Honda Civic Service Manual page 1018

26. Install the thrust washer, the thrust needle bearing'
and the thrust washer on the carrier assembly'
SNAP RING
THRUST SHIM,
2 5 x 3 1 m m
Selective Pan
21.
24.
RING GEAR
THRUST NEEDLE THRUST WASHERS
EEARING
CARRIER
ASSEMBLY
lnstallthe ring gear and the 25 x 31 mm thrust shim,
then installthe snaP rrng.
Verify that the outside diameter of the snap ring is
correct,
Maximum 30.7 mm (1.21 in)
SNAP RING
Measure the clearance between the 25 x 31 mm
thrust shim and the snaP rlng.
STANDARD: O.O5 - 0.11 mm (0.0020
- 0.00'8 in)
NOTE: Take measurements in at least three places'
and use the average as the actual clearance
29.
,**r#*,".
'- t
)
RING GEAR
14-341
30.
3 1 .
lf the clearance is out of tolerance, remove the 25 x
31 mm thrust shim and measure its thickness'
Select and install a new 25 x 31 mm thrust shim.
then recheck.
THRUST SHIM, 25 x 31 mm
snap nng.
RING
After replacing the 25 x 31 mm thrust shim, make
sure that the clearance is within tolerance and the
snap ring outside diameter is correct'
Install the disc spring in the direction shown'
S t a r t i n g w i t h a r e v e r s e b r a k e p l a t e , a l t e r n a t e l y
install the reverse brake plates and discs lnstall
selected reverse brake end plate, then install the
32.
33.
34.
REVERSE
END PLATE
BRAKE
Dtscs
SPRING
l n s t a l l i n t h i s d i r e c t i o n .
(cont'd)
REVERSE
PI-ATES
No.
Part Numb.l
Thickne*3
90451 - P4V - 000 1.05 mm (0.041 in)
B
9 0 4 5 2 - P 4 V - 0 0 0
1.12 mm (0.044 in)
c
90453-P4V-000
'1.19 mm (0.047 in)
D
90454 - P4V - 000
'l.26 mm (0.050 in)
9 0 4 5 5 - P 4 V - 0 0 0 1.33 mm (0.052 in)
F 90456-P4V-000
1.40 mm (0.055 in)
904s7-P4V-000
1.47 mm (0.058 in)
90458-P4V-000
1.54 mm (0.06'l in)
90459-P4V-000
'1.61 mm (0.063 in)
J
90460-P4V-000
1.68 mm (0.066 inl
K
9 0 4 6 1 - P 4 V - 0 0 0 1.75 mm (0.069 in)
90462-P4V-000
1.82 mm (0.072 in)
M
904a0-P4V-000
1.085 mm (0.0427 in)
N
9 0 4 8 1 - P 4 V - 0 0 0 1.155 mm (0.0454 in)
o
901a2-P4V-000
1.225 mm (0.0482 in)
90483-P4V-000
1.295 mm (0.0510 in)
o
9 0 4 8 4 - P 4 V - 0 0 0 1.365 mm (0.0537 in)
R
904a5-P4V-000
1.435 mm (0.0565 in)
90486-P4V-000
1.5O5 mm (0,0593 in)
T 90487-P4V-000
1.575 mm (0.0620 in)
90488-P4V-00{)
1.645 mm {0.0648 in)
90489-P4V-000
1.715 mm (0.0675 in)
90490-P4V-000
1.785 mm (0.0703 in)