GE B30 Communications Manual page 443

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
Agnd CMV Ground current (fourth input in a current AC bank).
SRC 1 Ground Current phasor, in primary amperes.
AgndRMS MV Ground current RMS (fourth input in a current AC bank).
SRC 1 Ground Current RMS, in primary amperes.
AlgCap SPC Command for the Hi-Z Oscillography Force Algorithm Capture
AlmInd SPS An LED.
The LED ALARM operand.
AmpInd SPS An LED.
The LED CURRENT operand.
AnFailBeh ENG Setting to select the behavior of the RxGOOSE Analog when the sending device is
offline: 0 = Default Value, 1 = Last Known
AnFailVal ASG The value of the RxGOOSE Analog when the sending device is offline and the
FailBeh is set to "Default Value"
AnOutput1 MV Analog output
AnyPBOn SPS Indicates ANY PB ON operand state. When any of the user pushbuttons is
asserted, status is "true"; when none of the user pushbuttons are asserted, status
is "false."
AnyErr SPS Any of the self-test errors generated. The ANY SELF TESTS operand.
AnyGpsFail SPS The GPS signal failed or is not configured properly at any terminal.
The 87L DIFF GPS FAIL operand, which becomes On when the GPS signal failed or
is not configured properly at any terminal.
AnyPoleOpn SPS At least one pole is open. The BREAKER 1 ANY P OPEN operand.
AnyShotCnt SPS The first breaker close signal has been issued.
The AR SHOT CNT greater than zero operand.
APPID ING Expected value of APPID field in messages subscribed to by RxGOOSE#
The RxGOOSE1 ETYPE APPID setting.
ArBlk1 SPS Autoreclose Breaker number indicated by the data instance number is
temporarily disabled.
The AR BKR1 BLK operand and the AR1 BLK FROM MAN CLS operand.
ArcConfid1 INS Represents the Arc Confidence in percentage for Phase A, B, C, or N
ArcSuspect ACT Indicates suspected element has operated
AresRMS MV Residual Current RMS.
SRC 1 Neutral Current RMS, in primary amperes.
ArLO SPS Autoreclose is locked out. The AR LO operand.
Armed SPS Accidental energization. Occurs when the generator is offline with no fault
involved. The ACCDNT ENRG ARMED operand.
ArMod1 SPS Autoreclosec mode equals to the number indicated by the data instance number,
in this case 1 and 3 pole mode. The AR MODE = 1 operand.
ArRip SPS Autoreclose is in progress. The AR RIP operand.
ASupn1 SPS Indicates the state of current supervision.
The PHS DIST Z1 SUPN AB/BC/CA operand in Phase-To-Phase.
Asymmetry SPS Communications channel asymmetry detected.
The 87L DIFF CH ASYM DET operand, which becomes On when the differential
element's has detected substantial communications channel asymmetry.
AutoMod SPS Capacitor control in auto mode. The CAP 1 IN AUTO operand.
BadSt1 SPS Bad-status detected. The BREAKER/SWITCH BAD STATUS operand.
BatFail SPS The battery is not functioning. The BATTERY FAIL operand.
BDifAClc CMV B90 differential current
BiasMotLod MV Indicates thermal model biased motor load.
THERMAL MODEL BIASED MOTOR LOAD in x FLA.
BknRotClr SPC Command to Clear BROKEN ROTOR BAR DATA. TRUE= CLEAR BROKEN ROTOR BAR
DATA
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical nodes...
ACsrcMMXN
ACsrcMMXN
HiZPHIZ
LEDsIHMI
LEDsIHMI
GGIO3
GGIO3
Cmp8BtGAPC
UsrPbIHMI
LPHD
LinDfPDIF
Bkr0XCBR
Rec13pRREC
LGOS
Rec13pRREC, Rec3pRREC
HiZPHIZ
HiZPHIZ
ACsrcMMXU
Rec13pRREC, Rec3pRREC
AcdEnrPIOC
Rec13pRREC
Rec13pRREC, Rec3pRREC
PhsDisPDIS
LinDfPDIF
CapCtlGAPC
BkrΘXCBR, Bkr0XCBR,
Disc0XSWI, DiscΘXSWI,
GGIO3
LPHD
B_DifPDIF
MotThmPTTR
BknRotSVBR
3-205
3