Mitsubishi Electric FR-A800 Series Instruction Manual page 347

Pr.
(Multi-speed setting high-speed, middle-speed,
4 to 6
low-speed)
22 Stall prevention operation level
24 to 27 (Multi-speed setting speed 4 to speed 7)
52 Operation panel main monitor selection
54 FM/CA terminal function selection
55 Frequency monitoring reference
56 Current monitoring reference
*1
PWM frequency selection
72
Reset selection/Disconnected PU detection/PU
75
stop selection
77 Parameter write selection
*2
Operation mode selection
79
129 PID proportional band
130 PID integral time
133 PID action set point
134 PID differential time
158 AM terminal function selection
160 User group read selection
232 to 239 (Multi-speed setting speed 8 to speed 15)
*1
Soft-PWM operation selection
240
241 Analog input display unit switchover
268 Monitor decimal digits selection
271 High-speed setting maximum current
272 Middle-speed setting minimum current
273 Current averaging range
274 Current averaging filter time constant
Stop-on contact excitation current low-speed
*1
275
scaling factor
290 Monitor negative output selection
295 Frequency change increment amount setting
296, 297 (Password setting)
306 Analog output signal selection
310 Analog meter voltage output selection
*2
Communication startup mode selection
340
345, 346 (DeviceNet communication)
416, 417 (PLC)
434, 435 (CC-Link communication)
496, 497 (Remote output)
498 PLC function flash memory clear
*2
NET mode operation command source selection
550
*1 Writing during operation is enabled in PU operation mode, but disabled in External operation mode.
*2 Writing during operation is disabled. To change the parameter setting value, stop the operation.
 Parameter write disabled (Pr.77 = "1")
• Parameter write, Parameter clear, and All parameter clear are disabled. (Parameter read is enabled.)
• The following parameters can be written even if Pr.77 = "1".
Pr.
22 Stall prevention operation level
Reset selection/Disconnected PU detection/PU stop
75
selection
77 Parameter write selection
*1
Operation mode selection
79
160 User group read selection
296 Password lock level
297 Password lock/unlock
*1 Writing during operation is disabled. To change the parameter setting value, stop the operation.
346
5. PARAMETERS
5.7 (E) Environment setting parameters
Downloaded from ManualsNet.com
Name
Name
search engine
Pr.
*2
PU mode operation command source selection
551
555 to 557 (Current average value monitoring)
656 to 659 (Analog remote output)
663 Control circuit temperature signal output level
675 User parameter auto storage function selection
750, 751 Motor thermistor interface
759 PID unit selection
774 to 776 (PU/DU monitor selection)
805 Torque command value (RAM)
806 Torque command value (RAM, EEPROM)
838 DA1 terminal function selection
866 Torque monitoring reference
888, 889 (Free parameter)
891 to 899 (Energy saving monitoring)
C0 (900) FM/CA terminal calibration
C1 (901) AM terminal calibration
C8 (930) Current output bias signal
C9 (930) Current output bias current
C10 (931) Current output gain signal
C11 (931) Current output gain current
990 PU buzzer control
991 PU contrast adjustment
992 Operation panel setting dial push monitor selection
997 Fault initiation
*2
PM parameter initialization
998
*2
Automatic parameter setting
999
1000 Direct setting selection
1006 Clock (year)
1007 Clock (month, day)
1008 Clock (hour, minute)
1018 Monitor with sign selection
1019 Analog meter voltage negative output selection
1048 Display-off waiting time
1142 Second PID unit selection
1150 to 1199 (PLC function user parameters)
1283 Home position return speed
1284 Home position return shifting speed
Pr.
345, 346 (DeviceNet communication)
496, 497 (Remote output)
656 to 659 (Analog remote output)
805 Torque command value (RAM)
806 Torque command value (RAM, EEPROM)
997 Fault initiation
Name
Name