Honeywell Fire-Lite Alarms ES-1000X Manual page 90

Programming
ANN-LED Options
ANN XXX
1=ENABLED
2=MODULES INSTALLED
3=AUTO-CONFIGURE
ANN XXX Screen #2
The first screen indicates that the ANN-LED at the selected ANN-BUS address is programmed to annunciate Alarms, Supervisories, and
Troubles for SLC Loop #1 addressable Detectors with addresses 1 through 10. The programming can be changed using ANN-LED Address
Screens 2 and 3.
Pressing 1 while viewing ANN-LED Address Screen #2 will program the annunciator module to annunciate either Point (addressable device
address) information or Zone information.
Pressing 2 while viewing ANN-LED Address Screen #2 will program the annunciator module to annunciate only Alarms for addressable
device addresses 1-30 or Alarms, Supervisories, and Troubles for addressable device addresses 1-10.
Pressing 1 while viewing ANN-LED Address Screen #3 will select the Point or Zone range to be annunciated - refer to the tables in "ANN-
LED Zone Option - Alarm Only (for use with ANN-RLED module)" on page 90 and "ANN-LED Point Option - Alarm Only (for use with
ANN-RLED module)" on page 91.
Pressing 2 while viewing ANN-LED Address Screen #3 will select either addressable detectors or addressable modules to be annunciated.
Pressing 3 while viewing ANN-LED Address Screen #3 will select the SLC loop with the addressable devices to be annunciated.
ANN-LED Zone Option - Alarm Only (for use with ANN-RLED module)
If Zone is selected as the module option, and the module is programmed to annunciate alarms only, the first ten LEDs on the first ANN-LED
module will display the system status information. The remaining 30 LEDs on the first module and the last 30 LEDs on the remaining mod-
ules will display the active/alarm status of each zone in the Zone Range programmed for that particular module. The LED assignments for
each ANN-LED module will be as follows.
90
36 Point 026
37 Point 027
38 Point 028
39 Point 029
40 Point 300
Pressing 2 for Module Options while viewing the (XXX) ANN-BUS Address Screen when the ANN-LED
YES
option is selected, will display the following screen:
ANN-LED - ADDR X-1
SLC 1 DET 001-010
ALARM, TBL, SUPV
ANN-LED Address Screen #1
Alarm Silenced NAC 1 Fault
Earth Fault Battery Fault
Zone 000 Zone 001
Active/Alarm Active/Alarm
Zone 005 Zone 006
Active/Alarm Active/Alarm
Zone 010 Zone 011
Active/Alarm Active/Alarm
Zone 015 Zone 016
Active/Alarm Active/Alarm
Zone 020 Zone 021
Active/Alarm Active/Alarm
Zone 025 Zone 026
Active/Alarm Active/Alarm
Not Used Not Used
Not Used Not Used
Zone 030 Zone 031
Active/Alarm Active/Alarm
Zone 035 Zone 036
Active/Alarm Active/Alarm
Zone 040 Zone 041
Active/Alarm Active/Alarm
Zone 045 Zone 046
Active/Alarm Active/Alarm
Point 066 Point 106
Point 067 Point 107
Point 068 Point 108
Point 069 Point 109
Point 070 Point 110
ANN-LED - ADDR X-1
1=POINT/ZONE
2=ALARM/ATS
ANN-LED Address Screen #2
NAC 2 Fault
Charger Fault
Zone 002
Active/Alarm
Zone 007
Active/Alarm
Zone 012
Active/Alarm
Zone 017
Active/Alarm
Zone 022
Active/Alarm
Zone 027
Active/Alarm
Table 3.4 ANN-RLED Module #1
Not Used
Not Used
Zone 032
Active/Alarm
Zone 037
Active/Alarm
Zone 042
Active/Alarm
Zone 047
Active/Alarm
Table 3.5 ANN-RLED Module #2
ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023
Master Programming Level
Point 146 Not Used
Point 147 Not Used
Point 148 Not Used
Point 149 Not Used
Point 150 Not Used
ANN-LED - ADDR X-1
1=RANGE
POINT
2=DET/MOD
ATS
3=SLC LOOP #
ANN-LED Address Screen #3
NAC 3 Fault NAC 4 Fault
Disabled Maintenance
Zone 003 Zone 004
Active/Alarm Active/Alarm
Zone 008 Zone 009
Active/Alarm Active/Alarm
Zone 013 Zone 014
Active/Alarm Active/Alarm
Zone 018 Zone 019
Active Alarm Active/Alarm
Zone 023 Zone 024
Active/Alarm Active/Alarm
Zone 028 Zone 029
Active/Alarm Active/Alarm
Not Used Not Used
Not Used Not Used
Zone 033 Zone 034
Active/Alarm Active/Alarm
Zone 038 Zone 039
Active/Alarm Active/Alarm
Zone 043 Zone 044
Active/Alarm Active/Alarm
Zone 048 Zone 049
Active Alarm Active/Alarm
PT001-010
DET
1