Toshiba e-STUDIO206L Service Manual page 579

Error code Classification
CC91 Finisher related
service call
CC92
CC93
CC94
CCF1
CDE0
CDF0 Offset tray related
service call
CE00 Optional
communication
related service call
CE50 Process related
service call
CE90
CF10 Finisher related
service call
F070 Communication
related service call
F090 Circuit related
service call
F100_0 Other service call
F100_1
F100_2
F101_0
F101_1
F101_2
F101_3
F101_4
F101_5
F101_6
F101_7
F101_8
F101_9
F102
© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved
Contents
The detection of the home position of the gripper arm
ends abnormality.
The movable tray exceeds its upper limit.
Knurled roller shift solenoid abnormality: An abnormality
occurs in the knurled roller shift solenoid. [MJ-1032]
1st fan motor abnormality: The 1st fan motor is locked
abnormally. [MJ-1032]
Tray safety switch abnormality -
The tray safety switch turned on during tray operation
(moving up or down).
Paddle motor abnormality: The paddle motor does not
rotate properly.
Initialization error of the offset tray: The home position of
the separator cannot be detected when the power is
turned ON.
Communication error between finisher unit and puncher
unit: Communication error between the finisher controller
PC board and punch controller PC board.
Temperature/humidity sensor abnormality: The output
value of this sensor is out of a specified range.
Drum thermistor abnormality: The output value of the
drum thermistor-K is out of a specified range.
Communication module SRAM reading failure. [MJ-1101/
1107]
Communication error between System-CPU and Engine-
CPU
SRAM abnormality on the SYS board
HDD format error: Operation of HDD key data fails.
HDD format error: Encryption key data of either the SYS
board or the SRAM board for the SYS board are damaged.
HDD format error: Encryption key data of both the SYS
board and the SRAM board for the SYS board are
damaged.
HDD connection error (HDD connection cannot be
detected.)
Root partition mount error (HDD formatting fails.): The
HDD cannot be connected (mounted) caused by damage
to the areas in which the program is mainly stored.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to areas other than those
described in the F101_1 and F101_4 to F101_9 errors.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to areas other than those
described in the F101_1 and F101_4 to F101_9 errors.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the "/work" partition.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the "/registration"
partition.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the "/backup" partition.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the "/imagedata"
partition.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the "/storage" partition.
Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the "/encryption"
partition.
HDD start error: HDD cannot become 'Ready' state.
e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507
8 - 19
Troubleshooting
P. 8-188
P. 8-188
P. 8-189
P. 8-189
-
P. 8-189
P. 8-191
P. 8-150
P. 8-139
P. 8-139
P. 8-190
P. 8-190
P. 8-151
P. 8-192
P. 8-192
P. 8-193
P. 8-194
P. 8-194
P. 8-194
P. 8-194
P. 8-195
P. 8-196
P. 8-197
P. 8-198
P. 8-199
P. 8-200
P. 8-201
ERROR CODE AND TROUBLESHOOTING
8