GE F650 Instruction Manual page 712

APPENDIX C
APPENDIX C DNP 3.0 PROTOCOL FOR F650C.1DNP 3.0 PROTOCOL SETTINGS
F650 units enable the user to program certain parameters related to DNP3 protocol. These parameters are called DNP3
protocol settings and can be modified from the front panel or from the Level 2 software. The F650 relay supports
communication with multiple masters (3) and maintains three separate groups of DNP3 settings. Each group of DNP3
settings is related to a single logical DNP3 slave device. The F650 relay is able to communicate simultaneously with up to
three different DNP3 master stations. Each master communicates with a different logical DNP3 slave, these logical slaves
appearing as separate physical DNP3 slaves. This is achieved by keeping separate set of settings, event queues and set of
states for each logical device.
Notice that it is necessary to set different DNP Address and TCP/UDP Port for each logical DNP3 slave device.
Time synchronization through DNP protocol is available from all three DNP masters that can communicate with F650.
However the date & time will be taken from only one master at the same moment. It is recommended to use only one
master to do time sync through DNP.
SETTING NO SETTING NAME
1 Physical Port
2 Address
3 IP Addr Client1 Oct1
4 IP Addr Client1 Oct2
5 IP Addr Client1 Oct3
6 IP Addr Client1 Oct4
7 IP Addr Client2 Oct1
8 IP Addr Client2 Oct2
9 IP Addr Client2 Oct3
10 IP Addr Client2 Oct4
11 IP Addr Client3 Oct1
12 IP Addr Client3 Oct2
13 IP Addr Client3 Oct3
14 IP Addr Client3 Oct4
15 IP Addr Client4 Oct1
16 IP Addr Client4 Oct2
17 IP Addr Client4 Oct3
18 IP Addr Client4 Oct4
19 IP Addr Client5 Oct1
20 IP Addr Client5 Oct2
21 IP Addr Client5 Oct3
22 IP Addr Client5 Oct4
23 TCP/UDP Port
24 Unsol Resp Function
25 Unsol Resp TimeOut
26 Unsol Resp Max Ret
27 Unsol Resp Dest Adr
28 Current Scale Factor
29 Voltage Scale Factor
30 Power Scale Factor
31 Energy Scale Factor
32 Other Scale Factor
33 Current Deadband
34 Voltage Deadband
35 Power Deadband
36 Energy Deadband
37 Other Deadband
38 Msg Fragment Size
39 Binary Input Block1
GEK-106310AB
DEFAULT VALUE RANGE
NONE NONE, COM1, COM2, NETWORK
255 0 to 65534, step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
0 0 to 255 step 1
20000 1 to 65535, step 1
DISABLED DISABLED, ENABLED
5 s 0 to 60 sec, step 1
10 1 to 255, step 1
200 0 to 65519, step 1
1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
1 0.00001, 0.0001, 0.001, 0.01, 0.1, 1, 10, 100, 1000, 10000
30000 0 to 65535, step 1
30000 0 to 65535, step 1
30000 0 to 65535, step 1
30000 0 to 65535, step 1
30000 0 to 65535, step 1
240 30 to 2048, step 1
CTL EVENTS 1-16 See the explanation below
F650 Digital Bay Controller
C.1 DNP 3.0 PROTOCOL SETTINGS
C
C-1