrop Displays all currently active fast-drop entries and shows whether fast drop is enabled. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-351...
Page 392
S-hash algorithm. When the ip multicast multipath command is configured and multiple equal-cost paths exist, the path in which Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-352...
Page 393
The following example shows how to enable ECMP multicast load splitting on a router based on source, group, and next-hop address using the next-hop-based S-G-hash algorithm: Switch(config)# ip multicast multipath s-g-hash next-hop-based Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-353...
Page 394
Switch(config)# ip name-server 192.0.2.1 192.0.2.2 The following example shows how to specify IPv6 hosts 3FFE:C00::250:8BFF:FEE8:F800 and 2001:0DB8::3 as the name servers: Switch(config)# ip name-server 3FFE:C00::250:8BFF:FEE8:F800 2001:0DB8::3 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-354...
Page 395
This action is done to avoid having flows with and without inferred fields in the cache simultaneously. For additional information on NetFlow switching, refer to the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide.
Page 396
The following example shows how to enable NetFlow switching on the switch: Switch# config terminal Switch(config)# ip route-cache flow Switch(config)# exit Switch# This command does not work on individual interfaces. Note Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-356...
Switch(config)# ip source binding 11.0.0.1 0000.000A.000B vlan 10 interface fastethernet6/10 Switch(config)# Related Commands Command Description show ip source binding Displays IP source bindings that are configured on the system. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-357...
Page 398
The following example shows how to disable sticky ARP: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config) no ip sticky-arp Switch(config)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-358...
Page 399
Enables Address Resolution Protocol (ARP) entries for static routing over the Switched Multimegabit Data Service (SMDS) network. show arp (refer to Cisco IOS Displays ARP information. documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-359...
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines This command does not apply to Layer 3-switched (routed) packets. The Catalyst 4500 series switch checks the validity of the following fields in the IPv4 header for all switched IPv4 packets: The version must be 4.
Switch# show ip verify source interface f6/1 Interface Filter-type Filter-mode IP-address Mac-address Vlan --------- ----------- ----------- --------------- ----------------- ---------- Fa6/1 ip-mac active 10.0.0.1 Fa6/1 ip-mac active deny-all 11-20 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-361...
Page 402
Displays IP source bindings that are configured on the system. show ip verify source Displays the IP source guard configuration and filters on a particular interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-362...
Page 403
The following example shows how to enable unicast RPF exist-only checking mode: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface gigabitethernet1/1 Switch(config-if)# ip verify unicast source reachable-via rx allow-default Switch(config-if)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-363...
Page 404
Related Commands Command Description ip cef (refer to Cisco IOS documentation) Enables Cisco Express Forwarding (CEF) on the switch. show running-config Displays the current running configuration for a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 405
7 for proprietary. The password argument can be up to eight characters in length. Command Default WCCP services are not enabled on the router. Command Modes Global configuration (config) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-365...
Page 406
The default is for no group list to be configured, in which case all cache engines may participate in the service group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-366...
Page 407
Enables all WCCP services. ip wccp version Specifies which version of WCCP you wish to use on your router. show ip wccp Displays global statistics related to WCCP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-367...
Page 408
The vrf vrf-name keyword and argument pair is optional. It allows you to specify a VRF to associate with a service group. You can then specify a web-cache service name or service number. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-368...
Page 409
Switch(config-if)# ipv6 wccp vrf abc 92 redirect in Switch(config)# interface vlan 50 Switch(config-if)# vrf forwarding abc Related Commands Command Description show ipv6 wccp Displays global statistics related to WCCP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-369...
Page 410
The priority of a WCCP service group is determined by the web cache appliance. The priority of a WCCP Note service group cannot be configured via Cisco IOS software. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-370...
Page 411
Configure an interface to exclude packets received on an interface from being checked for redirection. ip wccp version Specifies which version of WCCP you wish to use on your router. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-371...
Page 412
The following example shows how to enable the multicast packets for a web cache with a multicast address of 224.1.1.100: Switch# configure terminal Switch(config)# ip wccp web-cache group-address 224.1.1.100 Switch(config)# interface gigabitethernet 3/1 Switch(config-if)# ip wccp web-cache group-listen Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-372...
Page 413
Configures an interface to exclude packets received on an interface from being checked for redirection. ip wccp version Specifies which version of WCCP you wish to use on your router. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-373...
Page 414
Identification number of the cache engine service group; valid values are from 0 to 254. If Cisco cache engines are used in the cache cluster, the reverse proxy service is indicated by a value of 99. Specifies packet redirection on an inbound interface.
Page 415
Examples The following example shows how to configure a session in which reverse proxy packets on Ethernet interface 3/1 are being checked for redirection and redirected to a Cisco Cache Engine: Switch(config)# ip wccp 99 Switch(config)# interface gigabitethernet 3/1...
Page 416
Enable packet redirection on an inbound or outbound interface using Web Cache Communication Protocol (WCCP). ip wccp redirect out Configures redirection on an interface in the outgoing direction. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-376...
Page 417
Enables redirection exclusion on an interface. show ip interface Displays the usability status of interfaces that are configured for IP. show ip wccp Displays the WCCP global configuration and statistics. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-377...
Page 418
Related CommandsT Command Description ipv6 dhcp relay destination Specifies a destination address to which client messages are forwarded and to enable DHCPv6 relay service on the interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-378...
Page 419
Related Commands Command Description ipv6 dhcp-ldra Enables LDRA functionality on an access node. ipv6 dhcp ldra attach-policy (VLAN) Specifies a VLAN number and enters VLAN configuration mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-379...
Page 420
The following example shows how to enable LDRA functionality on an interface and specify it as server facing: Device> enable Device# configure terminal Device(config)# ipv6 dhcp-ldra enable Device(config)# interface gigabitethernet 0/0 Device(config-if)# switchport Device(config-if)# ipv6 dhcp-ldra attach-policy server-facing Device(config-if)# exit Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-380...
Page 421
Related Commands Command Description ipv6 dhcp-ldra Enables LDRA functionality on an access node. ipv6 dhcp ldra attach-policy (VLAN) Enables LDRA functionality on a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-381...
Page 422
Command History Release Modification Cisco IOS This command was introduced on the Catalyst 4500 series switches in a release Release 15.2(5)E2 prior to Cisco IOS Release 15.2(5)E2. Usage Guidelines You need to configure the LDRA functionality globally using the ipv6 dhcp-ldra command before configuring it on a VLAN.
Page 423
Chapter 2 ipv6 dhcp lrda attach-policy (VLAN) Related Commands Command Description ipv6 dhcp-lrda Enables LDRA functionality on an access node. vlan configuration Enables SNMP MAC address notifications. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-383...
Page 424
Command History Release Modification Cisco IOS This command was introduced on the Catalyst 4500 series switches in a release Release 15.2(5)E2 prior to Cisco IOS Release 152(5)E2. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-384...
Page 425
Device(config-if)# ipv6 dhcp relay destination FE80::250:A2FF:FEBF:A056 gigabitethernet 4/3 Related Commands Command Description interface Configures an interface and enters interface configuration mode. ipv6 dhcp-ldra Enables LDRA functionality on an access node. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-385...
The following example shows how to globally enable MLD snooping: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# ipv6 mld snooping Switch(config)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-386...
Page 427
You can verify your settings by entering the show ipv6 mld snooping user EXEC command. Related Commands Command Description show ipv6 mld snooping Displays IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping configuration of the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-387...
Page 428
When the VLAN count is not configured (set to the default of 0), the global count is used. VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-388...
Page 429
(MLD) snooping configuration of the switch or the VLAN. show ipv6 mld snooping querier Displays IP version 6 (IPv6) MLD snooping querier-related information most recently received by the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-389...
Page 430
0, the global value is used. VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-390...
Page 431
Displays IP version 6 (IPv6) MLD snooping querier-related information most recently received by the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-391...
Page 432
Enables IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping globally or on the specified VLAN. show ipv6 mld snooping Displays IP version 6 (IPv6) MLD snooping configuration of the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-392...
Page 433
0 (the default), the global value is used. VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-393...
Page 434
Displays IP version 6 (IPv6) MLD snooping configuration of the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-394...
You can verify your settings by entering the show ipv6 MLD snooping [vlan vlan-id] user EXEC command. Related Commands Command Description show ipv6 mld snooping Displays IP version 6 (IPv6) MLD snooping configuration of the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-395...
The configuration and the static ports and groups are saved in NVRAM. VLAN numbers 1002 through 1005 are reserved for Token Ring and FDDI VLANs and cannot be used in MLD snooping. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-396...
Page 437
Enables IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping globally or on the specified VLAN. show ipv6 mld snooping Displays IP version 6 (IPv6) MLD snooping configuration of the switch or the VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-397...
Page 438
To cancel the ISSU upgrade or the downgrade process in progress and to restore the Catalyst 4500 series switch to its state before the start of the process, use the issue abortversion command. issu abortversion active-slot [active-image-new]...
Page 439
Displays the ISSU state and current booted image name during the ISSU process. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-399...
Page 440
Chapter 2 issu acceptversion issu acceptversion To halt the rollback timer and to ensure that the new Cisco IOS software image is not automatically stopped during the ISSU process, use the issu acceptversion command. issu acceptversion active-slot [active-image-new] Syntax Description active-slot Specifies the slot number for the currently active supervisor engine.
Page 441
Configures the In Service Software Upgrade (ISSU) rollback timer value. show issu state Displays the ISSU state and current booted image name during the ISSU process. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-401...
Page 442
Chapter 2 issu commitversion issu commitversion To load the new Cisco IOS software image into the new standby supervisor engine, use the issu commitversion command. issu commitversion standby-slot [standby-image-new] Syntax Description standby-slot Specifies the slot number for the currently active supervisor engine.
Page 443
Displays the ISSU state and current booted image name during the ISSU process. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-403...
Page 444
The issu loadversion command causes the standby supervisor engine to be reset and booted with the new Cisco IOS software image specified by the command. If both the old image and the new image are ISSU capable, ISSU compatible, and have no configuration mismatches, the standby supervisor engine moves into Stateful Switchover (SSO) mode, and both supervisor engines move into the load version (LV) state.
Page 445
Displays the ISSU state and current booted image name during the ISSU process. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-405...
Page 446
Halts the rollback timer and ensures that the new Cisco IOS software image is not automatically stopped during the ISSU process. issu commitversion Loads the new Cisco IOS software image into the new standby supervisor engine. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-406...
Page 447
Chapter 2 issu runversion Command Description issu loadversion Starts the ISSU process. show issu state Displays the ISSU state and current booted image name during the ISSU process. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-407...
Page 448
Halts the rollback timer and ensures that the new Cisco IOS software image is not automatically stopped during the ISSU process. issu set rollback-timer Configures the In Service Software Upgrade (ISSU) rollback timer value. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-408...
Page 449
Examples The following example shows how to enable protocol tunneling for the CDP packets: Switch(config terminal)# key chain mac_chain macsec Switch(config-keychain-macsec)# Related Commands Command Description Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-409...
Page 450
To enable protocol tunneling on an interface, use the l2protocol-tunnel command. You can enable tunneling for the Cisco Discovery Protocol (CDP), Spanning Tree Protocol (STP), or VLAN Trunking Protocol (VTP) packets. To disable tunneling on the interface, use the no form of this command.
Page 451
Sets a drop threshold for the maximum rate of Layer 2 protocol packets per second to be received before an interface drops packets. l2protocol-tunnel shutdown-threshold Configures the protocol tunneling encapsulation rate. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-411...
Page 452
Sets a drop threshold for the maximum rate of Layer 2 protocol packets per second to be received before an interface drops packets. l2protocol-tunnel shutdown-threshold Configures the protocol tunneling encapsulation rate. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-412...
Page 453
I2protocol-tunnel drop-threshold command. You can set the drop threshold for the Cisco Discovery Protocol (CDP), Spanning Tree Protocol (STP), or VLAN Trunking Protocol (VTP) packets. To disable the drop threshold on the interface, use the no form of this command.
Page 454
Enables protocol tunneling on an interface. l2protocol-tunnel cos Configures the class of service (CoS) value for all tunneled Layer 2 protocol packets. l2protocol-tunnel shutdown-threshold Configures the protocol tunneling encapsulation rate. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-414...
Page 455
To configure the protocol tunneling encapsulation rate, use the I2protocol-tunnel shutdown-threshold command. You can set the encapsulation rate for the Cisco Discovery Protocol (CDP), Spanning Tree Protocol (STP), or VLAN Trunking Protocol (VTP) packets. To disable the encapsulation rate on the interface, use the no form of this command.
Page 456
The following example shows how to specify a minimum of three active LACP ports before port channel 2 becomes active: Switch(config(#) interface port-channel 2 Switch(config-if)# port-channel min-links 3 Related Commands Command Description show lacp Displays LACP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-416...
Page 457
Assigns and configure an EtherChannel interface to an EtherChannel group. channel-protocol Enables LACP or PAgP on an interface. lacp system-priority Sets the priority of the system for LACP. show lacp Displays LACP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-417...
Page 458
The following example shows how to set the lacp rate for an interface: Examples Switch(config)# interface gigabitEthernet 2/1 Switch(config-if)# lacp rate fast Related Commands Command Description show lacp Displays LACP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-418...
Page 459
Assigns and configure an EtherChannel interface to an EtherChannel group. channel-protocol Enables LACP or PAgP on an interface. lacp system-priority Sets the priority of the system for LACP. show lacp Displays LACP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-419...
Page 460
Use this command to activate PRTU licenses that are inactive. Downloading the license file from cisco portal and installing the license are not required. The PRTU licenses are bundled with image. Because the PRTU license is of highest precedence, when the PRTU license is activated, other license of the same feature switch to inactive state.
Page 461
Else, the deactivation will fail. Examples The following example shows how to deactivate PRTU licenses: Switch# license right-to-use deactivate entservices Related Commands Command Description Activates the PRTU license license right-to-use activate Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-421...
Related Commands Command Description link state track Configures the link state group and enables link state tracking. show link state group Displays the link state group information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-422...
Configures the link state group and the interface as either an upstream or downstream interface in the group. show link state group Displays the link state group information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-423...
Page 464
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# int gi 3/1 Switch(config-if)# lldp tlv-select power-management Related Commands Command Description lldp run Cisco IOS Command Reference library. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-424...
Page 465
End with CNTL/Z. Switch(config)# logging event link-status global Switch(config)# end Switch# Related Commands Command Description logging event link-status (interface Enables the link-status event messaging on an interface. configuration) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-425...
Page 466
The following example shows how to turn off logging event link status regardless of the global setting: Switch# config terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface gi11/1 Switch(config-if)# no logging event link-status Switch(config-if)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-426...
Page 467
Switch(config-if)# logging event link-status use-global Switch(config-if)# end Switch# Related Commands Command Description logging event link-status global (global Changes the default switch-wide global link-status event configuration) messaging settings. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-427...
Page 468
End with CNTL/Z. Switch(config)# logging event trunk-status global Switch(config)# end Switch# Related Commands Command Description logging event trunk-status global Enables the trunk-status event messaging on an interface. (global configuration) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-428...
Page 469
The following example shows how to turn off logging event trunk status regardless of the global setting: Switch# config terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface gi11/1 Switch(config-if)# no logging event trunk-status Switch(config-if)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-429...
Page 470
Switch(config)# interface gi11/1 Switch(config-if)# logging event trunk-status use-global Switch(config-if)# end Switch# Related Commands Command Description logging event trunk-status global Enables the trunk-status event messaging on an interface. (global configuration) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-430...
Page 471
The following example shows how to enable and configure MAB on a port: Switch(config-if)# mab eap Switch(config-if)# The following example shows how to disable MAB on a port: Switch(config-if)# no mab Switch(config-if)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-431...
Page 472
Chapter 2 Related Commands Command Description show authentication Displays Authentication Manager information. show mab Displays MAB information. show running-config Displays the running configuration information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-432...
Page 473
Specifies any source-host or destination-host. arbitrary ethertype (Optional) Specifies an arbitrary ethertype in the range 1536 to 65535 (Decimal or Hexadecimal) deny Prevents access if the conditions are matched. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-433...
Page 474
Mapping an Ethernet Packet to a Protocol Family Protocol Family Ethertype in Packet Header Appletalk 0x809B, 0x80F3 Arp-Non-Ipv4 0x0806 and protocol header of Arp is a non-Ip protocol family Decnet 0x6000-0x6009, 0x8038-0x8042 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-434...
Page 475
Switch(config-ext-macl)# deny 0000.4700.0001 0.0.0 0000.4700.0009 0.0.0 protocol-family appletalk Switch(config-ext-macl)# permit any any Switch(config-ext-macl)# end Switch# Related Commands Command Description show vlan access-map Displays VLAN access map information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-435...
Page 476
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines When a virtual switch boots, the router MAC address is derived from the Cisco pool of virtual switch specific MAC addresses. The router address is used as the common router MAC address for interfaces on both the active and the standby chassis.
Page 477
Router(config)# switch virtual domain test-mac-address Router(config-vs-domain)# mac-address use-virtual Router(config-vs-domain)# Related Commands Command Description switch virtual domain (virtual switch) Assigns a switch number and enters virtual switch domain configuration submode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-437...
Page 478
Switch(config)# The following example shows how to disable aging: Switch(config)# mac-address-table aging-time 0 Switch(config) Related Commands Command Description show mac-address-table aging-time Displays MAC address table aging information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-438...
Page 479
GigabitEthernet3/1 0003.3178.ec0a dynamic assigned GigabitEthernet3/1 0003.4700.24c3 dynamic ip GigabitEthernet3/1 0003.4716.f475 dynamic ip GigabitEthernet3/1 0003.4748.75c5 dynamic ip GigabitEthernet3/1 0003.47f0.d6a3 dynamic ip GigabitEthernet3/1 0003.47f6.a91a dynamic ip GigabitEthernet3/1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-439...
Page 482
If you disable MAC address learning on a VLAN that includes a secure port, MAC address learning is not disabled on the secure port. If you later disable port security on the interface, the disabled MAC address learning state is enabled. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-442...
Page 483
Switch(config)# no mac-address-table learning vlan 2003 Related Commands Command Description show mac address-table learning Displays the MAC address learning status on all VLANs or on the specified VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-443...
Page 484
The default limit is 50 percent. The default time is 120 seconds. Hardware MAC learning failure syslog notification is disabled. The default limit is 1000. The default interval is 150 seconds. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-444...
Page 485
Clears the global counter entries from the Layer 2 MAC address table. mac-address-table notification Enables MAC address notification on a switch. snmp-server enable traps Enables SNMP notifications. snmp trap mac-notification change Enables SNMP MAC address notifications. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-445...
Page 486
The following example shows how to add the static entries to the MAC address table: Switch(config)# mac-address-table static 0050.3e8d.6400 vlan 100 interface fastethernet5/7 Switch(config)# Related Commands Command Description show mac-address-table static Displays the static MAC address table entries only. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-446...
Page 487
Chapter 2 macro apply cisco-desktop macro apply cisco-desktop To enable the Cisco-recommended features and settings that are suitable for connecting a switch port to a standard desktop, use the macro apply cisco-desktop command. macro apply cisco-desktop $AVID access_vlanid Syntax Description $AVID access_vlanid Specifies an access VLAN ID.
Page 488
Enables the Cisco-recommended features and settings that are suitable for connecting a switch port to another switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-448...
Page 489
Engine 8-E, and on Cisco Catalyst 4500-X series switches. Usage Guidelines This command cannot be used to configure multi-point to multi-point links. Examples The following example shows how to enable the Cisco-recommended features and settings on port fa2/1: Switch(config)# interface FastEthernet2/1 Switch(config-if)# macsec network-link Switch(config-if)# exit Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 490
Cisco IOS XE 3.9.0E This command was introduced on Cisco Catalyst 4500-E with Supervisor Engine 8-E, and on Cisco Catalyst 4500-X series switches. Examples The following example shows how to enable the Cisco-recommended features and settings on port fa2/1: Switch(config)# interface FastEthernet2/1 Switch(config-if)# mka pre-shared-key key-chain kc1 Switch(config-if)# exit Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex...
Page 491
Global Configuration Command History Release Modification Cisco IOS XE 3.9.0E This command was introduced on Cisco Catalyst 4500-E with Supervisor Engine 8-E, and on Cisco Catalyst 4500-X series switches. Examples The following example shows how to configure MKA policy options:...
Page 492
To enable the Cisco-recommended features and settings that are suitable for connecting a switch port to a standard desktop and a Cisco IP phone, use the macro apply cisco-phone command. macro apply cisco-phone $AVID access_vlanid $VVID voice_vlanid...
Page 493
Enables the Cisco-recommended features and settings that are suitable for connecting a switch port to another switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-453...
Page 494
Chapter 2 macro apply cisco-router macro apply cisco-router To enable the Cisco-recommended features and settings that are suitable for connecting a switch port to a router, use the macro apply cisco-router command. macro apply cisco-router $NVID native_vlanid Syntax Description $NVID native_vlanid Specifies a native VLAN ID.
Page 495
Enables the Cisco-recommended features and settings that are suitable for connecting a switch port to another switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-455...
Page 496
Chapter 2 macro apply cisco-switch macro apply cisco-switch To enable the Cisco-recommended features and settings that are suitable for connecting a switch port to another switch, use the macro apply cisco-switch command. macro apply cisco-switch $NVID native_vlanid Syntax Description $NVID native_vlanid Specifies a native VLAN ID.
Page 497
Cisco IP phone. macro apply cisco-router Enables the Cisco-recommended features and settings that are suitable for connecting a switch port to a router. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-457...
Page 498
Changes built-in function default values or to map user-defined function) triggers to built-in functions, and to pass the parameter values. macro auto execute Maps a trigger to a remotely defined functions. (remotely-defined trigger) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-458...
Page 499
Enables Auto SmartPorts macros on a specific interface. macro auto sticky Specifies not to remove configurations applied by ASP across link flaps and device removal. shell trigger Creates a user defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-459...
Page 500
(Optional) Specifies values for the parameters that are to be used in the function body. Command Default Auto Smartports is disabled. Command Modes Global configuration Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-460...
Page 501
Examples The following example shows how to use two built-in Auto Smartports macros for connecting Cisco switches and Cisco IP phones to the switch. It modifies the default voice VLAN, access VLAN, and native VLAN for the trunk interface: Switch# configure terminal...
Page 502
Enables Auto SmartPorts macros on a specific interface. macro auto sticky Specifies not to remove configurations applied by ASP across link flaps and device removal. shell trigger Creates a user defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-462...
Page 503
Maps a trigger to a user-defined function. (user-defined function) macro auto global processing Enables Auto Smartports on a switch. macro auto processing Enable Auto SmartPorts macros on a specific interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-463...
Page 504
(remotely-defined trigger) Command Description macro auto sticky Specifies not to remove configurations applied by ASP across link flaps and device removal. shell trigger Create a user defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-464...
Page 505
Examples The following example shows how to map the user-defined event trigger Cisco Digital Media Player (DMP) to a user-defined macro. Connect the DMP to an 802.1x- or MAB-enabled switch port.
Page 506
Enables Auto SmartPorts macros on a specific interface. macro auto sticky Specifies not to remove configurations applied by ASP across link flaps and device removal. shell trigger Creates a user defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-466...
Page 507
When the switch detects a new device on a port it applies the appropriate ASP macro. When a link-down event occurs on a port, the switch removes the macro. For example, when you connect a Cisco IP phone to a port, ASP automatically applies the IP phone macro. The IP phone macro enables quality of service (QoS), security features, and a dedicated voice VLAN to ensure proper treatment of delay-sensitive voice traffic.
Page 508
Chapter 2 macro auto global processing When using 802.1X or MAB authentication, configure the RADIUS server to support the Cisco attribute-value (AV) pair auto-smart-port=event trigger. When CDP-identified devices advertise multiple capabilities, a switch chooses a capability in this priority order: switch, router, access point, lightweight access point, phone, host.
Page 509
Enables Auto SmartPorts macros on a specific interface. macro auto sticky Specifies not to remove configurations applied by ASP across link flaps and device removal. shell trigger Creates a user defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-469...
Page 510
Displays the devices connected to a switch, along with their properties and classifications. show macro auto monitor type Displays all the device types known to the device classification agent. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-470...
Page 511
Configures mapping from an event trigger to a built-in macro. function) shell trigger Creates a user defined trigger. show shell functions Displays configurations included for all the builtin functions including user created and built-in functions. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-471...
Page 512
Maps a trigger to a remotely defined functions. (remotely-defined trigger) macro auto execute Maps a trigger to a user-defined function. (user-defined function) macro auto global processing Enables Auto Smartports on a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-472...
Page 513
Enables Auto Smartports on a switch. macro auto processing Enables Auto SmartPorts macros on a specific interface. shell trigger Creates a user defined trigger. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-473...
Page 514
Chapter 2 macro global apply cisco-global macro global apply cisco-global To apply the system-defined default template to the switch, use the macro global apply cisco-global global configuration command on the switch stack or on a standalone switch. macro global apply cisco-global Syntax Description This command has no keywords or variables.
Page 515
Applies the system-defined default template to the switch. macro global description Enters a description about the macros that are applied to the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-475...
You can verify your settings by entering the show parser macro description privileged EXEC command. Related Commands Command Description macro global apply cisco-global Applies the system-defined default template to the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-476...
Page 517
Command History Release Modification 12.1(12c)EW This command was introduced on the Catalyst 4500 series switch. (Catalyst 4507R only). Usage Guidelines The main CPU submode is used to manually synchronize the configurations on the two supervisor engines. From the main CPU submode, use the...
Page 518
The MAC sequence is not effective for IP packets. IP packets should be access controlled by IP match clauses. Refer to the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide for additional configuration guidelines and restrictions. Refer to the Cisco IOS Command Reference publication for additional match command information.
Page 519
Related Commands Command Description show vlan access-map Displays the contents of a VLAN access map. vlan access-map Enters VLAN access-map command mode to create a VLAN access map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-479...
Page 520
Command Default No match criteria are defined. Command Modes Class-map configuration mode Command History Release Modification 12.1(8a)EW This command was introduced on the Catalyst 4500 series switches. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-480...
Page 521
Switch(config-cmap)# match ip precedence 5 6 7 Switch(config-cmap)# exit Switch# The following example shows how to delete the IP-precedence match criteria and to classify traffic using acl1: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-481...
Page 522
Creates a class map to be used for matching packets to the class whose name you specify and to enter class-map configuration mode. show class-map Displays class map information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-482...
Page 523
To attach a flow-based policy map as a child to an aggregate policy map, use the service-policy command. The match flow command is available on the Catalyst 4500 series switch only when Note Supervisor Engine 6-E or 6L-E is present.
Page 525
Switch(config-cmap)# match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port Switch(config-cmap)# exit Switch(config)# policy-map p1 Switch(config-pmap)# class c1 Switch(config-pmap-c)# police 1000000 9000 Switch(config-pmap-c)# exit Switch(config-pmap)# exit Switch(config)# interface fastEthernet 6/1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-485...
Page 526
Displays information about the policy map. show policy-map interface Displays the statistics and configurations of the input and output policies that are attached to an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-486...
Examples The following example shows how to enable auto MDIX on a port: Switch# configure terminal Switch(config)# interface FastEthernet6/3 Switch(config-if)# speed auto Switch(config-if)# mdix auto Switch(config-if)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-487...
Page 528
Displays traffic on a specific interface. show interfaces (virtual Displays the interface capabilities for an interface or for all the switch) interfaces on a switch. show interfaces status Displays the interface status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-488...
Page 529
Examples The following example shows how to configure port 5/45 on a WS-X4948 chassis to use the RJ-45 connector: Switch(config)# interface gigabitethernet 5/45 Switch(config-if)# media-type rj45 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-489...
Page 530
Specifies SSO mode. Command Default If you are upgrading the current supervisor engine from Cisco IOS Release 12.2(18)EW or an earlier release to 12.2(20)EWA, and the RPR mode has been saved to the startup configuration, both supervisor engines will continue to operate in RPR mode after the software upgrade. To use SSO mode, you must manually change the redundancy mode to SSO.
Page 531
Forces a switchover from the active to the standby supervisor engine. show redundancy Displays redundancy facility information. show running-config Displays the running configuration of a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-491...
Page 532
The following example shows how to define a core system filter using an existing ACL or class-map: Switch# monitor capture mycap filter access-list myacl Switch# monitor capture mycap filter class-map mycm Switch# no monitor capture mycap filter class-map mycm Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-492...
Page 533
Examples The following example shows how to associate or disassociate a capture file: Switch# monitor capture mycap export bootflash:mycap.pcap Switch# monitor capture mycap clear Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-493...
Page 534
Switch# monitor capture mycap interface gigabitEthernet 3/1 in The following example shows how to remove an attachment point: Switch# no monitor capture mycap interface gigabitEthernet 3/1 in Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-494...
Page 535
The size of the capture file can be limited with the size option. The file location must one of the following: • Internal bootflash (bootflash: ) • External flash (slot0: ) USB (usb0: ) • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-495...
Page 536
Frame Number: 1 Frame Length: 256 bytes (2048 bits) Capture Length: 256 bytes (2048 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:ip:udp:data] Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-496...
Page 542
[Time since reference or first frame: 0.000000000 seconds] Frame Number: 1 Frame Length: 256 bytes (2048 bits) Capture Length: 256 bytes (2048 bits) [Frame is marked: False] Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-502...
Page 543
%Display-filter cannot be specified when capture is associated to a file. Ignoring display filter% A file by the same capture file name already exists, overwrite?[confirm] 0.000000 10.1.1.117 -> 20.1.1.2 UDP Source port: 20001 Destination port: 20002 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-503...
(Optional) Specifies dot1q encapsulation. ingress (Optional) Indicates whether the ingress option is enabled. vlan vlan_id (Optional) Specifies the VLAN; valid values are from 1 to 4094. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-506...
Page 547
Specifies packets with the a high priority. Specifies packets with the a medium priority. Specifies packets with the a low priority. ucast-rpf-fail Specifies IPv4/IPv6 Unicast RPF failures. (Optional) all queues. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-507...
Page 548
Packets are transmitted untagged out the destination port; ingress and learning are disabled. All packets are permitted and forwarded “as is” on the destination port. Command Modes Global configuration mode Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-508...
Page 549
You must first remove a SPAN destination interface before changing the SPAN destination to a different interface. Beginning in Cisco IOS Release 12.1(12c)EW, you can configure sources from different directions within a single user session. Note Beginning in Cisco IOS Release 12.1(12c)EW, SPAN is limited to two sessions containing...
Page 550
Switch(config)# monitor session 3 source cpu queue 10 rx Switch(config)# end control-packet is mapped to queue 10. Note Related Commands Command Description show monitor Displays information about the SPAN session. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-510...
Page 551
The following example shows how to specify an MTU of 1800 bytes: Switch(config)# interface GigabitEthernet 1/1 Switch(config-if)# mtu 1800 Related Commands Command Description system mtu Sets the maximum Layer 2 or Layer 3 payload size. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-511...
Page 552
The default group ip address count is 0. The default query response time is 5 tenths (one-half) second. The default multicast VLAN for MVR is VLAN 1. Command Modes Global configuration Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-512...
Page 553
Use the show mvr members privileged EXEC command to display the configured IP multicast group addresses. The following example shows how to set the maximum query response time as 1 second (10 tenths): Switch(config)# mvr querytime 10 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-513...
Page 554
MVR groups of which the interface is a member. show mvr members Displays all ports that are members of an MVR multicast group; if the group has no members, its status is shown as Inactive. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-514...
Page 555
No receiver port belongs to any configured multicast group. Command Modes Interface configuration Command History Release Modification Release IOS XE 3.5.0E This command was introduced on the Catalyst 4500 series switch. and IOS 15.2(1)E Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-515...
Page 557
Also displays all MVR groups of which the interface is a member. show mvr members Displays all receiver ports that are members of an MVR multicast group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-517...
Page 558
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines Two or more Catalyst 4500 series switches with the same VLAN mapping and configuration version number are considered to be in different MST regions if the region names are different.
Page 559
Switch(config-netflow-lite-exporter)# transport udp 8188 Switch(config-netflow-lite-exporter)# ttl 128 Switch(config-netflow-lite-exporter)# cos 7 Switch(config-netflow-lite-exporter)# dscp 32 Switch(config-netflow-lite-exporter)# template data timeout 1 Switch(config-netflow-lite-exporter)# options sampler-table timeout 1 Switch(config-netflow-lite-exporter)# options interface-table timeout 1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-519...
Page 560
Specifies a template data timeout for the NetFlow-lite collector. (netflow-lite exporter submode) options timeout (netflow-lite Specifies an options timeout for the NetFlow-lite collector. exporter submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-520...
Page 561
If the physical port is a member of a port channel, applying the monitor to the port has no effect. You must apply the monitor to the port channel instead. VLAN sampling is not supported in Cisco IOS Release 15.0(2)SG. It will be supported in a later release. Note Mandatory parameters are sampler and exporter.
Page 562
Activate sampling on an interface in netflow-lite monitor submode) submode. average-packet-size Specifies the average packet size at the observation point. (netflow-lite monitor submode) exporter (netflow-lite monitor Assigns an exporter in netflow-lite monitor submode. submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-522...
Page 564
(netflow-lite Specifies a packet sampling rate in netflow-lite sampler submode. sampler submode) packet-section size (netflow-lite Specifies a sampled header size in netflow-lite submode. sampler submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-524...
Page 565
Command Description clear nmsp statistics Clears the NMSP statistic counters. nmsp attachment suppress Suppress reporting attachment information from a specified interface. show nmsp Displays the NMSP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-525...
Page 566
Switch(config)# switch interface gigabitethernet1/2 Switch(config-if)# nmsp attachment suppress Switch(config-if)# Related Commands Command Description nmsp Configures Network Mobility Services Protocol (NMSP) on the switch. show nmsp Displays the NMSP information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-526...
Page 567
Object groups for ACLs is supported only on Catalyst 4500-X Series Switches, and Catalyst 4500-E Note Series Switches (with Supervisor Engines 7-E, 7L-E, and 8-E). object-group {network | service} object-group-name no object-group {network | service} object-group-name Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-527...
Page 568
The object group name is a sequence of 1 to 64 characters consisting of letters, digits, underscores (_), dashes (-), or periods (.). The object-group-name must start with a letter. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-528...
Page 569
For example, Switch(config)#ip access-list extend acl-1 Switch(config-ext-nacl)#permit ip object-group OG-1 any OG-1 doesn’t exist, this line is rejected. Specifics for network groups http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/security/m1/sec-m1-cr-book/sec-cr-m2.html#wp275 4379810 Specifics for service groups Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-529...
Page 571
(netflow-lite exporter submode) export-protocol (netflow-lite Specifies the export protocol for the NetFlow-lite collector. exporter submode) dscp (netflow-lite exporter Specifies a cos value for the NetFlow-lite collector. submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-531...
Page 572
Packet Sampling rate: 1 out of 32 Packet Section Size: bytes Packet offset: bytes You can verify your settings with the show netflow-lite sampler privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-532...
Page 573
Description packet-section size (netflow-lite Specifies a sampled header size in netflow-lite submode. sampler submode) packet-rate (netflow-lite Specifies a packet sampling rate in netflow-lite sampler submode sampler submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-533...
Page 574
Switch(config)# exit Switch# Switch# show netflow-lite sampler sampler1 Netflow-lite Sampler sampler1: Id : Packet Sampling rate: 1 out of 32 Packet Section Size: bytes Packet offset: bytes Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-534...
Page 575
Command Description packet-section size (netflow-lite Specifies a sampled header size in netflow-lite submode. sampler submode) packet-offset (netflow-lite Specifies a starting packet offset in netflow-lite submode. sampler submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-535...
Page 576
Packet Sampling rate: 1 out of 32 Packet Section Size: bytes Packet offset: bytes You can verify your settings with the show netflow-lite sampler privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-536...
Page 577
Command Description packet-rate (netflow-lite Specifies a packet sampling rate in netflow-lite sampler submode. sampler submode) packet-offset (netflow-lite Specifies a starting packet offset in netflow-lite submode. sampler submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-537...
Page 578
The following example shows how to enable aggregation port address learning within the bundle: Switch(config-if)# pagp learn-method aggregation-port Switch(config-if)# Related Commands Command Description show pagp Displays information about the port channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-538...
Page 579
Switch(config-if)# pagp port-priority 45 Switch(config-if)# Related Commands Command Description pagp learn-method Learns the input interface of the incoming packets. show pagp Displays information about the port channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-539...
Page 580
You can either specify the interfaces or the name of an interface-range macro. An interface range must consist of the same interface type, and the interfaces within a range cannot span across the modules. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-540...
Page 581
The following example sends EIGRP updates to all interfaces on network 10.108.0.0 except GigabitEthernet interface 1/1: Switch(config)# interface gigabitethernet 1/1 Switch(config-if)# router eigrp 109 Switch(config-router)# network 10.108.0.0 Switch(config-router)# passive-interface gigabitethernet 1/1 Switch(config-router)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-541...
Page 582
The following configuration sets the Ethernet ports 3 through 4 on module 0 and GigabitEthernet ports 4 through 7 on module 1 as passive: Switch(config-if)# router ospf 100 Switch(config-router)# passive-interface range ethernet0/3-4,gigabitethernet1/4-7 Switch(config-router)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-542...
Page 583
(Optional) Logs a packet when it matches the access control entry (ACE). Command Default This command has no default settings. Command Modes arp-nacl configuration mode Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-543...
Page 584
Permits ARPs from hosts that are configured for static IP when DAI is enabled and to define an ARP access list and applies it to a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-544...
Page 585
Policy-map class configuration mode (when specifying a single action to be applied to a market packet) Policy-map class police configuration mode (when specifying multiple actions to be applied to a marked packet) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-545...
Page 586
The conform bucket is initially full (the full size is the number of bytes specified as the normal burst size). The exceed bucket is initially full (the full exceed bucket size is the number of bytes specified in the maximum burst size). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-546...
Page 587
800 bytes in the token bucket. If the next packet is 900 bytes, the packet exceeds and the exceed action (drop) is taken. No bytes are taken from the token bucket. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-547...
Page 588
200 bytes are available in the conform bucket. Similarly, the packet does not exceed because only 300 bytes are available in the exceed bucket. Therefore, the packet violates and the violate action (drop) is taken. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-548...
Page 589
Displays information about the policy map. show policy-map interface Displays the statistics and configurations of the input and output policies that are attached to an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-549...
Page 590
IP precedence and transmits the • packet with the new IP precedence value setting. transmit—Transmits the packet. The packet is not altered. • Command Default This command is disabled by default. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-550...
Page 591
Switch(config-pmap)# class-map class1 Switch(config-pmap-c)# police cir percent 20 bc 3 ms pir percent 40 be 4 ms Switch(config-pmap-c)# exit Switch(config-pmap-c)# interface gigabitethernet 6/2 Switch(config-if)# service-policy output policy Switch(config-if)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-551...
Page 592
(Optional) Peak burst rate, in milliseconds, will be used for policing traffic. Valid range is a number from 1 to 2,000. Command Default This command is disabled by default. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-552...
Page 593
Command History Release Modification 12.2(40)SG This command was introduced on the Catalyst 4500 series switch using a Supervisor Engine 6-E. Usage Guidelines Use the police rate command to limit traffic on the basis of pps, bps, or a percentage of interface bandwidth.
Page 594
IP precedence value setting. transmit—Sends the packet with no alteration. • Command Default This command is disabled by default. Command Modes Policy-map configuration mode Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-554...
Page 595
Command History Release Modification 12.2(40)SG This command was introduced on the Catalyst 4500 series switch using a Supervisor Engine 6-E. Usage Guidelines Refer to RFC 2698-Two Rate Three Color Marker. Two-rate traffic policing uses two token buckets—Tc and Tp—for policing traffic at two independent rates.
Page 596
500 kbps, but not exceeding 1 Mbps, will be marked with IP Precedence 2 and then sent. All traffic marked as exceeding 1 Mbps will be dropped. The burst parameters are set to 10000 bytes. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-556...
Page 597
IP Precedence 2 and then sent. Packets marked as violating the rate are dropped. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-557...
Page 598
Examples The following example shows how to configure multiple classes in a policy map called policymap2 on a Supervisor Engine 6-E: Switch# configure terminal Switch(config)# policy-map policymap2 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-558...
Page 599
Attaches a policy map to an interface or applies different QoS configuration) policies on VLANs that an interface belongs to. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-559...
Page 600
Switch(config)# port-channel load-balance dst-ip Switch(config)# The following example shows how to set the load-distribution method to the source XOR destination IP address: Switch(config)# port-channel load-balance src-dst-port Switch(config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-560...
Page 601
Chapter 2 port-channel load-balance Related Commands Command Description interface port-channel Accesses or creates a port-channel interface. show etherchannel Displays EtherChannel information for a channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-561...
Page 602
The following example shows how to enable the EtherChannel standalone option in a port channel: Switch(config-if)# no port-channel standalone-disable Related Commands Command Description show etherchannel Displays EtherChannel information for a channel. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-562...
Page 603
Configures a sticky address on an interface for a specific VLAN sticky or VLAN range. port-security maximum Configures the maximum number of addresses on an interface for a specific VLAN or VLAN range. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-563...
Page 604
Configures a secure address on an interface for a specific VLAN or VLAN range. port-security maximum Configures the maximum number of addresses on an interface for a specific VLAN or VLAN range. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-564...
Page 605
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface g1/1 Switch(config-if)# switchport trunk encapsulation dot1q Switch(config-if)# switchport mode trunk Switch(config-if)# vlan 2-3 Switch(config-if-vlan-range)# port-security maximum 5 Switch(config-if-vlan-range)# exit Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-565...
Page 606
Configures a secure address on an interface for a specific VLAN or VLAN range. port-security mac-address Configures a sticky address on an interface for a specific VLAN sticky or VLAN range. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-566...
The following example shows how to set the total capacity of the external DC power source to 5000 W: Switch(config)# power dc input 5000 Switch(config)# Related Commands Command Description show power Displays information about the power status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-567...
Page 608
PHY's operating circuitry and save power. This functionality is provided per port and is not enabled by default. To avoid issues with EEE functionality on any port during run-time, Cisco provides the power efficient-ethernet auto command to enable or disable EEE.
WS-X4648-RJ45V+E. Usage Guidelines If your interface is not capable of supporting Power over Ethernet, you will receive this message: Power over Ethernet not supported on interface Admin Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-569...
Page 610
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface gigabitethernet 2/1 Switch(config-if)# power inline static max 16500 Switch(config-if)# end Switch# Related Commands Command Description show power Displays information about the power status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-570...
Support added for Power over Ethernet. Usage Guidelines The inline power consumption command overrides the power allocated to the port through IEEE/Cisco phone discovery and CDP/LLDP power negotiation. To guarantee safe operation of the system, ensure that the value configured here is no less than the actual power requirement of the attached device. If the power drawn by the inline powered devices exceeds the capability of the power supply, it could trip the power supply.
Page 612
Switch(config)# power inline consumption default 8000 Switch(config)# end Switch# Related Commands Command Description power inline Sets the inline-power state for the inline-power-capable interfaces. show power Displays information about the power status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-572...
Page 613
Command History Release Modification 15.0(2)SG This command was introduced on the Catalyst 4500 series switch using a Supervisor Engine 7-E and 7L-E. Usage Guidelines Although IEEE 802.at only provides for power up to 30W per port, the WS-X4748-UPOE+E module can provide up to 60W using the spare pair of an RJ45 cable (wires 4,5,7,8) with the signal pair (wires 1,2,3,6).
Page 614
Do not enter this command if the end-device is incapable of sourcing inline power on the spare pair or if the end-device supports the CDP or LLDP extensions for UPOE. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-574...
Page 615
*Oct 17 12:02:54.915: %ILPOWER-7-DETECT: Interface Gi5/5: Power Device detected: IEEE PD Related Commands Command Description logging event link-status global (global Changes the default switch-wide global link-status event configuration) messaging settings. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-575...
Page 616
State State Police Police Power Power --------- ------ ---------- ---------- ---------- ------ ----- Gi2/1 auto errdisable ok 17.4 Switch(config-if)# power inline police action log Available:421(w) Used:39(w) Remaining:382(w) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-576...
Page 617
Displays the PoE policing status of an interface, module, or chassis. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-577...
Page 618
7600 W and one subunit fails or is powered off, you have three quality inputs providing 5500 W and the chassis is powered at the same rate as it was prior to the failure event: Switch# configuration terminal Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-578...
Page 619
---- --------- System Power (12V) 2400 Inline Power (-50V) 2000 Backplane Power (3.3V) ---------------------- ---- --------- Total 140 (not to exceed Total Maximum Available = 2728) Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-579...
Page 620
The maximum inputs part of the command is ignored by all power supplies other than the 4200 W AC Note or 6000 W AC. Switch# configure terminal Switch(config)# power redundancy combined max inputs {2 | 3} Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-580...
Page 621
Chapter 2 power redundancy combined max inputs Related Commands Command Description show power Displays information about the power status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-581...
Page 622
In redundant mode, the power from a single power supply must provide enough power to support the switch configuration. Table 2-12 lists the maximum available power for chassis and Power over Ethernet for each power supply. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-582...
Page 623
(the type of line cards, the number of line cards, number of ports consuming inline power, etc.) and does not reflect the absolute maximum power. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-583...
Page 624
Combined Mode Output for the 6000 W AC Power Supply Power Supply Chassis Power Inline Power Both sides (bays) at 110 V 1400 1670 110 V+110 V, other side 110 V 2360 2560 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-584...
Page 625
Both sides at 220VAC 2828 4150 4930 Both sides at 220VAC + 220VAC 3762 8300 10140 Both sides at 220VAC + 220VAC + 3762 14400 17210 220VAC Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-585...
Page 626
The following example shows how to set the power management mode to combined: Switch(config)# power redundancy-mode combined Switch(config)# Related Commands Command Description show power Displays information about the power status. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-586...
Page 627
The following example shows how to disable PPPoE Intermediate Agent on a switch: Switch(config)# no pppoe intermediate-agent Related Commands Command Description pppoe intermediate-agent Sets the access node identifier, generic error message, and (global) identifier string for a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-587...
Page 628
Sets the trust configuration of an interface. trust pppoe intermediate-agent Enables vendor-tag stripping on PPPoE Discovery packets from vendor-tag strip PPPoE Server (or BRAS). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-588...
Page 629
The following example shows how to disable PPPoE Intermediate Agent on a single VLAN: Switch(config-if)# vlan-range 268 Switch(config-if-vlan-range)# no pppoe intermediate-agent Related Commands Command Description pppoe intermediate-agent Enables the PPPoE Intermediate Agent feature on an interface. (interface) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-589...
Page 630
Use the access-node-identifier and identifier-string commands to enable the switch to generate the circuit-id parameters automatically. The no form of identifier-string command unsets the option and delimiter. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-590...
Page 631
The following example shows how to unset a generic-error-message: Switch(config)# no pppoe intermediate-agent format-type generic-error-message Related Commands Command Description show pppoe Displays the PPPoE Intermediate Agent configuration and intermediate-agent interface statistics (packet counters). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-591...
Page 632
Command Description pppoe intermediate-agent Enables the PPPoE Intermediate Agent feature on an interface. (interface) pppoe intermediate-agent Sets the circuit-id or remote-id for an interface vlan-range. (interface vlan-range) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-592...
Page 633
The following example shows how to unset circuit-id on an interface vlan-range: Switch(config-if)# vlan-range 167-368 Switch(config-if-vlan-range)# no pppoe intermediate-agent format-type circuit-id Related Commands Command Description pppoe intermediate-agent Enables PPPoE Intermediate Agent on an interface VLAN range. (interface vlan-range) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-593...
Page 634
The following example shows how to disable rate limiting for an interface: Switch(config-if)# no pppoe intermediate-agent limit rate Related Commands Command Description pppoe intermediate-agent Enables the PPPoE Intermediate Agent feature on an interface (interface) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-594...
Page 635
The following example shows how to disable the trust configuration for an interface: Switch(config-if)# no pppoe intermediate-agent trust Related Commands Command Description pppoe intermediate-agent Enables vendor-tag stripping on PPPoE Discovery packets from a vendor-tag strip PPPoE Server (or BRAS). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-595...
Page 636
Switch(config-if)# no pppoe intermediate-agent vendor-tag strip Related Commands Command Description pppoe intermediate-agent Enables the PPPoE Intermediate Agent feature on an interface. (interface) pppoe intermediate-agent Sets the trust configuration of an interface. trust Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-596...
Page 637
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# policy-map policy1 Switch(config-pmap)# class voice Switch(config-pmap-c)# priority You can verify your settings by entering the show policy-map privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-597...
Page 638
(class-based queueing) Enables traffic shaping a class of traffic in a policy map attached to a physical port. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-598...
Page 639
You cannot configure VLAN 1 or VLANs 1001 to 1005 as private VLANs. VTP does not support private VLANs. You must configure private VLANs on each device where you want private VLAN ports. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-599...
Page 640
The private-vlan commands do not take effect until you exit the config-VLAN submode. If you delete either the primary or secondary VLAN, the ports that are associated with the VLAN become inactive. Refer to the Catalyst 4500 Series Switch Cisco IOS Software Configuration Guide for additional configuration guidelines. Examples...
Page 641
Switch(config)# vlan 202 Switch(config-vlan)# private-vlan association 303-307,309,440 Switch(config-vlan)# end Switch# show vlan private-vlan Primary Secondary Type Interfaces ------- --------- ----------------- ------------------------------------------ community community community community community community Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-601...
Page 642
Pruning VLANs Enabled: 2-1001 Capture Mode Disabled Capture VLANs Allowed: ALL Related Commands Command Description show vlan Displays VLAN information. show vlan private-vlan Displays private VLAN information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-602...
Page 643
VLAN), all the SVIs that are specified in this command are brought down. If you configure a mapping between two VLANs that do not have a valid Layer 2 association, the mapping configuration does not take effect. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-603...
Page 644
Switch# show interfaces private-vlan mapping Interface Secondary VLAN Type --------- -------------- ----------------- vlan202 community vlan202 community vlan202 community vlan202 community vlan202 community vlan202 community vlan202 isolated Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-604...
Page 645
Related Commands Command Description show interfaces private-vlan Displays PVLAN mapping information for VLAN SVIs. mapping show vlan Displays VLAN information. show vlan private-vlan Displays private VLAN information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-605...
Page 646
Switch(config-mst)# exit These secondary vlans are not mapped to the same instance as their primary: ->3 Switch(config)# Related Commands Command Description show spanning-tree mst Displays MST protocol information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-606...
Page 648
Subscribes this destination profile to the Environment alert group. subscribe-to-alert-group inventory Subscribes this destination profile to the Inventory alert group. subscribe-to-alert-group syslog Subscribes this destination profile to the Syslog alert group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-608...
Page 649
MSP device handler is tightly coupled with MSP flow parser. Not enabling this CLI means that MSP will not send SIP, H323 notifications to IOS sensor. Examples The following example shows how to enable MSP: Switch(config)# profile flow Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-609...
Page 650
The following example shows how to shows how to include IPG in policing: Switch)# config t Switch(config)# qos account layer-all encapsulation Switch(config)# end Switch# Related Commands Command Description show policy-map interface Displays policer statistics on a specific interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-610...
The following example shows how to include an additional 18 bytes when policing IP packets: Switch# config terminal Switch(config)# qos account layer2 encapsulation length 18 Switch (config)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-611...
Page 652
Displays traffic on a specific interface. switchport Modifies the switching characteristics of a Layer 2 switch interface. switchport block Prevents the unknown multicast or unicast packets from being forwarded. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-612...
{cos | device cisco-phone | dscp | extend [cos priority]} no qos trust {cos | device cisco-phone | dscp | extend [cos priority]} Syntax Description Specifies that the CoS bits in incoming frames are trusted and derives the internal DSCP value from the CoS bits.
Page 654
The following example shows how to set the PVID CoS level to 6: Switch(config-if)# qos trust extend cos 6 Switch(config-if)# The following example shows how to set the Cisco phone as the trust device: Switch(config-if)# qos trust device cisco-phone Switch(config-if)#...
Page 655
The queue-limit command is supported only after you first configure a scheduling action, such as Note bandwidth, or priority, except when you configure queue-limit in the class-default class of an output QoS policy-map.s Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-615...
Page 656
(class-based queueing) Enables traffic shaping a class of traffic in a policy map attached to a physical port. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-616...
Page 657
Command History Release Modification 12.1(12c)EW This command was introduced on the Catalyst 4500 series switch (Catalyst 4507R and 4510R only). Usage Guidelines The redundancy configuration mode is used to enter the main CPU submode. To enter the main CPU submode, use the main-cpu command in the redundancy configuration mode.
Page 658
Description auto-sync Enables automatic synchronization of the configuration files in NVRAM. main-cpu Enters the main CPU submode and manually synchronize the configurations on the two supervisor engines. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-618...
Page 659
If your active and standby supervisors engines are running different versions of Cisco IOS, some of their CLIs will not be compatible. If such commands are already present in the running configuration of the...
Page 660
The following example shows how to validate removal of entries from the MCL: Switch# redundancy config-sync validate mismatched-commands Switch# Related Commands Command Description show redundancy config-sync Displays an ISSU config-sync failure or the ignored mismatched command list (MCL). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-620...
Page 661
The following example shows how to switch over manually from the active to the standby supervisor engine: Switch# redundancy force-switchover Switch# Related Commands Command Description redundancy Enters the redundancy configuration mode. show redundancy Displays redundancy facility information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-621...
The following example shows how to manually reload one or both supervisor engines: Switch# redundancy reload shelf Switch# Related Commands Command Description redundancy Enters the redundancy configuration mode. show redundancy Displays redundancy facility information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-622...
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines This command applies only to the Access Gateway Module on Catalyst 4500 series switches. The valid values for mod depends on the chassis used. For example, if you have a Catalyst 4506 chassis, valid values for the module are from 2 to 6.
Page 664
The following example shows how to convert a VLAN into an RSPAN VLAN: Switch# config terminal Switch(config)# vlan 20 Switch(config-vlan)# remote-span Switch(config-vlan)# end Switch# Related Commands Command Description monitor session Enables the SPAN sessions on interfaces or VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-624...
Enables DHCP snooping on a VLAN or a group of VLANs. show ip dhcp snooping Displays the DHCP snooping configuration. show ip dhcp snooping binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-625...
The administrative VLAN cannot be the RSPAN VLAN. Examples The following example shows how to configure VLAN 100 as the REP administrative VLAN: Switch(config)# rep admin vlan 100 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-626...
Page 667
You can verify your settings by entering the show interface rep detail privileged EXEC command. Related Commands Command Description show interfaces rep Displays detailed REP configuration and status for all interfaces or the detail specified interface, including the administrative VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-627...
VLAN load balancing. Command Modes Interface configuration Command History Release Modification 12.2(44)SG This command was introduced. Usage Guidelines You must enter this command on the REP primary edge port. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-628...
Page 669
VLAN list on one port and then use the same command to block another VLAN list on another port, the original port number and VLAN list are overwritten. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-629...
Page 671
Manually starts REP VLAN load balancing on a segment. show interfaces rep Displays REP detailed configuration and status for all interfaces or the detail specified interface, including the administrative VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-631...
Page 672
In Cisco IOS Release 12.2(52)SE, the LSL age-timer range changed from 3000 to 10000 ms in 500-ms increments to 120 to 10000 ms in 40-ms increments. If the REP neighbor device is not running Cisco IOS Release 12.2(52)SE or later, you must use the shorter time range because the device does not accept values out of the earlier range.
Page 673
Related Commands Command Description show interfaces rep Displays REP configuration and status for all interfaces or the specified [detail] interface, including the configured LSL age-out timer value. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-633...
Switch(config)# interface gigabitethernet1/0/1 Switch(config-if)# rep preempt delay 100 Switch(config-if)# exit You can verify your settings by entering the show interfaces rep privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-634...
Page 675
Related Commands Command Description rep block port Configures VLAN load balancing. show interfaces rep [detail] Displays REP configuration and status for all interfaces or the specified interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-635...
Related Commands Command Description rep block port Configures VLAN load balancing. show interfaces rep [detail] Displays REP configuration and status for all interfaces or the specified interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-636...
REP ports must be Layer 2 trunk ports. A non-ES REP port can be either an IEEE 802.1Q trunk port or an ISL trunk port. REP ports should not be configured as one of these port types: SPAN destination port • • Private VLAN port Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-637...
Page 678
The following example shows how to configure the same configuration when the interface has no external REP neighbor: Switch# configure terminal Switch (config)# interface gigabitethernet1/1 Switch (config-if)# rep segment 100 edge no-neighbor primary Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-638...
Page 679
Displays REP configuration and status for all interfaces or the specified [detail] interface. show rep topology Displays information about all ports in the segment, including which one was [detail] configured and selected as the primary edge port. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-639...
Switch (config)# interface GigabitEthernet1/1 Switch (config-if)# rep stcn segment 25-50 Switch (config-if)# exit You can verify your settings by entering the show interfaces rep detail privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-640...
Page 681
Chapter 2 rep stcn Related Commands Command Description show interfaces rep Displays REP configuration and status for all interfaces or the specified [detail] interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-641...
Page 682
This command was introduced on the Catalyst 4500 series switch. Examples The following example shows how to reset the proposed new VLAN database to the current VLAN database: Switch(vlan-config)# reset RESET completed. Switch(vlan-config)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-642...
Page 683
12.1(12c)EW This command was introduced on the Catalyst 4500 series switch. Usage Guidelines If two Catalyst 4500 series switches have the same configuration but have different configuration revision numbers, they are considered to be part of two different regions. Caution Be careful when using the revision command to set the MST configuration revision number because a mistake can put the switch in a different region.
Page 685
Related Commands Command Description average-packet-size Specifies the average packet size at the observation point. (netflow-lite monitor submode) exporter (netflow-lite monitor Assigns an exporter in netflow-lite monitor submode. submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-645...
Page 686
The following example shows how to attach a policy map to Fast Ethernet interface 5/20: Switch# configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# interface fastethernet 5/20 Switch(config-if)# service-policy input pmap1 Switch(config-if)# end Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-646...
Page 688
(interface Attaches a policy map to an interface. configuration) show policy-map interface Displays the QoS policy-map information applied to a specific vlan VLAN on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-648...
Page 689
Switch(config-pmap)# exit Switch(config)# policy-map parent Switch(config-pmap)# class class1 Switch(config-pmap-c)# police 32k Switch(config-pmap-c)# service-policy child Switch# You can verify your settings by entering the show policy-map privileged EXEC command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-649...
Page 690
(class-based queueing) Enables traffic shaping a class of traffic in a policy map attached to a physical port. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-650...
Switch(config)# policy-map control-plane-policy Switch(config-pmap)# class telnet-class Switch(config-pmap-c)# police 80000 conform transmit exceed drop Switch(config-pmap-c)# exit Switch(config-pmap)# exit ! Define aggregate control plane service for the active Route Processor. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-651...
Page 692
Displays the configuration either of a class or of all classes for the control-plane policy map of a control plane. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-652...
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines Catalyst 4500 series switches can be configured with two supervisor engines to provide redundancy. When the switch is powered, one of the supervisor engines becomes active and remains active until a switchover occurs.
Page 694
Standby console disabled. Valid commands are: exit, logout Related Commands Command Description attach module Remotely connects to a specific module. remote login module Remotely connects to a specific module. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-654...
Page 695
VLAN. To return to policy-map configuration mode, use the exit command. To return to privileged EXEC mode, use the end command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-655...
Page 696
Displays information about the policy map. trust Defines a trust state for traffic classified through the class policy-map configuration command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-656...
Page 697
CoS value. The “from-field” packet-marking categories are as follows: • Precedence • Differentiated services code point (DSCP) Cost of Service (CoS) • Quality of Service (QoS) group • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-657...
Page 698
(policy-map Creates a service policy that is a quality of service (QoS) policy class) within a policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-658...
Page 699
(DSCP) value in the type of service (ToS) byte. set precedence Sets the precedence value in the packet header. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-659...
Command History Release Modification 12.2(8a)EW This command was introduced on the Catalyst 4500 series switch. 12.2(40)SG Added support for from-field on Supervisor Engine 6-E and Catalyst 4900M. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-660...
Page 701
The table map was created earlier with the table-map (value mapping) command. For more information about the table-map (value mapping) command, see the table-map (value mapping) command page. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-661...
Page 702
(value mapping) Modifies metric and tag values when the IP routing table is (refer to Cisco IOS updated with BGP learned routes. documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-662...
The set precedence command cannot be used with the set dscp command to mark the same packet. The two values, DSCP and precedence, are mutually exclusive. A packet can be one value or the other, but not both. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-663...
Page 704
The following example shows how the precedence value is set according to the CoS value defined in table-map1. Switch# configure terminal Switch(config)# policy-map policy-cos Switch(config-pmap)# class class-default Switch(config-pmap-c)# set precedence cos table table-map1 Switch(config-pmap-c)# end Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-664...
(value mapping) Modifies metric and tag values when the IP routing table is (refer to Cisco IOS updated with BGP learned routes. documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-665...
Release Modification 12.2(40)SG This command was introduced on the Catalyst 4500 series switch using a Supervisor Engine 6-E and Catalyst 4900M chassis. Usage Guidelines The set qos-group command allows you to associate a group ID with a packet. This association is made through a service-policy attached to an interface or VLAN in the input direction.
Page 707
Displays information about the policy map. show policy-map interface Displays the statistics and configurations of the input and output policies that are attached to an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-667...
Page 708
However, you can use these commands in the same policy map. To return to policy-map configuration mode, use the exit command. To return to privileged EXEC mode, use the end command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-668...
Page 709
(policy-map Creates a service policy that is a quality of service (QoS) policy class) within a policy map. show policy-map Displays information about the policy map. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-669...
Page 710
The two 1000BASE-X ports on the WS-X4232-GB-RJ module • The first two ports on the WS-X4418-GB module • The two 1000BASE-X ports on the WS-X4412-2GB-TX module • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-670...
Page 711
Examples The following example shows how to configure a maximum bandwidth (70 percent) for the interface fa3/1: Switch(config)# interface fastethernet3/1 Switch(config-if)# tx-queue 3 Switch(config-if-tx-queue)# shape 70m Switch(config-if-tx-queue)# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-671...
Page 712
IDs to their respective macros or functions. Examples The following example shows how to create a user-defined event trigger called RADIUS_MAB_EVENT: Switch# configure terminal Switch(config)# shell trigger RADIUS_MAB_EVENT MAC_AuthBypass Event Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-672...
Page 713
Enables Auto SmartPorts macros on a specific interface. macro auto sticky Specifies not to remove configurations applied by ASP across link flaps and device removal. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-673...
Page 714
Chapter 2 shell trigger Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-674...
Page 715
Access group mode is: merge Switch# Related Commands Command Description access-group mode Specifies the override modes (for example, VACL overrides PACL) and the non-override modes (for example, merge or strict mode). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-667...
The following information is contained in the show adjacency command: Protocol interface. • Type of routing protocol that is configured on the interface. • Interface address. • Method of adjacency that was learned. • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-668 OL-30934-01...
Page 717
The following example shows how to display adjacency information for a specific interface: Switch# show adjacency fastethernet2/3 Protocol Interface Address FastEthernet2/3 172.20.52.1(3045) FastEthernet2/3 172.20.52.22(11) Switch# Related Commands Command Description debug adjacency Displays information about the adjacency debugging. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-669...
Page 718
0x0106000400140703 20 Fa7/3 18:27:35 UTC Sat Sep 13 2008 0x01060004000A0704 10 Fa7/4 18:25:43 UTC Sat Sep 13 2008 0x0106000400140704 20 Fa7/4 18:25:43 UTC Sat Sep 13 2008 ANCP-Client# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-670 OL-30934-01...
Page 719
Permits ARPs from hosts that are configured for static IP when DAI is enabled, defines an ARP access list, and applies the access list to a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-671...
Command Modes EXEC Command History Release Modification 12.2(50)SG This command was introduced. Usage Guidelines Table 2-19 describes the significant fields shown in the show authentication display. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-672 OL-30934-01...
Page 721
The following example shows how to display Auth Manager details for a specific interface: Switch# show authentication interface gigabitethernet1/23 Client list: MAC Address Domain Status Handle Interface 000e.84af.59bd DATA Authz Success 0xE0000000 GigabitEthernet1/0/23 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-673...
Page 722
No Auth Manager contexts match supplied criteria Switch# show authentication sessions method dot1x MAC Address Domain Status Handle Interface 000e.84af.59bd DATA Authz Success 0xE0000000 GigabitEthernet1/23 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-674 OL-30934-01...
Page 723
Enables the Webauth fallback and specifies the fallback profile to use when failing over to Webauth. authentication host-mode Defines the classification of a session that will be used to apply the access-policies using the host-mode configuration. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-675...
Page 724
Specifies the priority of authentication methods on an interface. authentication timer Configures the authentication timer. authentication violation Specifies the action to be taken when a security violation exists on a port. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-676 OL-30934-01...
Page 725
The first IP address in the display indicates the server that is used for the automatic installation. The second IP address indicates the TFTP server that provided the configuration file. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-677...
Switch# Related Commands Command Description auto qos voip Automatically configures quality of service (auto-QoS) for Voice over IP (VoIP) within a QoS domain. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-678 OL-30934-01...
Page 727
Enter configuration commands, one per line. End with CNTL/Z. Switch(config)# int g1/0/18 Switch(config-if)# auto security-port host Switch(config-if)# end Switch# 5 22:16:41.725: %SYS-5-CONFIG_I: Configured from console by consolesh auto security Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-679...
Page 728
Auto Secure CLIs applied on Trunk Port: -------------------------------------- ip dhcp snooping trust ip arp inspection trust switchport port-security maximum 100 switchport port-security violation restrict switchport port-security Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-680 OL-30934-01...
The following example shows how to display BOOT environment variable information: Switch# show bootvar BOOT variable = sup:1; CONFIG_FILE variable does not exist BOOTLDR variable does not exist Configuration register is 0x0 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-683...
Page 732
Release Modification 12.2(25)SG This command was introduced on the Catalyst 4500 series switch. Usage Guidelines The TDR test is supported on Catalyst 4500 series switches running Cisco IOS Release 12.2(25)SG for the following line cards only: WS-X4548-GB-RJ45 • WS-X4548-GB-RJ45V •...
Page 733
Terminated—The link is up. • Fault—Cable fault (open or short) • Related Commands Command Description test cable-diagnostics tdr Tests the condition of copper cables on 48-port 10/100/1000 BASE-T modules. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-685...
Page 734
1234 Picaboo Street, Any city, Any state, 12345 customer ID: ExampleCorp contract ID: X123456789 site ID: SantaClara Mail-server[1]: Address: smtp.example.com Priority: 1 Mail-server[2]: Address: 192.168.0.1 Priority: 2 Rate-limit: 20 message(s) per minute Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-686 OL-30934-01...
Page 735
Email address(es): noc@example.com HTTP address(es): Not yet set up Alert-group Severity ------------------------ ------------ inventory normal Syslog-Pattern Severity ------------------------ ------------ Profile Name: CiscoTAC-1 Profile status: ACTIVE Preferred Message Format: xml Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-687...
Page 736
Message Size Limit: 3145728 Bytes Transport Method: email Email address(es): noc@example.com HTTP address(es): Not yet set up Alert-group Severity ------------------------ ------------ inventory normal Syslog-Pattern Severity ------------------------ ------------ Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-688 OL-30934-01...
Page 737
Call Home Statistics Switch# show call-home statistics Message Types Total Email HTTP ------------- -------------------- -------------------- ------------------ Total Success Config Diagnostic Environment 0 Inventory SysLog Test Request Send-CLI Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-689...
Page 738
(global configuration) Enters call-home configuration mode. call-home send alert-group Sends a specific alert group message. service call-home (refer to Cisco IOS Enables or disables call home. documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-690 OL-30934-01...
Extended to include the 10-Gigabit Ethernet interface. Usage Guidelines The vlan keyword is supported in Catalyst 4500 series switches that are configured with a Supervisor Engine 2. The port-channel values are from 0 to 282; values from 257 to 282 are supported on the CSM and the FWSM only.
Page 740
IOS (tm) 5800 Software (C5800-P4-M), Version 12.1(2) Copyright (c) 1986-2002 by Cisco Systems, Inc. advertisement version: 2 Duplex: half ------------------------- Device ID: lab-as5300-1 Entry address(es): IP address: 172.19.169.87 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-692 OL-30934-01...
Page 741
Displays information about the interfaces on which Cisco Cisco IOS documentation) Discovery Protocol (CDP) is enabled. show cdp traffic (refer to Cisco Displays traffic information from the CDP table. IOS documentation) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-693...
Page 742
If you use the match flow ip source-address|destination-address command, these two flows are consolidated into one flow and they have the same source and destination address. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-694 OL-30934-01...
Page 743
Displays information about the policy map. show policy-map interface Displays the statistics and configurations of the input and output policies that are attached to an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-695...
Page 744
32 3D 1E 00 63 69 73 63 6F 2D 30 30 32 34 2E 31 34 64 63 2E 64 66 34 64 2D 47 69 31 2F 30 2F 32 34 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-696...
Page 745
Creates a DHCP filter containing a list of options that can be included or dhcp excluded in the Device Sensor output. show device-sensor Displays Device Sensor cache entries. cache Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-697...
Page 746
Test Name Attributes (day hh:mm:ss.ms) ==== ========================================== ============ ================= 1) supervisor-bootup -----------------------> **D****I** not configured 2) packet-memory-bootup --------------------> **D****I** not configured 3) packet-memory-ongoing -------------------> **N****I*o not configured Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-698 OL-30934-01...
Page 747
Displays the results of the bootup packet memory test. test 2 show diagnostic result module Displays the results from the ongoing packet memory test. test 3 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-699...
Page 750
Total failure count -----------------> 0 Consecutive failure count -----------> 0 packet buffers on free list: 64557 bad: 0 used for ongoing tests: 979 Packet memory errors: 0 0 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-702 OL-30934-01...
Page 751
Ignored on high gigaport: 0 Ongoing diag action mode: Normal Last 1000 Memory Test Failures: Last 1000 Packet Memory errors: First 1000 Packet Memory errors: ___________________________________________________________________________ Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-703...
Page 752
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines The detail keyword is intended for use by Cisco support personnel when analyzing failures. Examples The following example shows how to display the results of the bootup packet memory tests:...
Page 753
Consecutive failure count -----------> 0 Detailed Status --------------- TDR test is in progress on interface Gi6/1 ___________________________________________________________________________ Switch# Related Commands Command Description diagnostic start Runs the specified diagnostic test. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-705...
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines The detail keyword is intended for use by Cisco support personnel when analyzing failures. Examples The following example shows how to display the results of the bootup packet memory tests: Switch# show diagnostic result module 1 test 2 Test results: (.
Page 755
Directs the action of the switch when it detects a packet memory failure. show diagnostic result module Displays the results from the ongoing packet memory test. test 3 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-707...
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines The detail keyword is intended for use by Cisco support personnel when analyzing failures. Examples The following example shows how to display the results from the ongoing packet memory tests: Switch# show diagnostic result module 1 test 3 Test results: (.
Page 757
Directs the action of the switch when it detects a packet memory failure. show diagnostic result module Displays the results of the bootup packet memory test. test 2 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-709...
Output are displayed. The show dot1x command displays the currently assigned reauthentication timer and time remaining before reauthentication, if reauthentication is enabled. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-710 OL-30934-01...
Page 759
The remaining fields in the display show internal state information. For a detailed description of these state machines and their settings, refer to the 802.1X specification. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-711...
Page 760
Number of valid EAPOL frames of any type that have been received. RxVersion Protocol version number carried in the most recently received EAPOL frame. LastRxSrcMac Source MAC address carried in the most recently received EAPOL frame. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-712 OL-30934-01...
Page 761
EAP-Request/Identity frame to the client before restarting the authentication process. dot1x port-control Enables manual control of the authorization state on a port. mac-address-table notification Enables MAC address notification on a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-713...
PWR-C45-1400AC AC 1400W good good none Power Supply Absolute (Nos in Watts) Inline Inline System System Maximum -------------- ------ ------ ------ ------ -------- 1360 1360 1400 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-714 OL-30934-01...
Page 763
The following example shows how to display information about the fan tray: Switch# show environment status fantray Fantray : good Power consumed by Fantray : 50 Watts Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-715...
Page 764
Switch# show environment temperature Chassis Temperature = 32 degrees Celsius Chassis Over Temperature Threshold = 75 degrees Celsius Chassis Critical Temperature Threshold = 95 degrees Celsius Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-716 OL-30934-01...
Enabled port gbic-invalid Enabled port inline-power Enabled port invalid-policy Enabled port l2ptguard Enabled port link-flap Enabled port loopback Enabled port lsgroup Enabled port pagp-flap Enabled port Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-717...
Page 766
Enables error-disabled detection for a specific cause or all causes. show errdisable recovery Displays error-disabled recovery timer information. show interfaces status Displays interface status or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-718 OL-30934-01...
Disabled arp-inspection Disabled loopback Disabled Timer interval:300 seconds Interfaces that will be enabled at the next timeout: Interface Errdisable reason Time left(sec) --------- ----------------- -------------- Gi1/0/2 link-flap Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-719...
Page 768
Configures the recover mechanism variables. show errdisable detect Displays error-disabled detection status. show interfaces status Displays interface status or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-720 OL-30934-01...
= 10/1 Number of ports in agport = 0 = 0x00000000 HotStandBy port = null Passive port list = Fa5/4 Fa5/5 Port state = Port-channel L3-Ag Ag-Not-Inuse Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-721...
Page 770
S - Switching timer is running. I - Interface timer is running. Local information: Hello Partner PAgP Learning Group Port Flags State Timers Interval Count Priority Method Ifindex Fa5/5 U1/S1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-722 OL-30934-01...
Page 771
Timers: H - Hello timer is running. Q - Quit timer is running. S - Switching timer is running. I - Interface timer is running. Local information: Hello Partner PAgP Learning Group Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-723...
Page 772
(Mode ON) Switch# Related Commands Command Description channel-group Assigns and configures an EtherChannel interface to an EtherChannel group. interface port-channel Accesses or creates a port-channel interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-724 OL-30934-01...
Page 773
192.168.1.4 example-key1 192.168.1.5 example-key2 Number of "Border" node(s): 1 IP Address --------------- 192.168.1.6 Number of context(s): 2 Codes: * - Not Configured Name Host-pools ------------------------------------------------ default example-context Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-725...
Page 774
This is sample output for the show fabric context command: device#show fabric context Fabric-domain: default Number of context(s): 2 Name Host-pools ---------------------------------------------- default example-context * - Not Configured Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-726 OL-30934-01...
Page 775
Number of host-pools : 0 name vlan prefix gateway use-dhcp ----------------------------------------------------------------------------------- context: example-context Number of host-pools : 1 name vlan prefix gateway use-dhcp ----------------------------------------------------------------------------------- VOICE_DOMAIN 192.168.1.0/24 192.168.1.254 209.65.201.6 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-727...
Flow-control operation. Possible setting: disagree indicates the two ports could not agree on a link protocol. RxPause Number of pause frames received. TxPause Number of pause frames transmitted. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-728 OL-30934-01...
Page 777
Configures a Gigabit Ethernet interface to send or receive pause frames. show interfaces status Displays the interface status or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-729...
Page 778
When a TwinGig converter is enabled or disabled, the number and type of ports on the line card change dynamically. The terminology must reflect this behavior. In Cisco IOS, 10-Gigabit ports are named TenGigabit and 1-Gigabit ports are named Gigabit. Starting with Cisco IOS Release 12.2(40)SG, to avoid having ports named TenGigabit1/1 and Gigabit1/1, the 10-Gigabit and 1-Gigabit port numbers are independent.
Page 779
Chapter 2 show hw-module port-group Command Description hw-module port-group Selects either Gigabit Ethernet or Ten Gigabit Ethernet interfaces on your module. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-731...
Page 780
Executing the command on VSS member switch role = VSS Standby, id = 2 Active max-port-num-mode configuration is 2 In this mode, Line cards inserted in last 3 slots (8,9 and 10) will not be active Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-732 OL-30934-01...
Page 781
A reload of active supervisor is required to apply the new configuration. Related Commands Command Description hw-module uplink select Selects the 10-Gigabit Ethernet or Gigabit Ethernet uplinks on the Supervisor Engine V-10GE within the W-C4510R chassis. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-733...
When you enter the show idprom interface command, the output lines for Calibration type and Rx (receive) power measurement may not be displayed for all GBICs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-734 OL-30934-01...
Page 783
= GBIC does not support copper cables, or the length must be determined from the transceiver technology. Vendor name = CISCO-FINISAR Vendor OUI = 36965 Vendor Part No. = FTR-0119-CSC Vendor Part Rev. Wavelength = Not available Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-735...
Page 784
10GFC Code Byte 0 :0x0 10GFC Code Byte 1 :0x0 10GFC Code Byte 2 :0x0 10GFC Code Byte 3 :0x0 Transmission range in 10m :0x3E8 Fibre Type : Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-736 OL-30934-01...
Page 785
Supervisor Block Length = 24 Supervisor Block Checksum = 548 Feature Bits = 0x0000000000000000 Card Feature Index = 95 MAC Base = 0007.0ee5.2a44 MAC Count = 2 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-737...
Page 786
PowerSupply Block Version = 255 PowerSupply Block Length = 255 PowerSupply Block Checksum = 65535 Feature Bits = 0x00000000FFFFFFFF Current @ 110V = -1 Current @ 220V = -1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-738 OL-30934-01...
The show interfaces command shows the operating mode for an interface, but the show running-config command shows the configured mode for an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-740 OL-30934-01...
Page 790
The following example shows how to display status information for the interfaces on the supervisor engine: Switch# show interfaces status Port Name Status Vlan Duplex Speed Type Te1/1 connected full 10G 10GBase-LR Te1/2 connected full 10G 10GBase-LR Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-742 OL-30934-01...
Page 791
The output of the show interfaces GigabitEthernet command displays an extra 4 bytes for every packet that is sent or received. The extra 4 bytes are the Ethernet frame CRC in the input and output byte statistics. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-743...
Page 792
0 output buffer failures, 0 output buffers swapped out Router# Related Commands Command Description interface (virtual switch) Selects an interface to configure and enters the interface configuration mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-744 OL-30934-01...
The following example shows how to display the error counters for a specific module: Switch# show interfaces counters errors module 1 Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize Gi1/1 Gi1/2 Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts Giants Gi1/1 Gi1/2 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-745...
Page 794
10.00% 6278550 Switch# Related Commands Command Description show interfaces (virtual switch) Displays the interface capabilities for an interface or for all the interfaces on a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-746 OL-30934-01...
Page 795
• on this interface." If interface is omitted, the command displays the counters for all port channels (in the system) and • for their associated physical ports. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-747...
GigE to server farm Switch# Related Commands Command Description description (refer to Cisco IOS Includes a specific description about the digital signal documentation) processor (DSP) interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-750 OL-30934-01...
Gi3/6 1 minute 28 secs Gi4/1 1 minute 28 secs In this example, the cable has been disconnected from the port for 1 minute and 28 seconds. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-751...
Gi1/2 1500 Switch> Related Commands Command Description Enables jumbo frames on an interface by adjusting the maximum size of a packet or maximum transmission unit (MTU). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-752 OL-30934-01...
Page 801
VLAN and a secondary VLAN. private-vlan mapping Creates a mapping between the primary and the secondary VLANs so that both share the same primary VLAN SVI. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-753...
Switch# show interfaces status err-disabled Port Name Status Reason Err-Disabled VLANs ---- ---- ------ ------- ------------------- Fa9/4 notconnect link-flap Fa9/5 err-disabled psecure_violation Fa9/6 connected psecure_violation 10,15 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-754 OL-30934-01...
Page 803
Enables error-disable detection. hw-module port-group Selects either Gigabit Ethernet or Ten Gigabit Ethernet interfaces on your module. show errdisable recovery Displays error-disable recovery timer information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-755...
Page 805
(virtual switch) Displays the interface capabilities for an interface or for all the interfaces on a switch. show interfaces counters Displays the traffic on the physical interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-757...
The transceiver is in a module that supports diagnostic monitoring. If you notice that the alarm and warning flags have been set on a transceiver, reenter the command to confirm. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-758 OL-30934-01...
Page 810
Related Commands Command Description show idprom Displays the IDPROMs for the chassis. show interfaces status Displays the interface status or a list of interfaces in error-disabled state. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-762 OL-30934-01...
Fa5/48 routed negotiate routed Port Vlans allowed on trunk Fa5/1 none Fa5/2 none Fa5/3 none Fa5/4 none Fa5/5 none Fa5/6 none Fa5/7 none Fa5/8 Fa5/9 1-1005 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-763...
Page 812
1-1005 Port Vlans allowed and active in management domain Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8 02,850,917,999,1002-1005 Port Vlans in spanning tree forwarding state and not pruned Fa5/9 1-6,10,20,50,100,152,200,300,303-305,349-351,400,500,521,524,570,801-8 02,850,917,999,1002-1005 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-764 OL-30934-01...
31753 102407 102407 Vlan DHCP Permits ACL Permits Source MAC Failures ---- ------------ ----------- ------------------- 31753 Vlan Dest MAC Failures IP Validation Failures ---- ----------------- ---------------------- Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-765...
Page 814
The following example shows how to display the trust state of Fast Ethernet interface 6/1: Switch# show ip arp inspection interfaces fastEthernet 6/1 Interface Trust State Rate (pps) Burst Interval --------------- ----------- ---------- -------------- Fa6/1 Untrusted Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-766 OL-30934-01...
Page 815
Defines an ARP access list or adds clauses at the end of a predefined list. clear ip arp inspection log Clears the status of the log buffer. show ip arp inspection log Displays the status of the log buffer. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-767...
Switch# show ip arp inspection log Total Log Buffer Size : 10 Syslog rate : 0 entries per 10 seconds. No entries in log buffer. Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-768 OL-30934-01...
Page 817
Defines an ARP access list or adds clauses at the end of a predefined list. clear ip arp inspection log Clears the status of the log buffer. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-769...
----------- ---------------- ------------- ----- ------------ 0000.0100.0201 10.0.0.1 1600 dhcp-snooping FastEthernet3/1 Switch# The following example shows how to display an IP address for DHCP snooping binding entries: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-772 OL-30934-01...
Page 821
Switch# show ip dhcp snooping binding 172.100.101.102 MacAddress IP Address Lease (seconds) Type VLAN Interface ----------- ----------- ---------------- ------------- ----- ------------ 0000.0100.0201 172.100.101.102 1600 dhcp-snooping FastEthernet3/1 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-773...
Page 822
Type Binding type; statically configured from CLI or dynamically learned. VLAN VLAN number of the client interface. Interface Interface that connects to the DHCP client host. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-774 OL-30934-01...
Page 823
Enables DHCP snooping on a VLAN or a group of VLANs. ip igmp snooping Enables IGMP snooping. ip igmp snooping vlan Enables IGMP snooping for a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-775...
Last Failed Reason : No failure recorded. Total Attempts Startup Failures : Successful Transfers : Failed Transfers : Successful Reads Failed Reads Successful Writes Failed Writes Media Failures Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-776 OL-30934-01...
Page 825
Enables DHCP snooping on a trusted VLAN. ip dhcp snooping vlan Enables DHCP snooping on a VLAN or a group of VLANs. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-777...
IGMP snooping immediate-leave is disabled on this Vlan IGMP snooping mrouter learn mode is pim-dvmrp on this Vlan IGMP snooping is running in IGMP-ONLY mode on this VLAN Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-778 OL-30934-01...
Page 827
Deletes the IGMP group cache entries. show ip igmp snooping mrouter Displays information on the dynamically learned and manually configured multicast switch interfaces. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-779...
Switch# show ip igmp profile IGMP Profile 3 range 230.9.9.0 230.9.9.0 IGMP Profile 4 permit range 229.9.9.0 229.255.255.255 Switch# Related Commands Command Description ip igmp profile Creates an IGMP profile. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-780 OL-30934-01...
VLAN that has IGMP snooping enabled. You can display IGMP snooping information for VLAN interfaces by entering the show ip igmp snooping command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-781...
The following example shows how to display IGMP querier information for all VLANs on a switch: Switch# show ip igmp snooping querier Vlan IP Address IGMP Version Port --------------------------------------------------- 10.10.10.1 Router 172.20.50.22 Fa3/15 Switch> Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-782 OL-30934-01...
Page 831
Source information for group 226.6.6.7: Timers: Expired sources are deleted on next IGMP General Query SourceIP Expires Uptime Inc Hosts Exc Hosts ------------------------------------------------------- 2.0.0.1 00:03:04 00:03:48 2.0.0.2 00:03:04 00:02:07 Switch> Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-783...
Page 832
Configures a Layer 2 interface as a member of a group. show ip igmp interface Displays the information about the IGMP-interface status and configuration. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-784 OL-30934-01...
Page 833
Displays information on the dynamically learned and manually configured multicast switch interfaces. show mac-address-table multicast Displays information about the multicast MAC address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-785...
VLAN. show ip igmp interface Displays the information about the IGMP-interface status and configuration. show mac-address-table multicast Displays information about the multicast MAC address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-788 OL-30934-01...
IGMP snooping immediate-leave is disabled on this Vlan IGMP snooping mrouter learn mode is pim-dvmrp on this Vlan IGMP snooping is running in IGMP_ONLY mode on this Vlan Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-789...
Page 838
Displays information on the dynamically learned and manually configured multicast switch interfaces. show mac-address-table multicast Displays information about the multicast MAC address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-790 OL-30934-01...
Extended to include the 10-Gigabit Ethernet interface. Usage Guidelines The Cisco IOS software automatically enters a directly connected route in the routing table if the interface is usable. A usable interface is one through which the software can send and receive packets.
Page 840
Outgoing access list Status of whether the interface has an outgoing access list set. Inbound access list Status of whether the interface has an incoming access list set. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-792 OL-30934-01...
Page 841
Status of whether packets that are targeted for an interface are disabled excluded from being redirected to a cache engine. Netflow Data Export (hardware) NDE hardware flow status on the interface. is enabled Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-793...
Connected (C) flag—When set on a route, the C flag has the same meaning as the S flag, except that the C flag indicates that only packets sent by directly connected hosts to the route should be signaled to a protocol process. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-794 OL-30934-01...
Page 843
Forwarding (F)—Used with the A flag as described above. The set of forwarding interfaces together • form a multicast olist or output interface list. Signaling (S)—Set on an interface when a multicast routing protocol process in Cisco IOS needs to • be notified of ingress packets on that interface.
In creating (S,G) entries, the software uses the best path to that destination group found in the unicast routing table (through Reverse Path Forwarding (RPF). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-797...
Page 847
Status of the software; indicates if the software is registered for a multicast source. T - SPT-bit set Status of the packets; indicates if the packets been received on the shortest path source tree. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-799...
Page 848
IP multicast routing table. expires How long (in hours, minutes, and seconds) until the entry is removed from the IP multicast routing table on the outgoing interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-800 OL-30934-01...
Page 849
Description ip multicast-routing (refer to Cisco IOS Enables IP multicast routing. documentation) ip pim (refer to Cisco IOS Enables Protocol Independent Multicast (PIM) on an documentation) interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-801...
This output appears when you enter the show ip verify source interface fa6/3 command and the interface fa6/3 does not have a VLAN enabled for DHCP snooping: Interface Filter-type Filter-mode IP-address Mac-address Vlan --------- ----------- ----------- --------------- -------------- --------- fa6/3 inactive-no-snooping-vlan Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-803...
Page 852
10.0.0.2 aaaa.bbbb.cccc fa6/4 ip-mac active 11.0.0.1 aaaa.bbbb.cccd fa6/4 ip-mac active deny-all deny-all 12-20 fa6/5 ip-mac active 10.0.0.3 permit-all fa6/5 ip-mac active deny-all permit-all 11-20 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-804 OL-30934-01...
Page 853
Adds or deletes a static IP source binding entry. ip verify source Enables IP source guard on untrusted Layer 2 interfaces. show ip source binding Displays the DHCP snooping binding entries. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-805...
Page 854
(Optional) Identification number of the web cache service group being controlled by the cache. The number can be from 0 to 254. For web caches using Cisco cache engines, the reverse proxy service is indicated by a value of 99.
Page 855
The name or number of the access list that determines which packets will be redirected. Total Packets Denied Redirect Total number of packets that were not redirected because they did not match the access list. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-807...
Page 856
WCCP Clients Not Visible A list of clients in the service group that are not visible to the router and other clients in the service group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-808 OL-30934-01...
Page 857
The following is sample output from the show ip wccp web-cache command: Switch# show ip wccp web-cache Global WCCP information: Router information: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-809...
Page 858
The following example displays web cache engine information and WCCP router statistics for the web cache service: Switch# show ip wccp web-cache detail WCCP Client information: WCCP Client ID: 10.10.10.2 Protocol Version: State: Usable Redirection: Packet Return: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-810 OL-30934-01...
Page 859
Group access-list: -none- Total Messages Denied to Group: Total Authentication failures: Total Bypassed Packets Received: Service Identifier: 91 Number of Service Group Clients: Number of Service Group Routers: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-811...
Page 860
Enables support of the WCCP service for participation in a service group. ip wccp redirect Enables packet redirection on an outbound or inbound interface using WCCP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-812 OL-30934-01...
0/1/2 2020000.3 unicast GALIOS IPC:Card 2:Control 2020000.4 unicast GALIOS RFS :Standby 2020000.5 unicast Slave: Remote TTY Client Port 2020000.6 unicast GALIOS RF :Standby 2020000.7 unicast GALIOS RED:Standby Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-813...
Page 862
0 pak alloc failed, 0 memd alloc failed 0 no hwq, 1 failed opens, 0 hardware errors No regular dropping of IPC output packets for test purposes Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-814 OL-30934-01...
Page 863
The following sample output displays LDRA configuration details after initiating a DHCP session. The fields in the example below are self-explanatory. Device # show ipv6 dhcp-ldra statistics DHCPv6 LDRA client facing statistics. Messages received Messages sent Messages discarded Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-815...
Page 864
Enables LDRA functionality on an access node. ipv6 dhcp ldra attach-policy (VLAN) Enables LDRA functionality on a VLAN. ipv6 dhcp-ldra attach-policy Enables LDRA functionality on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-816 OL-30934-01...
Page 865
Only RA (Router Advertisement) and REDIR (Router Redirected packets) counters are supported in Note Cisco IOS Release 12.2(54)SG. Related Commands Command Description epm access control Configures access control. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-817...
This is an example of output from the show ipv6 mld snooping command. It displays snooping characteristics for all VLANs on the switch. Switch> show ipv6 mld snooping Global MLD Snooping configuration: ------------------------------------------- Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-818 OL-30934-01...
Page 867
Last listener query interval : 1000 Related Commands Command Description ipv6 mld snooping Enables IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping globally or on the specified VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-819...
(MLD) snooping globally or on the specified VLAN. ipv6 mld snooping vlan Configures IP version 6 (IPv6) Multicast Listener Discovery (MLD) snooping parameters on the VLAN interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-820 OL-30934-01...
This is an example of output from the show ipv6 mld snooping querier vlan command: Switch> show ipv6 mld snooping querier vlan 2 IP address : FE80::201:C9FF:FE40:6000 MLD version : v1 Port : Gi3/0/1 Max response time : 1000s Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-821...
Page 870
Configures IP version 6 (IPv6) MLD Topology Change Notifications (TCNs). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-822 OL-30934-01...
Page 871
The following example shows how to display the ISSU capabilities entries for the IP host ISSU client (clientid=2082): Switch# show issu capability entries 2082 Client_ID = 2082, Entity_ID = 1 : Cap_Entry = 1 : Cap_Type = 0 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-823...
Page 872
Entity_ID = 1 : Cap_Group = 1 : Cap_Entry = 1 Cap_Type = 0 Switch# Related Commands Command Description show issu clients Displays the ISSU clients. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-824 OL-30934-01...
Page 874
Client_Name = ISSU C4k GaliosRedundancy client Related Commands Command Description show issu capability Displays the ISSU capability for a client. show issu entities Displays the ISSU entity information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-826 OL-30934-01...
Page 875
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines Before attempting an ISSU, you should know the compatibility level between the old and the new Cisco IOS software versions on the active and the standby supervisor engines. ISSU will not work if the two versions are incompatible.
Page 876
Cisco IOS images, the two versions of the Cisco IOS images are declared “Incompatible”. This means that an in-service upgrade or downgrade between these versions is not possible. The systems operates in RPR mode during the period when the versions of Cisco IOS at the active and standby supervisor engines differ.
Page 877
List of Clients: Client Name Base/Non-Base ================================================ ISSU Proto client Base ISSU RF Base ISSU CF client Base ISSU Network RF client Base ISSU CONFIG SYNC Base Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-829...
Page 878
Number of Matrices in Table = 1 (1) Matrix for cat4500-ENTSERVICES-M(112) - cat4500-ENTSERVICES-M(112) ========================================== Start Flag (0xDEADBABE) My Image ver: 12.2(31)SGA Peer Version Compatibility ------------ ------------- 12.2(31)SGA Comp(3) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-830 OL-30934-01...
Page 879
Chapter 2 show issu comp-matrix Related Commands Command Description show issu clients Displays the ISSU clients. show issu sessions Displays ISSU session information for a specified client. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-831...
Page 880
Nego_Session_ID = 15 Nego_Session_Name = shared nego session Transport_Mtu = 4096 Ses_In_Use = 2 Switch# Related Commands Command Description show issu clients Displays the ISSU clients. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-832 OL-30934-01...
Page 881
Usage Guidelines Entity is a logical group of sessions with some common attributes (like capability list and message type). Currently, most ISSU clients on the Catalyst 4500 series switch have only one entity. Examples The following example shows how to display the entity information for a specified ISSU client:...
Page 882
Negotiation started at 00:01:07.688, duration is 0.148 seconds Switch# Related Commands Command Description show issu clients Displays the ISSU clients. show issu sessions Displays ISSU session information for a specified client. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-834 OL-30934-01...
Page 884
Chapter 2 show issu message Related Commands Command Description show issu clients Displays the ISSU clients. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-836 OL-30934-01...
Page 885
Message_MTU = 44 Message_Type = 2, Negotiated_Version = 1, Message_MTU = 4 Related Commands Command Description show issu sessions Displays ISSU session information for a specified client. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-837...
Page 886
Forces a change from the active supervisor engine to the standby supervisor engine and causes the newly active supervisor engine to run the new image specified in the issu loadversion command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-838 OL-30934-01...
Page 887
Session is bidirectional and a reliable connection is established between two endpoints. Sync-data and negotiation messages are sent to the peer endpoint through a session. On a Catalyst 4500 series switch, each ISSU-aware client has a maximum of one session at each endpoint.
Page 888
This command was introduced on the Catalyst 4500 series switch. Usage Guidelines It might take several seconds after the issu loadversion command is entered for Cisco IOS software to load onto the standby supervisor engine and the standby supervisor engine to transition to SSO mode. If you enter the show issu state command too soon, you might not see the information you need.
Page 889
Forces a change from the active supervisor engine to the standby supervisor engine and causes the newly active supervisor engine to run the new image specified. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-841...
Page 890
Expressions are case sensitive. For example, if you enter | exclude output, the lines that contain output do not appear, but the lines that contain Output appear. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-842...
Page 892
Related Commands Command Description l2protocol-tunnel Enables protocol tunneling on an interface. l2protocol-tunnel cos Configures the class of service (CoS) value for all tunneled Layer 2 protocol packets. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-844 OL-30934-01...
The LACPDUs Sent and Recv columns display the LACPDUs sent and received on each specific interface. • The LACPDUs Pkts and Err columns display the marker protocol packets. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-845...
Page 895
Related Commands Command Description lacp port-priority Sets the LACP priority for the physical interfaces. lacp system-priority Sets the priority of the system for LACP. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-847...
Page 896
Keyword right-to-use introduced on the Catalyst 4500 series switches Usage Guidelines Use this command to display license information and to help with troubleshooting issues related to Cisco IOS software licenses. It displays all the licenses in the system. This command also displays those features that are available but not licensed to execute (i.e., multiple license can be active but not in use (execute) simulteously).
Page 897
Evaluation total period: 8 weeks 4 days Evaluation period left: 8 weeks 3 days License State: Inactive License Count: Non-Counted License Priority: Low Store Index: 2 Store Name: Dynamic Evaluation License Storage Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-849...
Page 898
INFINITE_KEYS INFINITE_KEYS 1 JAN 2006 1 JAN 2035 NiL NiL SLM_CODE DEMO NiL NiL Ni NiL NiL 5_MINS NOTLOCKEDNOTLOCKEDHBL l1nG2zXePlBt,ifk7ZReL80LqzvzgRUCelWrBp41FC3jOKer6ZMT7XC4834W3Ev7fm1eXoWaK58t:oDeH5RI1V3dVE 2VpAnYb7WiKDz9En8PfrI7vewhayNbschEXBD9:tfPfir6GaALUFwsLxcqYzHuL2$AQEBIf8B///mCSo9+7kn+8zTC 3WX1YS9if+g0e8AjRRu1Jq3Kye4y8wv4c+Y9FHJ7Ro/mw7ERwqRqwInXo3s+nsLU7rOtdOxoIxYZAo3LYmUJ+MFzsq lhKoJVlPyEvQ8H21MNUjVbhoN0gyIWsyiJaM8AQIkVBQFzhr10GYolVzdzfJfEPQIx6tZ++/Vtc/q3SF/5Ko8XCY= Comment: Hash: 9w09jAFGBzi2w6XQCljLOBe2p+Y= Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-850 OL-30934-01...
Page 899
EULA is accepted by the user. Switch# show license right-to-use License Store: Built-In License Storage StoreIndex: 1 Feature: ipservices Version: 1.0 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-851...
Page 900
This is an example of the show license expiring command Switch# show license expiring License Store: Primary License Storage License Store: Dynamic License Storage StoreIndex: 0 Feature: entservices Version: 1.0 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-852 OL-30934-01...
Page 901
License Store: Primary License Storage StoreIndex: 1 Feature: ipbase Version: 1.0 License Type: Permanent License State: Active, In Use License Count: Non-Counted License Priority: Medium License Store: Dynamic License Storage Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-853...
Configures the link state group and enables link state tracking. link state group Configures the link state group and interface, as either an upstream or downstream interface in the group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-854 OL-30934-01...
Page 903
State Level Description Initialize Intermediate The state of the session when it initializes Acquiring Intermediate The state of the session when it is obtaining the client MAC address Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-855...
Page 904
The following example shows how to display MAB information for a specific interface: Switch# show mab interface GigaEthernet1/3 MAB details for GigaEthernet1/3 ------------------------------------- Mac-Auth-Bypass = Enabled Inactivity Timeout = None Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-856 OL-30934-01...
Page 905
Client MAC = 000f.23c4.a401 MAB SM state = TERMINATE Auth Status = AUTHORIZED Switch# Related Commands Command Description Enables and configures MAC authorization bypass (MAB) on a port. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-857...
Page 906
Outbound access-list is not set Related Commands Command Description access-group mode Specifies the override modes (for example, VACL overrides PACL) and the non-override modes (for example, merge or strict mode). Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-858 OL-30934-01...
Page 907
The keyword definitions for the protocol variable are as follows: ip specifies the IP protocol. • ipx specifies the IPX protocols. • assigned specifies the assigned protocol entries. • other specifies the other protocol entries. • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-859...
Page 908
Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-860 OL-30934-01...
Page 909
Displays the dynamic MAC address table entries only. show mac-address-table interface Displays the MAC address table information for a specific interface. show mac-address-table multicast Displays information about the multicast MAC address table. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-861...
Page 910
Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-862 OL-30934-01...
Page 911
Displays information about the multicast MAC address table. show mac-address-table protocol Displays the MAC address table information that is based on the protocol. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-863...
Page 912
Description show mac-address-table static Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-864 OL-30934-01...
Page 913
For the MAC address table entries that are used by the routed ports, the routed port name is displayed in the “vlan” column not the internal VLAN number. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-865...
Page 914
Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-866 OL-30934-01...
Page 915
FastEthernet6/16 0000.0000.0104 dynamic other FastEthernet6/16 0000.0000.0105 dynamic other FastEthernet6/16 0000.0000.0106 dynamic other FastEthernet6/16 Multicast Entries vlan mac address type ports -------+---------------+-------+------------------------------------------- ffff.ffff.ffff system Fa6/16 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-867...
Page 916
Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-868 OL-30934-01...
Page 917
The following example shows that MAC address learning is disabled on VLAN 200: Switch> show mac address-table learning VLAN Learning Status ---- --------------- Related Commands Command Description mac-address-table learning vlan Enables or disables MAC address learning on a VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-869...
Page 918
The following example shows how to display the number of multicast MAC entries for all VLANs: Switch# show mac-address-table multicast count MAC Entries for all vlans: Multicast MAC Address Count: Total Multicast MAC Addresses Available: 16384 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-870 OL-30934-01...
Page 919
Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-871...
Page 920
Number of Notifications sent to NMS : 3 Maximum Number of entries configured in History Table : 500 Current History Table Length : 3 MAC Notification Traps are Enabled Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-872 OL-30934-01...
Page 921
Enables MAC address notification on a switch. snmp-server enable traps Enables SNMP notifications (traps or informs). snmp trap mac-notification change Enables SNMP MAC address notifications. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-873...
Page 923
Displays information about the multicast MAC address table. show mac-address-table static Displays the static MAC address table entries only. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-875...
Page 924
• ip specifies the IP protocol. • ipx specifies the IPX protocols. • other specifies the other protocol entries. • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-876 OL-30934-01...
Page 925
Displays the number of entries currently in the MAC address table. show mac-address-table dynamic Displays the dynamic MAC address table entries only. show mac-address-table interface Displays the MAC address table information for a specific interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-877...
Page 926
Displays the MAC address table information that is based on the protocol. show mac-address-table vlan Displays information about the MAC address table for a specific VLAN. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-878 OL-30934-01...
Page 927
The keyword definitions for the protocol variable are as follows: assigned specifies the assigned protocol entries. • ip specifies the IP protocol. • ipx specifies the IPX protocols. • other specifies the other protocol entries. • Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-879...
Page 928
Displays the MAC address table information that is based on the protocol. show mac-address-table static Displays the static MAC address table entries only. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-880 OL-30934-01...
Page 929
The following example shows how to displaythe configuration of the MAC address group: Switch# show macro auto address-group MAC Address Group Configuration: Group Name MAC ADDRESS -------------------------------------------------------------- testGroup 2222.2222.2222 1111.1111.1111 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-881...
Page 930
Refer to the Command Reference in the IOS library manager show macro auto interface Display Auto SmartPorts status and the functions applied on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-882 OL-30934-01...
Page 931
Displays the default information for a device, including builtin function name and the parameters that can be provided for the commands when executing the builtin function. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-883...
Page 932
Configures macro default parameter values. macro auto execute (built-in Configures mapping from an event trigger to a built-in macro. function) macro auto global processing Enables Auto Smartports on a switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-884 OL-30934-01...
Page 933
Creates event triggers. show macro auto monitor type Displays all the device types recognized by the device classifier. show shell triggers Displays information about event triggers and macros. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-885...
Page 934
MAC address: Switch# show macro auto monitor device mac-address 001f.9e90.1250 MAC_Address Port_Id Profile Name ============== ======= ============================ 001f.9e90.1250 Gi1/0/4 Cisco-AP-Aironet-1130 ========================================================== Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-886 OL-30934-01...
Page 935
Displays all the device types recognized by the device classifier. show macro auto monitor type Displays all the device types recognized by the device classifier. show shell triggers Displays information about event triggers and macros. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-887...
Page 938
Displays all the device types recognized by the device classifier. show macro auto monitor device Displays all the device types recognized by the device classifier. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-890 OL-30934-01...
Page 944
....00f0 c6 c7 c8 c9 ca cb cc cd ce cf d0 d1 03 3e d0 33 .....>.3 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-896 OL-30934-01...
Displays all ports that are members of an MVR multicast group or, if there are no members, means the group is inactive. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-901...
Page 951
Configures MVR ports. show mvr Displays the global MVR configuration on the switch. show mvr members Displays all receiver ports that are members of an MVR multicast group. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-903...
This is an example of output from the show mvr members ip-address command. It shows how to view the members of the IP multicast group 239.255.0.2. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-904 OL-30934-01...
Page 953
Displays the configured MVR interfaces, status of the specified interface, or all multicast groups to which the interface belongs when the members keyword is appended to the command. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-905...
Page 955
(netflow-lite exporter submode) options timeout (netflow-lite Specifies an options timeout for the NetFlow-lite collector. exporter submode) export-protocol (netflow-lite Specifies the export protocol for the NetFlow-lite collector. exporter submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-907...
Page 956
These examples show how to display information about a particular packet or per data source stats: Switch# show netflow-lite monitor 1 interface gi1/3 Interface GigabitEthernet1/3: Netflow-lite Monitor-1: Active: TRUE Sampler: sampler1 Exporter: exporter1 Average Packet Size: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-908 OL-30934-01...
Page 957
Activates sampling on an interface in netflow-lite monitor submode) submode. exporter (netflow-lite monitor Assigns an exporter in netflow-lite monitor submode. submode) average-packet-size Specifies the average packet size at the observation point. (netflow-lite monitor submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-909...
Page 958
(netflow-lite Specifies a packet sampling rate in netflow-lite sampler submode. sampler submode) packet-offset (netflow-lite Specifies a starting packet offset in netflow-lite submode. sampler submode) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-910 OL-30934-01...
Page 959
This is an example of output from the show nmsp attachment suppress interface command: Switch# show nmsp attachment suppress interface NMSP Attachment Suppression Interfaces -------------------------------------- GigabitEthernet1/1 GigabitEthernet1/2 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-911...
Page 960
Failed socket read: 0 Socket read would block: 0 Transmit Q full: 0 Max Location Nofity Msg: 0 Max Attachement Notify Msg: 0 Max TX Q Size: 0 Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-912 OL-30934-01...
Page 961
-------- 172.19.35.109 Attachment, Location Switch# Related Commands Command Description clear nmsp statistics Clears the NMSP statistic counters. nmsp Configures Network Mobility Services Protocol (NMSP) on the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-913...
Fa5/6 Fa5/7 Switch# The following example shows how to display PAgP dual-active information: Switch# show pagp dual-active PAgP dual-active detection enabled: Yes PAgP dual-active version: 1.1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-914 OL-30934-01...
Page 963
2/48 11s SAC Switch# Related Commands Command Description pagp learn-method Learns the input interface of the incoming packets. pagp port-priority Selects a port in hot standby mode. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-915...
Page 964
Channel group 5 is not participating in PAGP Channel group 10 dual-active detect capability w/nbrs Dual-Active trusted group: Yes Dual-Active Partner Partner Partner Port Detect Capable Name Port Version Gi1/6/1 mr-rogers-nbr Gi1/5/1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-916 OL-30934-01...
Page 965
Dual-Active Partner Partner Partner Port Detect Capable Name Port Version Fa1/2/33 None None Router# Related Commands Command Description dual-active detection (virtual switch) Enables and configures dual-active detection. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-917...
Page 966
Displays class map information. show policy-map interface Displays the statistics and configurations of the input and output policies that are attached to an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-918 OL-30934-01...
Page 967
Match: access-group name system-cpp-eapol Class-map: system-cpp-bpdu-range (match-all) 0 packets Match: access-group name system-cpp-bpdu-range Class-map: system-cpp-cdp (match-all) 28 packets Match: access-group name system-cpp-cdp police: Per-interface Conform: 530 bytes Exceed: 0 bytes Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-919...
Page 968
Class-map: system-cpp-dhcp-sc (match-all) 0 packets Match: access-group name system-cpp-dhcp-sc Class-map: system-cpp-dhcp-ss (match-all) 0 packets Match: access-group name system-cpp-dhcp-ss Class-map: class-default (match-any) 0 packets Match: any 0 packets Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-920 OL-30934-01...
Page 969
Related Commands Command Description control-plane Enters control-plane configuration mode. service-policy input (control-plane) Attaches a policy map to a control plane for aggregate control plane services. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-921...
Page 971
Switch(config-if)# service-policy input p1 Switch(config-if)# end Switch# write memory Switch# show policy-map interface FastEthernet6/1 class-map c1 match flow ip source-address ip destination-address ip protocol l4 source-port l4 destination-port policy-map p1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-923...
Page 972
Creates a policy map that can be attached to multiple ports to specify a service policy and to enter policy-map configuration mode. show class-map Displays class map information. show qos Displays QoS information. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-924 OL-30934-01...
Page 973
The following example shows how to display policy-map statistics on VLAN 100 on the FastEthernet interface: Switch# show policy-map interface fastEthernet 6/1 vlan 100 FastEthernet6/1 vlan 100 Service-policy input: p1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-925...
Page 974
Attaches a policy map to an interface. show policy-map interface Displays the statistics and configurations of the input and output policies that are attached to an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-926 OL-30934-01...
Page 975
You can also use this command to display all the MAC addresses for an interface even if you have not enabled port security on it. Sticky MAC addresses are addresses that persist across switch reboots and link flaps. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-927...
Page 977
Switch# show port-security interface gigabitethernet1/1 address vlan 2-3 Secure Mac Address Table ------------------------------------------------------------------------ Vlan Mac Address Type Ports Remaining Age(mins) ---- ----------- ---- ----- ------------- 0001.0001.0001 SecureConfigured Gi1/1 0001.0001.0002 SecureSticky Gi1/1 Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-929...
Page 978
Fast Ethernet port 1 with aging information for each address: Switch# show port-security interface fastethernet5/1 address vlan 2-3 Secure Mac Address Table ------------------------------------------------------------------------ Vlan Mac Address Type Ports Remaining Age(mins) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-930 OL-30934-01...
Page 979
The following example shows how to display the port security settings on interface Gigabitethernet1/1 for VLANs 2 and 3: Switch# show port-security interface gigabitethernet1/1 vlan 2-3 Default maximum: 22 VLAN Maximum Current Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-931...
Page 980
0001.0001.0001 SecureConfigured Gi1/1 0001.0001.0002 SecureSticky Gi1/1 0001.0001.0003 SecureSticky Gi1/1 ------------------------------------------------------------------------ Total Addresses: 12 Switch# Related Commands Command Description switchport port-security Enables port security on an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-932 OL-30934-01...
The show power inline interface | module command displays the amount of power that is used to operate a Cisco IP Phone. To view the amount of power requested, use the show cdp neighbors command. Because FPGAs and other hardware components on the WS-X4548-RJ45V+ and WS-X4648-RJ45V+E modules consume PoE, the operating PoE consumption for an 802.3af-compliant module can be nonzero...
Page 982
The following example shows how to verify the PoE consumption for the switch: Switch# show power inline consumption default Default PD consumption : 5000 mW Switch# The following example shows how to display the status of inline power: Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-934 OL-30934-01...
Page 983
Switch# show power detail sh power detail Power Inline Supply Model No Type Status Sensor Status ------ ---------------- --------- ----------- ------- ------- PWR-C45-1400DC DCSP1400W good good n.a. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-935...
Page 984
---- ----------------- --------- ------------ -------- WS-X4013+TS WS-X4506-GB-T WS-X4424-GB-RJ45 Fan Tray ----------------------- --------- ------------ ------- Total Watts used of Chassis Inline Power (-50V) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-936 OL-30934-01...
Page 985
Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E JAE1132SXRP 10/100/1000BaseT POE E Series WS-X4648-RJ45V-E JAE114740YF M MAC addresses Status --+--------------------------------+---+------------+----------------+-- 1 0017.94c8.f580 to 0017.94c8.f585 0.4 12.2(44r)SG( 12.2(52) Ok Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-937...
Page 986
Inline Power Mode: auto Operational status: off Device Detected: no Device Type: n/a IEEE Class: n/a Discovery mechanism used/configured: Ieee and Cisco Police: off Power Allocated Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-938 OL-30934-01...
Page 987
Maximum Power drawn by the device since powered on: 0.0 Absent Counter: 0 Over Current Counter: 0 Short Current Counter: 0 Invalid Signature Counter: 0 Power Denied Counter: 0 Interface: Gi3/6 Inline Power Mode: auto Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-939...
Page 988
Sets the default power that is allocated to an interface for all the inline-power-capable interfaces on the switch. power redundancy-mode Configures the power settings for the chassis. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-940 OL-30934-01...
Page 989
Power --------- ------ ---------- ---------- ---------- ------ ----- Gi2/1 auto errdisable ok 22.6 Related Commands Command Description power inline police Configures PoE policing on a particular interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-941...
Page 991
Enables the PPPoE Intermediate Agent feature on an interface. (interface) pppoe intermediate-agent Sets circuit-id or remote-id for an interface. format-type (interface) Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-943...
The following example shows the output that might be displayed if you do not enter any keywords: Switch# show qos QoS is enabled globally Switch# Related Commands Command Description qos account layer-all encapsulation Globally enables QoS functionality on the switch. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-944 OL-30934-01...
Operational Port Trust State: ‘untrusted’ Port Trust Device:'cisco-phone' Default DSCP:0 Default CoS:0 Tx-Queue Bandwidth ShapeRate Priority QueueSize (bps) (bps) (packets) 31250000 disabled 31250000 disabled 31250000 disabled normal 31250000 disabled Switch# Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-947...
Page 996
Chapter 2 show qos interface Related Commands Command Description show qos Displays QoS information. tx-queue Configures the transmit queue parameters for an interface. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-948 OL-30934-01...
Image Version = Cisco Internetwork Operating System Software IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I5S-M), Version 12.2(20)EWA(3 .92), CISCO INTERNAL USE ONLY ENHANCED PRODUCTION VERSION Copyright (c) 1986-2004 by cisco Systems, Inc. Catalyst 4500 Series Switch Cisco IOS Command Reference—Release XE 3.9.xE and 15.2(5)Ex 2-951...