Toshiba e-STUDIO206L Service Manual page 578

Error code Classification
CC01 Finisher related
service call
CC02
CC20
CC21
CC22
CC23
CC30
CC31
CC41
CC51
CC52
CC53
CC54
CC60
CC61
CC71
CC72
CC80
e-STUDIO206L/256/306/356/456/506 / 207L/257/307/357/457/507
ERROR CODE AND TROUBLESHOOTING
Contents
A model not supporting the Finisher is connected. Note
that this error is recognized in the communication
converter and is output.
Stack exit roller nip home position detection error: The
detection of the home position of the stack exit roller nip
ends abnormally. [MJ-1032/MJ-1033]
Saddle communication error [MJ-1106/1108]
The detection of the home position of the saddle stitch
3rd transport roller drive motor ends abnormally.
The detection of the home position of the saddle stitch
stapler unit ends abnormally.
An abnormal interruption of the encoder pulse of the
folding blade occurs.
Stack transport motor abnormality: The stack transport
motor is not rotating or the stack transport belt is not
moving normally. [MJ-1101/1107/MJ-1106/1108]
Transport motor abnormality: The transport motor is not
rotating or the stack transport roller -1 and -2 is not
rotating normally. [MJ-1101/1107/MJ-1106/1108]
Paper holder cam home position abnormality: The paper
holder cam is not at the home position. [MJ-1101/1107]
Sideways adjustment motor (M2) abnormality: Sideways
adjustment motor is not rotating or puncher is not shifting
normally. [MJ-1101/1106 (when MJ-6103 is installed), MJ-
1107/1108 (when MJ-6104 is installed)]
Skew adjustment motor (M1) abnormality: Skew
adjustment motor is not rotating or puncher is not shifting
normally. [MJ-1101/1106 (when MJ-6103 is installed), MJ-
1107/1108 (when MJ-6104 is installed)]
An abnormality occurs in the punch waste full sensor.
Hole punch registration sensor detection error: An
abnormality occurs in the hole punch registration sensor.
[MJ-1032/MJ-1033]
Punch motor abnormality: Punch motor is not rotating or
puncher is not shifting normally.]
Punch motor (M3) home position detection error: Punch
motor is not rotating or puncher is not shifting normally.
[MJ-1101/1106 (when MJ-6103 is installed), MJ-1107/
1108 (when MJ-6104 is installed)]
Punch ROM checksum error: Abnormality of checksum
value on Hole punch controller PC board is detected
when the power is turned on. [MJ-1101/1106 (when MJ-
6103 is installed), MJ-1107/1108 (when MJ-6104 is
installed)]
Punch RAM read/write error: Abnormality of checksum
value on Hole punch controller PC board is detected
when the power is turned on. [MJ-1101/1106 (when MJ-
6103 is installed), MJ-1107/1108 (when MJ-6104 is
installed)]
Rear alignment motor abnormality: The rear alignment
motor is not rotating or the rear alignment plate is not
moving normally. [MJ-1101/1107/MJ-1106/1108]
Rear alignment plate home position detection error: The
detection of the home position ends abnormally because
the rear alignment plate has not worked properly.
[MJ-1032/MJ-1033]
8 - 18
© 2011-2014 TOSHIBA TEC CORPORATION All rights reserved
Troubleshooting
-
P. 8-175
P. 8-176
P. 8-176
P. 8-177
-
P. 8-178
P. 8-178
P. 8-179
P. 8-180
P. 8-181
P. 8-182
P. 8-182
P. 8-185
P. 8-185
P. 8-186
P. 8-186
P. 8-186