1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Panel
  5. Fire-Lite Alarms ES-1000X
  6. Manual

Honeywell Fire-Lite Alarms ES-1000X Manual

Addressable fire alarm control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Addressable Fire Alarm Control Panel
ES-1000X
ES-1000XC
ES-1000XI
Manual
Document LS10133-000FL-E Rev: A
6/21/2023 ECN:00022081

Advertisement

Table of Contents
loading

Related Manuals for Honeywell Fire-Lite Alarms ES-1000X

Summary of Contents for Honeywell Fire-Lite Alarms ES-1000X

  • Page 1 Addressable Fire Alarm Control Panel ES-1000X ES-1000XC ES-1000XI Manual Document LS10133-000FL-E Rev: A 6/21/2023 ECN:00022081...
  • Page 2 Fire Alarm & Emergency Communication System Limitations While a life safety system may lower insurance rates, it is not a substitute for life and property insurance! An automatic fire alarm system—typically made up of smoke IMPORTANT! Smoke detectors must be installed in the same room detectors, heat detectors, manual pull stations, audible warning as the control panel and in rooms used by the system for the devices, and a fire alarm control panel (FACP) with remote...
  • Page 3 LiteSpeed™ and Lite-Connect™ are trademarks; and Fire-Lite® Alarms, Honeywell®, and SWIFT® are registered trademarks of Honeywell International Inc.Microsoft® and Windows® are registered trademarks of the Microsoft Corporation. Chrome™ and Google™ are trademarks of Google Inc. Firefox® is a registered trademark of The Mozilla Foundation.
  • Page 4 • Your suggestion for how to correct/improve documentation Send email messages to: FireSystems.TechPubs@honeywell.com Please note this email address is for documentation feedback only. If you have any technical issues, please contact Technical Services. This symbol (shown left) on the product(s) and / or accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

  • Page 5: Table Of Contents

    Table of Contents Section 1: Product Description ............................12 1.1: Features and Options .......................................12 1.2: Specifications........................................13 1.3: Controls and Indicators....................................15 1.4: Components ........................................15 1.4.1: Intelligent Addressable Detectors.................................16 1.4.2: Intelligent Addressable Modules ................................16 1.4.3: Addressable Device Accessories ................................16 End-of-Line Resistor Assembly................................16 Power Supervision Relay..................................16 EOL-C(R/W) Mounting Plate.................................17 1.5: Optional Modules ......................................17...
  • Page 6 Table of Contents ANN-RLY Annunciator Module ................................40 2.8.4: Printer ........................................42 Printer Configuration ....................................42 2.8.5: W-GATE(A) Wireless Gateway................................42 Section 3: Programming ..............................43 3.1: User Programming......................................44 3.2: Programming Screens Description ..................................44 3.3: Initial Power-up .......................................44 3.4: Users and Passwords......................................44 3.4.1: Administrator Role ....................................45 Password Change-Administrator ................................45 Password Change- User ..................................46 Assign Role......................................47...
  • Page 7 Table of Contents ANN-BUS Options ....................................94 3.5.9: Password Change....................................95 Invalid Password.....................................96 Incorrect Password/Timeout ...................................96 3.5.10: Clear Program.....................................96 3.5.11: Program Check ....................................96 3.6: Maintenance Programming Level..................................97 3.6.1: Disable Point......................................98 3.6.2: History ........................................98 3.6.3: Program Check .....................................99 3.6.4: Walktest ........................................99 3.6.5: System.........................................100 3.6.6: Zone Setup ......................................101 Section 4: Operating Instructions..........................
  • Page 8 Table of Contents Maintenance Alert....................................115 4.23.12: Time/Date .......................................116 4.23.13: Battery Charger....................................116 4.23.14: 4XTM Supervision ..................................116 4.23.15: Remote Sync....................................116 Section 5: Central Station Communications - POTS Transmission ................. 117 5.1: Transmittal Priorities .....................................117 Section 6: FS-Tools Upload/Download........................119 6.1: FS-Tools Up/Download ....................................119 6.2: Transferring a Program ....................................120 6.2.1: Security Features ....................................120 Time-out at Control Panel..................................120...
  • Page 9 It is imperative that the installer understand the requirements of the Authority Having Jurisdiction (AHJ) and be familiar with the standards set forth by the following regulatory agencies: • Underwriters Laboratories/Underwriters Laboratories Canada • National Fire Protection Association Before proceeding, the installer should be familiar with the following documents. NFPA Standards NFPA 72 National Fire Alarm Code NFPA 70 National Electrical Code...
  • Page 10 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 11 Peripheral Devices and Their Documents: ANN-100 ANN-RLY ANN-S/PG ANN-(R)LED ANN-I/O ANN-80 LCD Annunciator Relay Card Printer Driver LED Display LED Driver LCD Annunciator Doc. #LS10205-000FL-E Doc. #53033 Doc. #151417 Doc. #53032 Doc. #151416 Doc. #52749 ANN-BUS - TB9/TB10 IPOTS-COM POTS and IP Communicator TB17 Doc.

  • Page 12: Section 1: Product Description

    Section 1: Product Description The Fire-Lite ES-1000X is an addressable FACP (Fire Alarm Control Panel) with a pre-installed communicator card that is compact, cost effective, intelligent, and has an extensive list of powerful features.The combination of Fire-Lite’s newer series devices and legacy 300 Series devices, along with the ES-1000X FACP, offer the latest in fire protection technology.

  • Page 13: Specifications

    Specifications Product Description • Optional FS-Tools programming utility for local or remote Upload/Download of programming and data (available for download from www.firelite.com) • Compatible with Fire-Lite’s devices in LiteSpeed and CLIP mode (refer to SLC Wiring Manual for a list of compatible addressable devices) •...
  • Page 14 Product Description Specifications Remote Sync Output - TB8 Remote power supply synchronization output 24 VDC nominal special application power Maximum current is 350 mA End-of-Line Resistor: 4.7KΩ Output linked to NAC 1 control Supervised and power-limited circuit Programmable Class A or Class B wiring Primary ANN-BUS - TB9 Class A or Class B wiring ANN-BUS annunciator connector, Terminal 1 (+/A) and Terminal 2 (-/B)

  • Page 15: Controls And Indicators

    Controls and Indicators Product Description 1.3 Controls and Indicators LCD Display The FACP uses an 80-character (4 lines X 20 characters) high viewing angle LCD display. The display includes a long life LED backlight that remains illuminated. If AC power is lost and the system is not in alarm, the LED SYSTEM NORMAL backlight will turn off to conserve batteries.

  • Page 16: 1: Intelligent Addressable Detectors

    Product Description Components IPOTS-COM The IP/POTS Communicator card, standard on the ES-1000X and ES-1000XC, transmits system status (alarms, troubles, AC loss, etc.) to a Central Station via the public switched telephone network. It also allows remote programming or interrogation of the control panel using the ®...

  • Page 17: Eol-C(R/W) Mounting Plate

    Optional Modules Product Description EOL-C(R/W) Mounting Plate The EOL-CR (red) and EOL-CW (white) are single End-of-Line resistor plates which are required for use in Canada. An ELR, which is sup- plied with each module and fire alarm control panel, is mounted to the EOL-C(R/W) plate. Resistors mounted to the plate can be used for the supervision of a monitor and control module circuit.

  • Page 18: 4: W-Gate(A) Wireless Gateway

    Product Description Accessories 1.6.4 W-GATE(A) Wireless Gateway The W-GATE(A) Wireless Gateway acts as a bridge between a group of wireless fire devices and a LiteSpeed SLC loop on the ES-1000X. It is powered by the SLC loop or by a regulated, external 24VDC UL-listed power supply evaluated for life safety. Available wireless devices include a photo detector, a photo/heat detector, a fixed-temperature heat detector, a rate-of-rise heat detector, a monitor module, and a relay module.

  • Page 19: Getting Started

    Before connecting the control panel to the public switched telephone network, the installation of two RJ31X jacks is necessary. If trouble is experienced with this equipment, for repair or warranty information, please contact: Manufacturer: Honeywell International, Inc. One Fire-Lite Place Northford, CT 06472...

  • Page 20: 3: For Canadian Applications

    Product Description Telephone Requirements and Warnings 1.8.3 For Canadian Applications The following is excerpted from CP-01 Issue 5: NOTICE: The Industry Canada (IC) label identifies certified equipment. This certification means that the equipment meets certain telecom- munications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s).

  • Page 21: Section 2: Installation

    Section 2: Installation The cabinet may be either semi-flush or surface mounted. The cabinet mounts using two key slots and two 0.250” (6.35 mm) diameter holes located in the backbox. The key slots are located at the top of the backbox and the two securing holes at the bottom. Carefully unpack the system and check for shipping damage.
  • Page 22 Installation Mounting the Backbox 2.07” 1.875” 1.875” 2.25” 2.25” 2.25” 2.25” 1.875” 1.875” (5.26) (4.76) (4.76) (5.72) (5.72) (5.72) (5.72) (4.76) (4.76) Note: Values in 0.88” (2.24) parentheses are in centimeters (cm). 1.63” (4.14) Semi-Flush 6.755” Mounting (17.16) Do not recess box more than 3.875”...
  • Page 23 Mounting the Backbox Installation width depth height Left Side Right Side Bottom Figure 2.3 Cabinet Dimensions ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...

  • Page 24: Power

    Installation Power 2.2 Power WARNING: RISK OF EQUIPMENT DAMAGE AND PERSONAL INJURY SEVERAL DIFFERENT SOURCES OF POWER CAN BE CONNECTED TO THIS PANEL. DISCONNECT ALL SOURCES OF POWER BEFORE SERVICING. THE PANEL AND ASSOCIATED EQUIPMENT MAY BE DAMAGED BY REMOVING AND/OR INSERTING CARDS, MODULES OR INTERCONNECTING CABLES WHILE THIS UNIT IS ENERGIZED.

  • Page 25: 3: Special Application Dc Power Output Connection

    Relays Installation 2.2.3 Special Application DC Power Output Connection All Special Application DC power outputs are power-limited (refer to “UL Power-limited Wiring Requirements” on page 27). TB11, TB18 and TB13 offer 1.0 amps max, 24VDC nominal filtered power, programmable as resettable or non-resettable. PWR1 at TB11 can be wired/programmed as Class A or Class B power.

  • Page 26: 1: Class B Nac Wiring

    Installation Remote Synchronization Output 2.4.1 Class B NAC Wiring four Class B Notification Appliance Circuits, supervised and power-limited - 4.7 kΩ, ½ watt P/N:71252 UL listed NAC 3 NAC 1 NAC 4 NAC 2 Polarized Bells Polarized Bells Polarized Strobes Polarized Strobes Polarized Horns Polarized Horns...

  • Page 27: Ul Power-Limited Wiring Requirements

    UL Power-limited Wiring Requirements Installation Figure 2.9 Remote Sync Output Remote Power Supply Sync Input Remote Sync Output Optional Class A Return 4.7 KΩ ELR FACP main circuit board 2.6 UL Power-limited Wiring Requirements Power-limited and nonpower-limited circuit wiring must remain separated in the cabinet. All power-limited circuit wiring must remain at least 0.25”...

  • Page 28: Ipots-Com Communicator

    There are two configurable dip switches on the IPOTS-COM communicator. • SW3: 2-position DIP switch- Factory Settings- Do not change unless instructed to do so by Honeywell. • SW2: 6-position DIP switch- FUTURE USE- No configuration necessary. Remote Connection Feature Figure 2.13...

  • Page 29: Optional Module Installation

    Optional Module Installation Installation 2.8 Optional Module Installation WARNING: RISK OF ELECTRIC SHOCK AND EQUIPMENT DAMAGE DISCONNECT ALL SOURCES OF POWER (AC AND DC) BEFORE INSTALLING OR REMOVING ANY MODULES OR WIRING. 2.8.1 SLC-3LS Loop Expander Module Installation The SLC-3LS Card provides an additional SLC loop to the FACP. A maximum of 2 cards is allowed in the system, offering a total of 3 SLC loops.

  • Page 30: 3: Ann-Bus Annunciators/Modules

    Installation Optional Module Installation The following steps must be followed when installing the 4XTMF module: Remove all power (Primary and Secondary) from the FACP before installing 4XTMF. Carefully plug the connectors on the 4XTMF module into connectors J12 and J13 on the ES-1000X main circuit board, being careful not to bend any pins.
  • Page 31 Optional Module Installation Installation Exception: When using the ANN-RLY module, the installer must ensure that the maximum 24VDC power line drop does not exceed 0.3 volts. This results in the following wiring limitations: Wire Gauge Maximum Wire Length 312 feet 497 feet 787 feet 1,250 feet...

  • Page 32: Ann-Bus Device Addressing

    Installation Optional Module Installation  Powering Both ANN-BUS Circuits Simultaneously When simultaneously using the Primary and Secondary ANN-BUS circuits on the FACP, power can be shared from the non-resettable power output on TB11. Alternately, one ANN-BUS can be powered by the resettable power output (TB13 or TB18) once it is reconfigured as Non- resettable Power in panel programming.
  • Page 33 Optional Module Installation Installation  Installation Ensure that all power (AC and DC) has been removed from the FACP before installing the annunciator.  Opening/Closing Annunciator The following procedure details the steps used to open the annunciator in order to access the terminal block and DIP switches (refer to figure below): Turn the key switch to the ON (Unlocked) position by turning the key counter-clockwise.
  • Page 34 Installation Optional Module Installation  Wiring ANN-80 to FACP The following steps can be used as a guide to wire the annunciator. Make certain all power has been removed from the FACP prior to annun- ciator installation. Route wires from hole in backplate, through wiring channel and then to ANN-80 terminal block TB1 wiring channel wires Remove appropriate amount of wire insulation...

  • Page 35: Remote Fire Annunciator

    Optional Module Installation Installation  Trouble Response If the ANN-80 is installed but the ANN-BUS is not enabled at the FACP, the ANN-80 will indicate a trouble condition by NOT turning on its AC Power indicator. The LCD will also display Key Bus Trouble and the piezo will sound approximately once every 10 seconds. Note that the FACP will provide no indication of an ANN-80 trouble.
  • Page 36 Installation Optional Module Installation Select the address and configuration options for the ANN-S/PG module as described in the Programming section of this manual (refer to “ANN-BUS Setup” on page 87). Note that the Auto-configure feature allows the programmer to quickly bring all installed ANN-BUS modules online (refer to “Auto- Configure”...

  • Page 37: Ann-I/O Led Driver Module

    Optional Module Installation Installation Setting Printer Options Refer to the documentation supplied with the PRN-6F printer for instructions on using the printer menu controls. Set the printer options (under the menu area) as shown in the following table: Option Setting Option Setting Font...
  • Page 38 Installation Optional Module Installation  Specifications • Max. ANN-BUS Voltage: 24 VDC • Max. Current: Alarm: 200 mA Standby: 35 mA Each LED: 10 mA • Operating Temperature: 32°F to 120°F (0°C to 49°C) • Must be installed adjacent to the main FACP operator interface to meet UL 2017 standards •...

  • Page 39: Ann-Led Annunciator Module

    Optional Module Installation Installation Pin # LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Cathode LED9 LEDs LED10 LED Power Anode no connection Pin # LED11 LED12 LED13 LED14 LED15 LED16 LED17 LED18 Cathode LED19 LEDs LED20 Anode LED Power no connection Figure 2.22 ANN-I/O LED Wiring ANN-LED Annunciator Module...

  • Page 40: Ann-Rly Annunciator Module

    Installation Optional Module Installation  Mounting/Installation The ANN-LED Module is supplied with a metal backbox, mounting bracket, and cover. The ANN-LED must be mounted within 20’ (6.1m) of the FACP in the same room and wired in conduit. Refer to the ANN-LED Installation Document #53032 for more information. Figure 2.24 Exploded View of ANN-LED ...
  • Page 41 Optional Module Installation Installation  Mounting/Installation The ANN-RLY relay module can be mounted inside the ROME Series enclosure. Refer to the ROME Series Installation Document #53530 for mounting in the separate backbox. ROME Series Installation using ANN-MBRLY mounting bracket mounting holes ANN-RLY on mounting holes ANN-MBRLY...

  • Page 42: 4: Printer

    Installation Optional Module Installation 2.8.4 Printer A parallel printer may be connected to the FACP using the optional ANN-S/PG Serial/Parallel Interface Module. The printer can be used to provide a hard-copy printout of real-time events, history file and walktest data. Installation of the device requires panel programming to allow the FACP to communicate with the device.

  • Page 43: Section 3: Programming

    Section 3: Programming NOTICE TO USERS, INSTALLERS, AUTHORITIES HAVING JURISDICTION AND OTHER INVOLVED PARTIES This product incorporates field-programmable software. In order for the product to comply with the requirements in the Standard for Control Units and Accessories for Fire Alarm Systems, UL 864, certain programming features or options must be limited to specific values or not used at all as indicated below: Permitted in UL864/ Program feature or...

  • Page 44: User Programming

    Programming User Programming 3.1 User Programming The ES-1000X is completely field programmable and requires no special software skills. While programming the ES-1000X, the fire protec- tion capabilities of the control panel are enabled. Site-specific programming may be accomplished in any of the following ways: •...

  • Page 45: 1: Administrator Role

    Users and Passwords Programming 3.4.1 Administrator Role Password Change-Administrator The factory set password must be changed to clear the Password Fault from the panel. Pressing the Enter key on home screen will cause the following screen to be displayed: MAIN MENU 1=READ STATUS MODE 2=LOGIN Press 2 to login to the panel.

  • Page 46: Password Change- User

    Programming Users and Passwords A flashing cursor will appear in the center of the display. Enter the default password, 00000000. Then, enter a new, valid eight digit password in the second line. Once the last digit is entered, the following screen will be displayed: MODIFY ADMIN 1 VERIFY PASSWORD NEW:...

  • Page 47: Assign Role

    Users and Passwords Programming Select 1 to enable the User account. Each press of the 1 key will toggle the screen between Enabled Yes and Enabled No. Press 3 to assign a password. Note that if a user is disabled at any time, the password will need to be reassigned. MODIFY USER X ENTER PASSWORDS ADMIN X:...

  • Page 48: 2: User Role

    Programming Master Programming Level The following screen will appear when the password is entered: ADMIN X ACCOUNT 1=MODIFY ACCOUNTS 2=VIEW CYBER SEC LOG 3=NOT USED Select 1 to modify an account. MODIFY ACCOUNTS 1=ADMINISTRATORS 2=USERS 3=NOT USED Select 2 to modify a User account. MODIFY USER 1=USER 1 2=USER 2...

  • Page 49: 1=Autoprogram

    Master Programming Level Programming Select the appropriate User login ID: LOGIN FOR USER X ENTER PASSWORD Enter the User’s Master level password. Only a user with master level programming rights can access panel programming. The following screen will appear: MASTER MENU 1=PROGRAMMING MODE 2=FS-TOOL UP/DWNLOAD 3=USB UP/DOWNLOAD...

  • Page 50: 2=Point Program

    Programming Master Programming Level 3.5.2 Point Program The Point Program option allows the programmer to add a new addressable device to an SLC loop, delete an PROGRAMMING 1=AUTOPROGRAM existing device from the loop or change the programming for an existing device. Pressing 2, while viewing Pro- 2=POINT PROGRAM gramming Screen #1, will select the Point Program option and display the following screen: 3=ZONE SETUP...
  • Page 51 Master Programming Level Programming  Delete Detector Pressing 2 in the Detector Screen will display the Delete Detector Screen which allows the programmer to DETECTOR 1=ADD delete a specific detector: 2=DELETE DELETE DETECTOR 3=EDIT ENTER DETECTOR# Detector Screen Delete Detector Screen A flashing cursor will appear in the position of the first asterisk to the left.
  • Page 52 Programming Master Programming Level ZNNN - represents the first of five possible software zones that the detector is assigned to (NNN = the three digit zone number from 000 - 0255) V or * - indicates whether or not alarm verification is enabled (V = alarm verification enabled and * = alarm verification disabled) W or * - indicates whether or not walktest is enabled (W = walktest enabled and * = walktest disabled) X or * - indicates whether or not the detector is wireless (X = wireless detector and * = wired detector) 1D017 - represents the Loop, Device type and Device address (1=SLC Loop, D=Detector and 017=Detector Address 017)
  • Page 53 Master Programming Level Programming Fire/CO response is programmable (Alarm, Supv, or None) User-Defined-12 same as previous (Fire/CO) Photo/CO response is programmable (Alarm, Supv, or None) User-Defined-13 same as previous (Photo/CO) Photo Supervisory Supervisory, latching User-Defined-14 same as previous (Photo Supervisory) Det High Heat Fire Alarm User-Defined-15...
  • Page 54 Programming Master Programming Level For example, if a detector with address 005 is to be configured for Pre-Signal operation: Select Pre-signal Yes when editing the detector set to address 005 Program the desired zone or zones to be activated by this detector, in this example Z001 Program an output, such as a control module that is to be activated by detector 005 by assigning the same zone to it;...
  • Page 55 Master Programming Level Programming The Coding feature allows the programmer to select the type of output that the sounder base will generate when activated. Pressing 3 while viewing Sounder Base Screen #1 will cause the following displays to appear: CODING 1=STEADY 2=TEMPORAL 3 3=TEMPORAL 4...

  • Page 56: Module Programming

    Programming Master Programming Level Pressing 2 while viewing the Adjective/Noun Screen will cause the following screen(s) to be displayed. Note 1=STANDARD ADJECTIVE 2=STANDARD NOUN that the keypad down arrow key must be pressed to see all the Noun screens. Press the number corresponding to 3=CUSTOM ADJECTIVE the noun that is to be used as a descriptor for the location of the detector currently being programmed.
  • Page 57 Master Programming Level Programming When the last digit is keyed-in, the following screen will be displayed: ADD MODULE 1=CON 3=MON 2=CON:WL- 4=MON:WL RELAY Add Module Screen #2 Pressing 1 for Control Module, 2 for Wireless Relay Control Module, 3 for Monitor Module, or 4 for Wireless Monitor Module will cause the following screen to be displayed: ADD MODULE MODULE#...
  • Page 58 Programming Master Programming Level If the selected address has been added to programming and a module (such as a monitor module) with the selected address is physically installed on the SLC and is communicating with the control panel, the following screen will be displayed: Normal MONITOR <ADJ><NOUN>...
  • Page 59 Master Programming Level Programming Monitor module type selection will affect the function of the point as follows: Monitor Type Action When Activated Pull-Station Fire Alarm User-Defined-1 same as previous (Pull-Station) Waterflow Fire Alarm Delayed User-Defined-2 same as previous (Waterflow) Monitor Fire Alarm User-Defined-3 same as previous (Monitor)
  • Page 60 Programming Master Programming Level Pre-signal EDIT MONITOR 1=PRE-SIGNAL To enable the Pre-signal feature, press 1 while viewing Edit Monitor Screen #3 until the display reads Pre-sig- WIRELESS nal Yes. Each press of the 1 key will cause the display to toggle between Pre-signal Yes and Pre-signal No. Edit Monitor Screen #3 Refer to“Pre-signal”...
  • Page 61 Master Programming Level Programming Pressing 2 while viewing the Adjective/Noun Screen will cause the following screen(s) to be displayed. Note 1=STANDARD ADJECTIVE 2=STANDARD NOUN that the keypad down arrow key must be pressed to see all the Noun screens. Press the number corresponding to 3=CUSTOM ADJECTIVE the noun that is to be used as a descriptor for the location of the monitor module currently being programmed.
  • Page 62 Programming Master Programming Level W or * - represents Waterflow Timer Delay (W = Waterflow Timer Delay enabled, * = Waterflow Timer Delay disabled) ZNNN - represents the first of five possible software zones that the module is assigned to (NNN = the three digit zone number from 000 - 255) 1M002 - represents the Loop, Device type and Device address (1 = SLC Loop, M=Module and 002 = Module Address 02) To change the programming for the displayed module, press the keypad down arrow key to view the following Edit Control screens:...
  • Page 63 Master Programming Level Programming The following table contains control module type codes and their functions which are displayed in the Control Type screens: Control Type Special Function Bell Circuit NAC Type - supervised Horn Circuit NAC Type - supervised Sounder NAC Type - supervised Relay-1FC Ignore Open Circuit...
  • Page 64 Programming Master Programming Level Pressing 1 while viewing the Adjective/Noun Screen will cause the following screen(s) to be displayed. Note 1=STANDARD ADJECTIVE 2=STANDARD NOUN that the keypad down arrow key must be pressed to see all the Adjective screens. Press the number correspond- 3=CUSTOM ADJECTIVE ing to the adjective that is to be used as a descriptor for the location of the control module currently being pro- 4=CUSTOM NOUN...

  • Page 65: 3=Zone Setup

    Master Programming Level Programming 3.5.3 Zone Setup Pressing 3 while viewing Programming Screen #2 will access the Zone Setup screens as illustrated below: PROGRAMMING 1=AUTOPROGRAM ZONE SETUP ZONE SETUP ZONE SETUP 2=POINT PROGRAM 3=ZONE SETUP 1=ZONE TYPES 1=ZONES INSTALLED 1=ZONES AVAILABLE Programming Screen #2 2=ZONE MESSAGE 2=ZONES ENABLED...

  • Page 66: Zones Installed

    Programming Master Programming Level Pressing 1 will cause the display to change to PAS 253 On. Each press of the 1 key will cause the display to toggle between PAS 253 On and PAS 253 Off. When Zone 253 is programmed On, a PAS (Positive Alarm Sequence) activation of any smoke detector will cause Zone 253 to activate.

  • Page 67: Zones Available

    Master Programming Level Programming Zones Available Pressing 2 while viewing Zone Setup Screen #3 will display the following screen: ZONE SETUP 1=ZONES AVAILABLE ZONES AVAILABLE 001 002 003 004 005 Zone Setup Screen #3 006 007 008 009 010 011 012 013 014 015 The display will show all of the zones that are still available for programming.

  • Page 68: Function Keys

    Programming Master Programming Level • Function Keys: This feature allows the user to rapidly enable/disable various fire panel inputs and outputs during scheduled maintenance. • Banner: This option allows the user to change the top two lines of the LCD display from the blank factory default readout to a user defined readout when the control panel is in Normal condition.

  • Page 69: Banner

    Master Programming Level Programming  NACs Each function key can be assigned to control any of the 4 onboard NAC circuits on the ES-1000X. By pressing the 2 key while viewing the Function Keys Screen #2 the following screen displays, allowing the user to select the desired NAC circuit(s). F(X) NACS 1=NAC 1 3=NAC 3...
  • Page 70 Programming Master Programming Level  Time To change the time, press 1 while viewing the Time-Date Screen. The following screen will be displayed: ENTER TIME 10:00 AM 1=AM 2=PM Time Screen A flashing cursor is located toward the top left of the display. Below the cursor is the current time. To change the time, enter the two-digit hours followed by the two-digit minutes.

  • Page 71: Timers

    Master Programming Level Programming Timers Timer delays for PAS, Pre-signal and waterflow activation can be programmed by pressing 1 while viewing SYSTEM SETUP 1=TIMERS System Setup Screen #2. The following screen will be displayed: 2=NAC 3=RELAYS TIMERS TIMERS 1=PAS DELAY 1=AC LOSS DELAY System Setup Screen #2 2=PRE SIGNAL...
  • Page 72 Programming Master Programming Level Pressing 2 while viewing AC Loss Delay Screen #1 will display the following: AC LOSS DELAY RANGE 00-23 HOURS AC Loss Delay Screen #2 A flashing cursor will appear in the lower left corner of the display. Type the two digit AC loss reporting delay in hours (00 to 23 hour delay). When the second digit is entered, the display will return to AC Loss Delay Screen #1.

  • Page 73: Nacs (Notification Appliance Circuits)

    Master Programming Level Programming  Suite Resound (Canadian Mode Only) The Suite Resound feature is only available when the FACP is in Canadian mode of operation. When enabled, TIMER 1=IN SUITE SIL. this feature will resound all outputs and NACs that were silenced by the In Suite Silence timer (if there is an 2=SUITE RESOUND unacknowledged fire alarm on the panel) after a programmed length of time.
  • Page 74 Programming Master Programming Level  Silenceable Pressing 3 while viewing NAC Screen #1 will cause the display to change to Silenceable No. This will prevent the selected main circuit board NAC from being silenced by pressing the Alarm Silence key or by the Auto Silence feature. Each press of the 3 key will cause the dis- play to toggle between Silenceable Yes and Silenceable No.
  • Page 75 Master Programming Level Programming Any NACs currently in 1st stage activation will remain in 1st stage. Pressing the Acknowledge switch does not affect NACs already in 2nd stage activation. If an F3 button in pressed, the NACs will progress to the second stage. If another alarm point is activated and the countdown timer is counting, the alarm point will have no effect on the NACs unless the alarm point’s zones are directly mapped to one of the NACs, in which case it will follow the procedure outlined in step 2.

  • Page 76: Relays

    Programming Master Programming Level Relays Pressing 3 while viewing System Setup Screen #2 will allow the programmer to configure two main circuit SYSTEM SETUP 1=TIMERS board Form-C relays from the following screen: 2=NAC RELAYS 3=RELAYS 1=RELAY 1 System Setup Screen #2 2=RELAY 2 3=RELAY 3 Relays Selection Screen...

  • Page 77: Waterflow Silenceable

    Master Programming Level Programming • Addressable ionization smoke detector sensitivity is automatically monitored using Canadian specifications. • The Positive Alarm Sequence and Pre-Signal option are not available for Canadian applications. • The F1 function key is automatically configured to perform a manual alarm signal activation when pressed. •...

  • Page 78: Charger Enable

    Programming Master Programming Level Charger Enable When using an external battery charger, the FACP battery charger must first be disabled. Pressing 1 while view- SYSTEM SETUP 1=CHARGER ENAB ing System Setup Screen #5 will cause the display to toggle to Charger Enab No, which will allow the use of an 2=BAT SIZE 18-26 external battery charger.

  • Page 79: 7: Communicator

    Master Programming Level Programming 3.5.7 Communicator The communicator settings allow the user to configure the settings for the optional IPOTS-COM and CELL- PROGRAMMING 1=HISTORY MOD/CELL-CAB-FL if installed in the system. Pressing 2 while viewing the Programming Screen #3 will 2=COMMUNICATOR cause the following Communicator options to be displayed: 3=ANNUNCIATORS Programming Screen #3...

  • Page 80: Ip Settings

    Programming Master Programming Level  Gains The Gains value is the telephone’s transmitting “volume control”. To adjust the settings, press 3 while viewing POTS SETTINGS 1=LINE 1 the POTS Settings screen. The following screen will be displayed: 2=LINE 2 GAINS 3=GAINS 1=DIALING NORM...

  • Page 81: Primary And Secondary Communication Paths

    Master Programming Level Programming  Ethernet Fault The Ethernet Fault Time is the duration of the communication loss between the FACP and the ethernet infra- IP SETTINGS 1=ETHERNET FAULT structure. MAC CRC C3F0 Pressing 1 on the IP Settings Screen #2 will display the following: IP Settings Screen #2 ETHERNET FAULT TIME RANGE 1-60 MINUTES...
  • Page 82 Programming Master Programming Level The Phone Number screen is used to enter the Central Station phone number that the Communicator will be contacting. A maximum of 20 characters can be entered with valid entries being 0 - 9 and A - C where A = *, B = # and C = 2 seconds pause. A flashing cursor will appear in the lower left corner of the screen.

  • Page 83: Trouble Report Limit (Dialer Runaway Prevention)

    Master Programming Level Programming Supervision Settings Pressing 1 while viewing Ethernet Options Screen #2 will cause the display to toggle between the 4 supervision ETHERNET OPTIONS 1=SUPV. SETTINGS setting options. Toggle to select NFPA 2010 Sole Path, NFPA 2010 Dual Path, NFPA 2013 Sole Path, or NFPA NFPA 2013 DUAL PATH 2013 Dual Path.
  • Page 84 Programming Master Programming Level The tables on the following pages list all of the Events and their default Event Codes for the various Communication Formats. The information shown in Table 3.3 is automatically programmed for the Central Station phone number Event Codes when the Ademco Contact ID or SIA Format is selected.
  • Page 85 Master Programming Level Programming MON-USER-DEF-12 Zone Point MON SUPERV AUTO Zone Point MON-USER-DEF-13 Zone Point HVAC OVRRIDE Zone Point POWER MON Zone Point MON-USER-DEF-14 Zone Point TROUBLE MON POINT_FAULT code will always be transmitted MON-USER-DEF-15 POINT_FAULT code will always be transmitted PROCESS MON Zone Point...

  • Page 86: 8: Annunciators

    Programming Master Programming Level CCP UPDATE FAULT ETHERNET FAULT PRINTER FAULT NAC 1 FAULT NAC 2 FAULT NAC 3 FAULT NAC 4 FAULT 24 VDC FAULT VOICE EVAC FAULT ACS FAULT LCD-80F FAULT PRI ANN-BUS FAULT SEC ANN-BUS FAULT PRI ANN CLASS A REMOTE SYNC DIS NAC 1 DISABLE NAC 2 DISABLE...

  • Page 87: Ann-Bus Setup

    Master Programming Level Programming ANN-BUS Setup Two ANN-BUS circuits are available on the ES-1000X. Press 1 to configure the Primary ANN-BUS or press 2 ANN-BUS SELECT 1=PRIMARY to configure the Secondary ANN-BUS. The following screens will be displayed for either ANN-BUS circuit 2=SECONDARY where (XXX) indicates either Primary or Secondary..
  • Page 88 Programming Master Programming Level ANN-I/O Options Pressing 2 for Module Options while viewing ANN-BUS Address screen when the ANN-I/O option is selected will display the following screen: ANN-I/O - ADDR X-1 ANN-I/O - ADDR X-1 ANN-I/O - ADDR X-1 1=RANGE PT001-030 1=POINT/ZONE POINT...
  • Page 89 Master Programming Level Programming Zone 021 Zone 061 Zone 101 Zone 141 Zone 181 Zone 221 Not Used Zone 022 Zone 062 Zone 102 Zone 142 Zone 182 Zone 222 Not Used Zone 023 Zone 063 Zone 103 Zone 143 Zone 183 Zone 223 Not Used...
  • Page 90 Programming Master Programming Level Point 026 Point 066 Point 106 Point 146 Not Used Point 027 Point 067 Point 107 Point 147 Not Used Point 028 Point 068 Point 108 Point 148 Not Used Point 029 Point 069 Point 109 Point 149 Not Used Point 300...
  • Page 91 Master Programming Level Programming Zone 050 Zone 051 Zone 052 Zone 053 Zone 054 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Zone 055 Zone 056 Zone 057 Zone 058 Zone 059 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Table 3.5 ANN-RLED Module #2 The LED assignments for the modules annunciating Zone Ranges 060-089, 090-119, 120-149, 150-179, 180-209, 210-239, and 240-255 will follow the same pattern as the second ANN-RLED module.
  • Page 92 Programming Master Programming Level Point 011 Point 012 Point 013 Point 014 Point 015 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Point 016 Point 017 Point 018 Point 019 Point 020 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Point 021 Point 022 Point 023 Point 024 Point 025 Active/Alarm...
  • Page 93 Master Programming Level Programming Point 016 Point 017 Point 018 Point 019 Point 020 Active/Alarm Active/Alarm Active/Alarm Active/Alarm Active/Alarm Point 016 Point 017 Point 018 Point 019 Point 020 Trouble Trouble Trouble Trouble Trouble Point 016 Point 017 Point 018 Point 019 Point 020 Supervisory...

  • Page 94: Ann-Bus Options

    Programming Master Programming Level ANN-BUS Options Three ANN-BUS modules have more programming options. Pressing 3 while viewing the Annunciators screen ANN-BUS SELECT 1=PRIMARY will display the following. 2=SECONDARY 3=ANN-BUS OPTIONS ANN-BUS Annunciator Screen 1=ANN-S/PG OPTIONS 2=ANN-LED OPTIONS 3=ANN-80/100 OPTIONS ANN-BUS Options Screen ...

  • Page 95: 9: Password Change

    Master Programming Level Programming  ANN-80/100 Options Pressing 3 while viewing the ANN-BUS screen will display the following screen: XXX ANN-BUS 1=ANN-S/PG OPTIONS ANN-80/100 OPTIONS ANN-80/100 OPTIONS 2=ANN-LED OPTIONS 1=SIL BTN ENABLE YES 3=ANN-80/100 OPTIONS 1=PIEZO ENABLE 2=RST BTN ENABLE YES 2=LOCK ENABLE ANN-BUS Options Screen 3=DRL BTN ENABLE YES...

  • Page 96: Invalid Password

    Programming Master Programming Level Invalid Password If a password is entered incorrectly or is not a valid password, the panel will display either of the following messages. MODIFY USER X MODIFY USER X NEW PASSWORD CANNOT USER X PASSWORD BE ALL THE SAME CHAR IS INCORRECT PRESS ENTER OR ESC PRESS ENTER OR ESC...

  • Page 97: Maintenance Programming Level

    Maintenance Programming Level Programming Pressing 2 while viewing the Program Check Screen #1 will display a screen similar to the following: ZONES NO INPUT 005 007 009 010 011 1M001 The Zone No Input screen allows the programmer to view the zones which have not been programmed to at least one input device (not including general alarm Zone 00).

  • Page 98: 1: Disable Point

    Programming Maintenance Programming Level 3.6.1 Disable Point Pressing 1 for Point Program, while viewing Maintenance Screen #1 will cause the following screens to be dis- PROGRAMMING played: 1=POINT PROGRAM 2=HISTORY 3=PROGRAM CHECK POINT PROGRAM, LOOP: 1=LOOP 1 Maintenance Screen #1 2=LOOP 2 3=LOOP 3 Device Select Screen...

  • Page 99: 3=Program Check

    Maintenance Programming Level Programming Pressing 1 while viewing the Erase History Screen will cause the message ERASING HISTORY, PLEASE WAIT to be displayed. The display will then return to the History Screen. Pressing 2 will cause the display to return to the History Screen without erasing the History file. 3.6.3 Program Check Pressing 3 while viewing Maintenance Screen #1 will cause the following screen to be displayed: PROGRAMMING...

  • Page 100: 5: System

    Programming Maintenance Programming Level Pressing 1 for View Walktest Log while viewing the Unit In Walktest screen will cause a screen similar to one of the following two screens to be displayed: ALARM: MONITOR NO EVENTS IN NORTH CLASSROOM WALKTEST LOG Z001 10 15A 050417 1M006 If there are no events in the current walktest session, the first screen will be displayed, indicating no events have been stored in the walktest...

  • Page 101: 6: Zone Setup

    Maintenance Programming Level Programming A flashing cursor will appear on the left side of the display. Enter the four digit number corresponding to the time (0000 - 1259). When the fourth digit is entered, the cursor will move one position to the right. Press 1 for AM or 2 for PM to complete entering the time. The display will return to the Time and Date Screen displaying the new time.

  • Page 102: Section 4: Operating Instructions

    Section 4: Operating Instructions 4.1 Panel Control Buttons 4.1.1 Acknowledge The first press of the Acknowledge key silences the piezo sounder, changes flashing LEDs to steady, and also changes the status field on the LCD display from capital letters to small letters. When the piezo is silenced, an acknowledge message is sent to the printer and the history file.

  • Page 103: Normal Operation

    Normal Operation Operating Instructions Disabled This is a yellow LED that flashes to indicate that a zone, NAC, detector or module has been temporarily disabled in programming by the user. Communication This is a yellow LED that flashes to indicate a communication fault, including loss of phone lines, communication failure with either Central Station, or total communication failure.

  • Page 104: Alarm Operation

    Operating Instructions Alarm Operation <NOUN>; refers to the user programmed noun descriptor from library list resident in the control panel or custom entry via PC. • Third line in display: INVREP indicates an invalid reply from the addressable device. Other possible troubles include: –...

  • Page 105: Co Alarm Operation

    CO Alarm Operation Operating Instructions • Third line in display: Z000 indicates the zone programmed to this device which, in this example, is general alarm Zone 000. Note that a single device can be programmed to five different zones but only the first zone will be displayed. •...

  • Page 106: Process Monitor Operation

    Operating Instructions Process Monitor Operation A typical Supervisory event would be displayed as illustrated in the following: ACTIVE SUPERVISORY <ADJ> <NOUN> Z000 06:21A 121822 1M001 Note that, like alarms, supervisory signals latch (except when programmed for supervisory autoresettable) and can be assigned to software zones.

  • Page 107: Nac Operation

    NAC Operation Operating Instructions • Activate appropriate LED on the ANN-LED annunciator (required for this application) • Each ANN-LED can support up to 10 zones. Medical alert conditions latch. They can be assigned to software zones. 4.11 NAC Operation There are four programmable NACs (Notification Appliance Circuits) resident on the ES-1000X main circuit board. All NACs may be pro- grammed as silenceable or nonsilenceable and may also be programmed for steady or coded operation.

  • Page 108: Coded Operation

    Operating Instructions Coded Operation 4.18 Coded Operation The NAC circuits resident on the control panel main circuit board can be programmed for coded operation. The available pulse rates which can be programmed for coded operation are as follows: • Continuous: Steady output with no pulsing •...

  • Page 109: 2: Autosilence Timer

    Walktest Operating Instructions 4.21.2 Autosilence Timer If Autosilence is selected, the notification appliances, programmed as silenceable, will automatically be silenced after a programmable dura- tion of 5 to 30 minutes. Pressing the Drill key will restart the timer. Autosilence operation requires the approval of the local Authority Hav- ing Jurisdiction.

  • Page 110: Read Status

    Operating Instructions Read Status If the MMF-302 monitor module is used for a supervised, 2-wire smoke zone, alarming any monitor module in the system will result in the activation of programmed control outputs for an additional eight seconds or less. This is caused by the temporary removal of 24 VDC resettable power from the MMF-302.

  • Page 111: 2=Zones

    Read Status Operating Instructions Entering the three digit detector address will cause the control panel to display the current status of the selected device. For example, if a detector with address 001 on the SLC loop is entered, a display similar to the following will appear: NORMAL SMOKE(PHOTO) NORTH CLASSROOM Z005...

  • Page 112: 4: Timers

    Operating Instructions Read Status 4.23.4 Timers Pressing 2 while viewing Read Status Screen #2 will cause the following Timer screens to be displayed: TIMERS TIMERS PAS DELAY AC LOSS DELAY PRE SIGNAL CTRL MOD DLY WATERFLOW These screens will indicate the delay time, in seconds, for each of the first three and last possible delay options. The AC Loss Delay time is displayed in hours.

  • Page 113: 8: History

    Read Status Operating Instructions 4.23.8 History Pressing 3 while viewing Read Status Screen #3 will display the following screen: HISTORY 1=VIEW ALL 2=VIEW ALARMS 3=VIEW OTHER EVENTS The operator can view all events which have been stored in the history file, only alarms or other events, such as troubles or supervisories, by pressing the corresponding number key.

  • Page 114: 11: Print

    Operating Instructions Read Status Pressing 2 for POTS Settings while viewing Communicator Screen #1 will display settings for the telephone portion of the Communicator. POTS SETTINGS 1=LINE 1 2=LINE 2 3=GAINS Pressing 1 or 2 will display whether each phone line is enabled Yes or disabled No, whether the phone type is touchtone or rotary, and whether the phone line is being supervised Yes or No.

  • Page 115: Chamber Value

    Read Status Operating Instructions Pressing 3 while viewing Print Screen #1 allows the user to print the Walktest summary which will list the total of each type of input activa- tion. Pressing 1 while viewing Print Screen #2 allows the user to print the detector data for each addressable smoke detector connected to the sys- tem.

  • Page 116: 12: Time/Date

    Operating Instructions Read Status Figure 4.1 illustrates a graphic representation of the maintenance levels: DIRTY Maintenance Urgent Maintenance Alert Acceptable Range Low Chamber Reading VALUE Figure 4.1 Diagram of Maintenance Levels Pressing 2 while viewing Print Screen #2 allows the user to print the Communicator’s settings. Refer to “Com- PRINT municator”...

  • Page 117: Section 5: Central Station Communications - Pots Transmission

    Section 5: Central Station Communications - POTS Transmission The control panel transmits zone and system status reports to Central Stations via the public switched telephone network. Two supervised telephone line connections are made to interface the control panel to the telephone lines. Two optional 7 foot telephone cords are available for this purpose and can be purchased separately.
  • Page 118 Central Station Communications - POTS Transmission Transmittal Priorities Red LEDs are provided on the circuit board to identify which telephone line is activated. Also, a green LED labeled Kissoff will turn on whenever the control panel has successfully transmitted reports to the Central Station. The Kissoff LED may turn on several times during communications with a Central Station.

  • Page 119: Section 6: Fs-Tools Upload/Download

    Section 6: FS-Tools Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download via the FS-Tools programming util- ity. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. The control panel may be programmed or interrogated off-site via the public switched telephone network or locally using a USB cable.

  • Page 120: Transferring A Program

    FS-Tools Upload/Download Transferring a Program While this screen is displayed, programming uploads are allowed. Exiting this screen will disable any further downloads to the FACP. Also, following 30 minutes of inactivity (including up/downloading), the Accept Download screen will time-out, causing the display to return to the System Normal screen.

  • Page 121: Section 7: Usb Upload/Download

    Section 7: USB Upload/Download Important! The FACP will automatically reset 2 minutes after completion of a user program download. To prevent program corruption, the operator must wait until this panel reset occurs before performing any panel operations. CAUTION: After successfully downloading a program, make certain to perform the following steps: Print out all programmed data via Print Mode or manually view programmed entries and compare to intended program data Test all affected panel operations Immediately correct any problems found...
  • Page 122 USB Upload/Download USB Upload/Download The following screen will be displayed while the program is sent to the USB drive: USB UP/DOWNLOAD SYSTEM CONFIGURATION TRANSFER IN PROCESS PLEASE WAIT An error message will display if there is no USB drive inserted in the FACP or if there is an existing configuration saved on the drive with the same file name.

  • Page 123: Section 8: Firmware Upgrade

    Section 8: Firmware Upgrade In order to supply the latest features and functionality in fire alarm and life safety technology to our customers, we make frequent upgrades to the embedded software in our products. To ensure that you are installing and programming the latest features, we strongly recommend that you download the most current version of software for each product from www.firelite.com prior to commissioning any system.
  • Page 124 Firmware Upgrade Firmware Upgrade If the following error message displays, ensure the flash drive is inserted at J20 and it is fully seated. FIRMWARE UPDATE NO USB CONNECITON ESC TO EXIT OR ENTER AFTER DEV CONNECTED The following error message will display if the upgrade file is not found on the flash drive. Ensure the file is present and retry. FIRMARE UPDATE FILE NOT FOUND ES-1000X Series Manual —...

  • Page 125: Section 9: Power Supply Calculations

    Section 9: Power Supply Calculations 9.1 Overview This section contains instructions and tables for calculating power supply currents in alarm and standby conditions. This is a four-step pro- cess, consisting of the following: Calculating the total amount of AC branch circuit current required to operate the system Calculating the worst-case system current load on the control panel, when primary (AC) power is applied, to assure that the limit of the its internal power supply will not be exceeded.
  • Page 126 Power Supply Calculations Calculating the System Current Load Calculation Column 1 Calculation Column 2 Calculation Column 3 Device Type Primary (AC) Power Source Secondary (Battery) Power Source Secondary (Battery) Power Source Fire Alarm Current (amps) Fire Alarm Current (amps) Standby Current (amps) X [current draw]= Total X [current draw]=...

  • Page 127: Calculating The Battery Size

    Calculating the Battery Size Power Supply Calculations Refer to the Device Compatibility Document for standby current. Must use compatible listed Power Supervision Relay. Maximum alarm current for each sounder base is 0.015 amps which must be supplied by aux. 24VDC source. When powered by an external source, use 0.040A.

  • Page 128: Appendix A: Software Zones

    Appendix A: Software Zones A.1 Correlations Setup and configuration of an addressable system is different than a conventional system. In a conventional system, assignment of input devices (smoke detectors, pull stations, heat detectors, etc.) to zones is accomplished through wiring. The wiring is direct from clearly marked panel terminals to any device assigned to a particular zone.
  • Page 129 Correlations Software Zones Correlation of Input and Output Zones Input Devices Zones Output Devices smoke control smoke control ZONE monitor control monitor control control monitor control smoke ZONE control smoke smoke control smoke ZONE smoke control monitor ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 130 Software Zones Correlations The zone correlations which are shown graphically above are also presented in Table A.1 on page 130 and Table A.2 on page 131. DETECTOR ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number smoke FIRST HALL...
  • Page 131 Correlations Software Zones MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number monitor monitor 1, 2 monitor 1, 2 monitor control control control control control 1, 2, 3 control Table A.2 Module Programming Sheet Example ES-1000X Series Manual —...
  • Page 132 Software Zones Correlations DETECTOR ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.3 Blank Detector Programming Sheet - 1 of 2 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 133 Correlations Software Zones DETECTOR ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.3 Blank Detector Programming Sheet - 2 of 2 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 134 Software Zones Correlations MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.4 Blank Module Programming Sheet - 1 of 2 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 135 Correlations Software Zones MONITOR/CONTROL MODULE ZONE ASSIGNMENT Device Zone Device Zone Address ADJ/NOUN Address ADJ/NOUN Type Number Type Number Table A.4 Blank Module Programming Sheet - 2 of 2 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...

  • Page 136: Appendix B: Default Programming

    Appendix B: Default Programming The following table provides a list of the programming options and their factory default settings. Program Option Factory Default Program Option Factory Default Detector Programming Not Installed Battery Size 12-30AH Detector Type Smoke-Photo Language English Detector Verification Aux Power 1 Class A Detector Walktest Aux Power 1 Resettable...

  • Page 137: Appendix C: Nfpa Standard-Specific Requirements

    Appendix C: NFPA Standard-Specific Requirements The ES-1000X has been designed for use in commercial, industrial, and institutional applications and meets the requirements for service under the National Fire Protection Association (NFPA) Standards outlined in this Appendix. The minimum system components required for compliance with the appropriate NFPA standard are listed below: ES-1000X Control Panel Contains the main control board, cabinet (backbox and door), main power supply transformer and power supply.
  • Page 138 NFPA Standard-Specific Requirements NFPA 72 Remote Station Protective Signaling System Notes: Enable 4XTMF supervision in FACP System Setup programming. Refer to page 77 for more information. Refer to “4XTMF Transmitter Module Installation” on page 29 for detailed information. RS82 Remote Station Receiver UL listed. Refer to Instruction Manual for Remote Station Receiver Model RS82.
  • Page 139 NFPA Standard-Specific Requirements NFPA 72 Proprietary Protective Signaling Systems ES-1000X Addressable Fire Control Panel ES-1000X Main Board Form-C Alarm contact programmed to activate on General Alarm. Form-C Trouble contact which will automatically activate on any Trouble condition. Form-C relay contact programmed to activate on Supervisory condition.

  • Page 140: C.1: Mbt-1 Municipal Box Trip - Silenceable

    NFPA Standard-Specific Requirements MBT-1 Municipal Box Trip - Silenceable C.1 MBT-1 Municipal Box Trip - Silenceable The following figure illustrates the connection of the MBT-1 (Municipal Box Trip) between the FACP and a Local Energy Municipal Box. The use of an addressable control module programmed for General Alarm and Silenceable allows silencing of the Municipal Box without resetting the panel or box.

  • Page 141: Appendix D: Wire Requirements

    Appendix D: Wire Requirements T-tapping of the SLC loop wiring is allowed for 2-wire (Class B) configurations. The total resistance of any branch cannot exceed 50 ohms. The total wire length of all branches cannot exceed 10,000 feet (3,000 m). Connecting external system accessories to the ES-1000X main circuits must be carefully considered to ensure proper operation.

  • Page 142: D.1: Nac Wiring

    Wire Requirements NAC Wiring D.1 NAC Wiring The following table lists NAC wiring requirements for the FACP. CLASS-B CLASS-A Max. Max. allowable wire pair length Max. allowable wire pair length allowable NAC Load (feet) (feet) total loop (Amps) resistance AWG 12 AWG 14 AWG 16 AWG 18...

  • Page 143: Appendix E: Hvac Control

    Appendix E: HVAC Control The FACP can be programmed to shut down a building’s HVAC fans in the event of a fire. The fans cannot be restarted until the fire alarm condition has been cleared and the FACP has been reset to a normal (non-alarm) condition. IMPORTANT! This HVAC feature is not to be used for smoke control.

  • Page 144: E.2: Monitor Module Operation

    HVAC Control Monitor Module Operation E.2 Monitor Module Operation E.2.1 HVAC RESTART The HVAC RESTART type code can be assigned to any addressable monitor module for the purpose of resetting (deactivating) the HVAC SHUTDN control module and turning the fans back on. The HVAC RESTART monitor module acts globally throughout the FACP system and therefore is not programmed to a particular software zone.

  • Page 145: Appendix F: Ademco Contact Id Format Event Code Descriptions

    Appendix F: Ademco Contact ID Format Event Code Descriptions This appendix describes the various Event Codes and their messages which are available for the Ademco Contact ID Format. F.1 Transmission Format Between DACT and Receiver The transmission string for the Ademco Contact ID Format is as follows: SSSS 18 QXYZ GG CCC where SSSS=...
  • Page 146 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE Medical Alarms - 100 100 Medical EMERG - Personal Emergency - # 101 Pendant Transmitter EMERG - Personal Emergency - # 102 Fail to report in EMERG - Fail to Check-in - # Fire Alarms - 110 110 Fire Alarm...
  • Page 147 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE 156 Day trouble ALARM - Day Zone - # 157 Low bottled gas level ALARM - Low Gas Level - # 158 High Temp ALARM - High Temperature - # 159 Low Temp ALARM - Low Temperature - # 161 Loss of air flow...
  • Page 148 Ademco Contact ID Format Event Code Descriptions Ademco Contact ID Typical Printout EVENT MESSAGE Communication Troubles - 350 and 360 350 Communication TROUBLE - Communication Trouble 351 Telco 1 fault TROUBLE - Phone Line #1 352 Telco 2 fault TROUBLE - Phone Line #2 353 Long range radio transmitter fault TROUBLE - Radio Transmitter 354 Fail to communicate...
  • Page 149 Ademco Contact ID Typical Printout Ademco Contact ID Format Event Code Descriptions EVENT MESSAGE Sounder/Relay Disables - 520 520 Sounder/Relay disable DISABLE - Sounder/Relay - # 521 Bell 1 disable DISABLE - Bell/Siren - #1 522 Bell 2 disable DISABLE - Bell/Siren - #2 523 Alarm relay disable DISABLE - Alarm Relay 524 Trouble relay disable...

  • Page 150: Appendix G: Central Station Points

    Appendix G: Central Station Points The IPOTS-COM transmits Central Station Reports in a numerical format which indicates the FACP addressable device address that is reporting and the SLC loop on which it resides. The following table indicates the Central Station Report (CS Report) number that will be transmitted and the addressable device address and SLC loop number it represents.
  • Page 151 Central Station Points Module Module Module Module Module Address Address Address Address Address Report Report Report Report Report Loop 1 Loop 1 Loop1 Loop 1 Loop 1 Table G.2 Addressable MODULES on SLC Loop 1 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 152 Central Station Points Detector Detector Detector Detector Detector Address Address Address Address Address Report Report Report Report Report Loop 2 Loop 2 Loop2 Loop 2 Loop 2 Table G.3 Addressable DETECTORS on SLC Loop 2 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 153 Central Station Points Modules Modules Modules Modules Modules Address Address Address Address Address Report Report Report Report Report Loop 2 Loop 2 Loop2 Loop 2 Loop 2 Table G.4 Addressable MODULES on SLC Loop 2 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 154 Central Station Points Detectors Detectors Detectors Detectors Detectors Address Address Address Address Address Report Report Report Report Report Loop 2 Loop 2 Loop2 Loop 2 Loop 2 Table G.5 Addressable DETECTORS on SLC Loop 3 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 155 Central Station Points Modules Modules Modules Modules Modules Address Address Address Address Address Report Report Report Report Report Loop 2 Loop 2 Loop2 Loop 2 Loop 2 Table G.6 Addressable MODULES on SLC Loop 3 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...

  • Page 156: Appendix H: Nfpa Requirements

    Appendix H: NFPA Requirements The following is the minimum configuration to meet the NFPA requirements. Non- Remote Central Module Description Local Proprietary Emergency Station Station Signaling ES-1000X Control Unit IPOTS-COM Telco/IP Reporting 4XTMF RP/municipal box transmitter BB-55F Battery box ANN-LED Annunciator module ANN-80 Remote annunciator...

  • Page 157: Appendix I: Open/Short/Ground Trip Values

    Appendix I: Open/Short/Ground Trip Values Table I.1 lists the earth fault resistance detection for each applicable terminal on the FACP. Output Circuit Terminal Trip Resistance (in ohms) Remote Sync 203K Remote Sync 176K NAC 1-4 203K NAC 1-4 176K ANN Bus 138K ANN Bus 143K...

  • Page 158: Appendix J: Canadian Applications

    TB11) in metal conduit ANN-LED (adjacent to FACP) ANN-LED FACP ANN-100 ANN-I/O FIRE SYSTEM SYSTEM ACTIVE CALL CONTROL ANN-S/PG ® by Honeywell optional ANN-RLY ECC-50/100 audio system Figure J.1 FACP Minimum Configuration - Single ANN-LED ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...
  • Page 159 Canadian Applications Notes: 1. The CRF-300 and the MMF-300 must be mapped to the same zone which is programmed for supervisory operation. 2. No other device can be mapped to that MMF-300* supervisory zone. 3. Wire gauge must be 18AWG minimum. SLC Loop Output on SLC-3LS...

  • Page 160: Index

    Index Numerics ANN-SB80KIT Mounting Kit 33 clock format 70 annunciator guidelines 18 coded operation 108 24 Hour Test Time 82 annunciator module 13 coding 24VDC power 68 annunciators 18 NAC 74 4XTMF module 137 asterisk 44 two stage operation 74 coil resistance 29 automatic test operation 107 communication format 82...
  • Page 161 Index device IP address 80 ANN-BUS annunciators 18 module dimensions add 56 cabinet 22 addressing 16 DIRTY1 115 delete 57 hazard condition 106 DIRTY2 115 edit monitor 57 history 78 disable programming 56 erase 78 battery charger 68 see also addressable modules 16 maintenance level 98 charger 68 monitor module 16...
  • Page 162 Index printer enable 100 configuration 42 remote sync enable 68 operating instructions 102 connection 36 remote sync output 14 operation setup 42 alarm 104 printer module 13 see also ringer equivalence number 19 CO alarm 105 printer options 36 reset 15 disable/enable 107 process monitor 106 resettable power 13...
  • Page 163 Index voltage 14 synchronization 26 walktest 12 by manufacturer 75 maintenance level 99 programming 75 operation 109 see also strobe synchronization 12 selection 60 synchronized signals 107 waterflow and silenceable circuits 74 non-silenceable 65 system silenceable 65 maintenance level 100 waterflow delay timer 71 system point 110 waterflow retard timer 109...
  • Page 164 Notes ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...

  • Page 165: Slide-In Labels

    Slide-in Labels Carefully cut along the outside of each label. Identify Function (F1-F4) keys as desired and slide the labels into the keypad. Starting at the center of the keypad next to the Function Keys, slide each label into the groove towards the outer edge. Function Keys F1 and F3 are not programmable in Canadian applications.
  • Page 166 ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023...

  • Page 167: 1000X, Es-1000Xc, And Es-1000Xi Operating Instructions

    ES-1000X, ES-1000XC, and ES-1000XI Operating Instructions NORMAL - Only AC POWER is illuminated green. PANEL KEY - The key to open the panel can be found at the following All other indicators are off. LCD display will read SYSTEM NORMAL. location: ________________________________________________________ WHEN AUDIBLE DEVICES ARE SOUNDING -...
  • Page 169 Manufacturer Warranties and Limitation of Liability Manufacturer Warranties. Subject to the limitations set forth herein, Manufacturer warrants that the Products manufactured by it in its Northford, Connecticut facility and sold by it to its authorized Distributors shall be free, under normal use and service, from defects in material and workmanship for a period of thirty six months (36) months from the date of manufacture (effective Jan.
  • Page 170 One Fire-Lite Place, Northford, CT 06472-1601 USA USA - Phone: (203) 484-7161 Canada - Phone: (905) 856-8733 www.firelite.com...

This manual is also suitable for:

Fire-lite alarms es-1000xcFire-lite alarms es-1000xi

Table of Contents