Honda Civic Service Manual page 201

lllustrated Index
I
runricate att internal parts with engine oil during reassembly'
NOTE:
o Apply liquid gaskettothe mating surfaces ofthe right side cover and oil
pumpcase before installingthem'
.
U s e l i q u i d g a s k e t , p a r t N o 0 8 7 1 8 - 0 0 0 1 o r 0 8 7 1 8 - 0 0 0 3 '
. Clean the oil pan gasket mating surfaces betore installing the oil
pan
81642 engine:
DRAIN BOLT
44 N,m {4.5 kgf'm,33 lbt'ft)
6 x 1 . 0 m m
' 1 1 N . m ( 1 . 1 k g I ' m ,
I tbl.ft)
OIL PAN
Reter to page 7 27
when installing.
6 r 1 . O m m
12 N.m t1.2 kgl'm, 8 7 lbf'lt)
OIL PAN GASKET
BUFFLE PLA
1 2 x 1 . 0 m m
1 0 3 N . m { 1 0 . 5 k g f ' m ,
76 tbr.ft)
6 x 1 . 0 m m
1 1 N . m ( 1 . 1 k g f . m ,
8 tbI.fr)
GASKET
Replace.
FLYWHEEL
(M/TI
1 2 x 1 . 0 m m
7 4 N . m ( 7 . 5
kof.m, 54 lbf'ft)
1^
c{Eb
\%^
t*^
*o"rr^--(Wffi
oa*,trto2,.w
FLYWHEEL COVER
IM/T)
DRIVE PLATE
COVER (AiT)
1 1 x 1 . 5 m m
76 N.m (7.9 kgf'm, 56 lbf'ft)
Apply engine oil to the bolt
threads.
NOTE: After torqurng
each cap, turn crankshaft
to check for binding.
MAIN EEARING CAP
MAIN BEARINGS
Selection, page 7_10
NOTE: New main bearings musl
be selected bY matching crank
and block identification markrngs
CRANKSHAFT
Installation, Page 7'23
OIL JET BOLT
16 N.m 11.6 kgf'm, 12 lbl'ft)
OIL JET
Inspection, Page 8_10
Check for cracks
6 x 1 . 0 m m
1 1 N . m { 1 . 1 k g f ' m , I l b f ' f t }
CRANKSHAFT OIL SEAL
Installation,
p a g e s l 2 2 a n d l 2 9
Replace-
DOWEL PIN
OIL PUMP
Overhaul, page 8-'l1
Removal/lnspection,
page 8-13.
Apply liquid gasket
to mating surlace.
RIGHT SIDE COVER
Apply liquid gasket
to mating surface.
THRUST WASHERS
8 x 1 . 2 5 m m
24 N.m {2.4 kgf.m, 17 lbf'ft)
Grooved sides face outward
NOTE: Thrusr washer thickness
is tixed and must not be changed
by grinding or shimming
O-RING
Replace
CRANKSHAFT SEAL
1 1 N . m { 1 . 1 k g f ' m ,
l n s t a l l a t i o n , p a g e s 7 ' 2 9 a n d I 1 4
a l b t . l t l H e p l a c e .
( c o n t ' d )
d # *