Siemens SINUMERIK 840C Installation Instructions Manual page 428

12.93
96
Note:
This machine data is not included in the machine data lists. During start-up in machine data
dialog, the machine data is set or altered as appropriate via the configuration setting.
Input of code number for the motor used. The relevant motor data are stored in the software
and are transferred to machine data MD 159 to MD 175 when the motor code number is
changed. If individual motor data (MD 159 to MD 175) must be changed, then the value 99
(non-Siemens motor) must be entered as the motor code number.
Table of motors:
Order No.
1PH6101-4NF4- x
1PH6101-4NG4- x
1PH6103-4NF4- x
1PH6103-4NG4- x
1PH6105-4NF4- x
1PH6105-4NG4- x
1PH6107-4NF4- x
1PH6107-4NG4- x
1PH6131-4NF4- x
1PH6131-4NG4- x
1PH6133-4NF0- x
1PH6133-4NF4- x
1PH6133-4NG4- x
1PH6135-4NF0- x
1PH6135-4NF4- x
1PH6135-4NG4- x
1PH6137-4NF4- x
1PH6137-4NG4- x
1PH6138-4NF0- x
1PH6138-4NF4- x
1PH6138-4NG4- x
1PH6161-4NF0- x
1PH6161-4NF4- x
1PH6161-4NG4- x
©
Siemens AG 1992 All Rights Reserved
SINUMERIK 840C (IA)
More user manuals on
Motor code number motor 1
Default value Lower input limit
101
Rated
speed
n in
rated
rev/min
1500
2000
1500
2000
1500
2000
1500
2000
1500
2000
1500
1500
2000
1500
1500
2000
1500
2000
1500
1500
2000
1500
1500
2000
ManualsBase.com
7 Drive Machine Data (SIMODRIVE Drive MD)
Upper input limit
99 332
Rated Rated
power current
P in kW in A
rated rated
(for T
=100 K)
3.7 12.5
4.7 13.7
5.5 17.9
7.0 19.4
7.5 22.5
9.5 25.3
9.0 26.9
11.5 29.8
9.0 27.2
12.0 32.1
11.0 26.7
11.0 31.3
14.5 37.5
15.0 35.0
15.0 41.3
20.0 50.6
18.5 50.2
24.0 57.8
22.0 51.5
22.0 61.0
28.0 66.1
22.0 53.5
22.0 60.8
28.0 68.1
6FC5197- AA50
7.1.2 MSD MD (data description - SW 3)
Active on
Power On
Units
–
No-load Code
current numer
in A
0
(for T
=100 K)
6.2 101
6.9 102
9.1 103
9.9 104
11.5 105
13.1 106
14.2 107
15.6 108
11.7 109
13.6 110
11.5 111
13.4 112
16.1 113
16.1 114
18.8 115
22.8 116
22.9 117
26.5 118
24.6 119
28.7 120
31.4 121
23.9 122
26.9 123
31.3 124
7–13