Mitsubishi Electric FR-A800 Series Instruction Manual page 896

*2 Operation command
This signal is assigned in the initial status. The description changes depending on the setting of Pr.180 to Pr.189 (Input terminal function
selection). (Refer to
b15
-
<32-bit data>
No.
H0200 reserved
H0201 Output frequency (0-15 bit)
H0202 Output frequency (16-31 bit)
H0203 Setting frequency (0-15 bit)
H0204 Setting frequency (16-31 bit)
H0205 Motor rotation (0-15 bit)
H0206 Motor rotation (16-31 bit)
H0207 Load meter (0-15 bit)
H0208 Load meter (16-31 bit)
H0209 Positioning pulse (0-15 bit)
H020A Positioning pulse (16-31 bit)
H020B Watt-hour meter (1 kWh step) (0-15 bit)
H020C Watt-hour meter (1 kWh step) (16-31 bit)
Watt-hour meter (0.1/0.01 kWh step) (0-15
H020D
bit)
Watt-hour meter (0.1/0.01 kWh step) (16-
H020E
31 bit)
H020F Position error (0-15 bit)
H0210 Position error (16-31 bit)
H0211 Position command (lower 16 bits)
H0212 Position command (upper 16 bits)
H0213 Current position (lower 16 bits)
H0214 Current position (upper 16 bits)
H0215 to
reserved
H03FF
 Error reset and Ready bit status selection
• An error reset command from a communication option can be invalidated in the External operation mode or the PU
operation mode.
• The status of Ready bit is selectable.
Pr.
349
N010
N240
N241
N242
• The status of Ready bit in communication data can be changed when an HMS network option is installed. (P.N240)
• When an HMS network option is installed and the communication option is specified for the command source in Network
operation mode, it is possible to select whether the inverter is reset after the "Fault reset" command is executed. (P.N241)
Downloaded from ManualsNet.com
page 521.)
- - - RES
(STOP)
Description
Name
Communication reset
selection/Ready bit
status selection
Communication reset
selection
Ready bit status
selection
Reset selection after
inverter faults are
cleared
DriveControl writing
restriction selection
search engine
STP
CS JOG MRS
Unit Type
- -
0.01 Hz signed
0.01 Hz signed
1 r/min signed
0.1% signed
1 signed
1 kWh unsigned
0.1/0.01 kWh unsigned
1 signed
1 signed
1 signed
- -
Initial value Setting range
0, 1, 100, 101,
1000, 1001,
1100, 1101,
0 10000, 10001,
10100, 10101,
11000, 11001,
11100, 11101
0
0
1
0
0
1
0
0
1
0
0
1
RT RH RM RL
Read/ write
-
R
R
R
R
R/W
R
R
R
R
R
-
Description
Use this parameter to select the error reset
operation, Ready bit status, and inverter reset
operation when a fault is cleared.
Enables the error reset function in any operation
mode.
Enables the error reset function only in the
Network operation mode.
The status of Ready bit in communication data
can be selected.
The inverter is reset when a fault is cleared.
The inverter is not reset when a fault is cleared.
DriveControl writing is not restricted.
DriveControl writing is restricted.
9.6 For customers using HMS network options
1
b0
- - AU
2
3
4
5
6
7
8
9
10
895
9. APPENDIX