Table of Contents
Advertisement
Interactions (cont'd)
4.
BUSY VERIFICATION [B-3] and EXECUTIVE OVERRIDE [E-1]: These features will be denied for a
connection that includes the Paging route.
5.
DELAY OPERATION: Station A is connected to party B. Station A momentarily presses the switch hook
and dials the MEET-ME PAGE route access code. When connected to the page, Station A requests Station
C to dial the MEET-ME PAGE answer code. Station A hangs up. When Station C dials the answer code,
Station A is rung. Station C and Station A are connected. If Station A hangs up, Party B is connected to
Station C. If Station A momentarily presses the switch hook, all three parties are connected together in a
THREE-WAY CALLING [T-2] connection. If Station C does not call the MEET-ME PAGE answer code
after 30 seconds, Party B rings back to Station A.
6.
NON-DELAY OPERATION: Station A is connected to Party B. Station A momentarily presses the switch
hook and dials the MEET-ME PAGE route access code. When connected to the page, Station A requests
Station C to dial the MEET-ME PAGE answer code. Station A stays on the trunk and is still voice-
connected to the paging equipment. Station C dials the MEET-ME PAGE answer code. The paging trunk
becomes idle. Station A is connected to Station C. If Station A hangs up, Party B is connected to Station
C. If Station A momentarily presses the switch hook, all three parties are connected together in a THREE-
WAY CALLING [T-2] connection. There is no time-out period if Station C does not dial the MEET-ME
PAGE answer code. Station A may press the switch hook to disconnect the page trunk and reconnect to
Party B. If desired, Station A may hang up and Station A will be recalled by Party B.
7.
Stations allowed Priority Page, SFI = 57, will come into the paging route, except when the Attendant
Console is paging.
8.
To answer MEET-ME PAGE, while connected to another party, CALL HOLD [C-6] must be used.
THREE-WAY CALLING [T-2] is not allowed.
Programming
STEP 1:
ASYD - System Data 1, Index 73, Bits 0 and 1.
For MEET-ME PAGE, non-Delay service, Bit 0 = 1, Bit 1 = 0.
For MEET-ME PAGE, Delay service, Bit 0 = 0, Bit 1 = 1.
For MEET-ME PAGE, Delay service with call transfer, Bit 0 = 1, Bit 1 = 1.
See PAGING TRANSFER [P-10].
System Data 1, Index 73, Bit 3. Are PAGE cancel codes provided for each route? 0/1: Per route/
Common to all routes.
System Data 1, Index 74, Bit 0-3. Assign the cancel timer for unanswered page.
Assign data 00H for 30 seconds.
(0-F + 1) x 30 = Cancel Timer.
System Data 2, Index 1, Bits 0 & 1. Consultation Hold allowed or denied. 00: Denied; 01: Originating
and Terminating Calls allowed; Tandem Call Denied; 11: All calls allowed.
STEP 2:
ARTD - Assign the Paging route as shown below:
RT:1
1-OSGS
8-RLP
STEP 3:
ATRK - Assign the LENs, Paging Trunk Route Number, Trunk Number, and Tenant Number.
STEP 4:
MBTK - Assign the Make Idle status to the Paging Trunks.
NEAX2400 IPX Feature Programming Manual
NDA-24297, Issue 1
Meet-Me Paging
:2
2-ONSG
:3
:2
15-LSG
:0/1
5-TF
:1
6-TCL
M-1
:8
7-L/T
:1
Page 465
Advertisement
Table of Contents
