Honda Civic Service Manual page 50

MEASUREMENT
,n7 _--
STANDAFO INEW}
0.07 10.003) max.
75.00 75.02 (2.953 - 2.954)
7 4.9A0 7 4.990 t2.9520 2.95241
0.010 - 0.040 (0.0004 0.0016)
1.020 - 1.030 10.0402 _ 0.0406)
1.220 1.230 (0.0480 - 0.0484)
2 . 8 0 5 - 2 . 8 2 0 { 0 . 1 1 0 4 _ 0 . 1 1 t O )
0.035 - 0.060 (0.0014 0.0024)
0.030 - 0.055 {0.0012 0.0022)_
0.15 0.30 {0.006 _ 0.012)
0 . 3 0 - 0 . 4 5 ( 0 . 0 1 2 - 0 . 0 1 8 )
0.20 - 0.70 10.008 0.028)
18.994 - 19.000 (0.7478 _ 0.7480)
0.010 - 0 0?2 lo oona -n dn^ol
SERVICE LIMIT
0.10 (0.004)
75.07 (2.956)
0.05 (0.002)
0.5 (0.02)
74.970 (2.9516)
0.05 (0.002)
1 . 0 5 ( 0 . 0 4 1 )
1 . 2 5 1 0 . 0 4 9 )
2.85 (0.112)
0 . 1 3 { 0 . 0 0 5 )
0.13 (0.005)
0.60 (0.024)
0.70 (0.028)
ljqql)
_
oro to.o',ur
0.005 (0.0002)
0.005 (0.0002)
0 . 4 5 1 0 . 0 1 8 )
0.04 (0.002)
0.05 (0.002)
0.05 {0.002)
0.05 (0.002)
Cylinder block
Warpage of deck surface
Bore diameter
Bore taper
Reboring limit
Skirt O.D. at 5 mm (0.2 in)
from bottom of skin
Clearance in cylinder
Groove width {for ring)
Top
Second
o i l
Ring to-groove clearance Top
Second
R i n g e n d g a p
Top
Second
o i l
o.D.
Pin-to piston clearance
Pin-to rod interference
Small end bore diameter
Large end bore diameter Nominal
End play installed on crankshaft
Piston
Piston ring
Piston pin
Connecting
rod
0.014 - 0.040 (0.0006 _ 0.ool6)
18.96 - 18.98 (0.746 0.747)
4 8 . 0 1 1 . 8 9 )
0.15 - 0.30 (0.006 - 0.012)
C r a n k s h a f t M a i n j o u r n a l d i a m e t e r
R o d i o u r n a l d i a m e t e r
Taper
Out of-round
End play
Total runout
Main bearing to-lournal o't clearance-
N o _ l a n d 5 j o u r n a l s
_
N o . 2 , 3 a n d 4 j o u r n a t s
Bod bearing to,journat oil ctearance
54.976 - s5.000 (2.1644 - 2.1654)
44.91 6 - 45.000 1'1.17
01 _ 1.71 11 1
0.002510.0001)
max.
0.0025 (0.0001)max.
0.10 - 0.35 (0.004 0.014)
0.03 (0.001) max.
Bea.ings
0.018 - 0.036 (0.0007 0.0014)
0.024 0.042 (0.0009 - 0.0017)
0.020 - 0.038 (0.0008 _ o.oo.t5)
Standards and Service Limits
Engine Block {Dl6Y5, D16Y7, Dt6y8 enginesl - Section
L ,
L O
3-4
L O