Honeywell Fire-Lite Alarms ES-1000X Manual page 70

Programming

Time
To change the time, press 1 while viewing the Time-Date Screen. The following screen will be displayed:
A flashing cursor is located toward the top left of the display. Below the cursor is the current time. To change the time, enter the two-digit
hours followed by the two-digit minutes. The cursor will move one position to the right each time a digit is entered. After the last minutes
digit is entered, the cursor will again move one position to the right. At this point enter 1 for AM or 2 for PM. The display will then return to
the Time-Date Screen which will show the new time entry. If an error is made while entering a digit, press the CLR key to delete the entire
entry and beginning again.

Date
To change the date, press 2 while viewing the Time-Date Screen. The following screen will be displayed:
A flashing cursor is located toward the top left of the display. Below the cursor is the current date. To change the date, enter the two-digit
month followed by the two-digit day and then the two-digit year (17 for 2017, 18 for 2018, etc.). The cursor will move one position to the
right each time a digit is entered. After the last year digit is entered, the display will return to the Time-Date Screen which will show the new
date entry. If an error is made while entering a digit, press the CLR key to delete the entire entry and beginning again.

Clock Format
The clock can be configured to display 12 hour (AM & PM) or 24 hour (military) time. Pressing 3 while viewing the Time-Date screen will
cause the display to toggle between 12HR and 24HR. Select 12HR for 12 hour display or 24HR for 24 hour display.
NOTE: If the clock is changed to 24 hour (military) format, the date will change to the European standard of Day-Month-Year (for display
purposes only).

Daylight Saving Time
TIME AND DATE
1=DAYLIGHT SAVINGS
Time & Date Screen #2
Pressing 1 while viewing Daylight Savings Screen #1 will cause the display to toggle between Enabled Yes and Enabled No. The control
panel will automatically update the time for daylight savings time when Enabled Yes is selected.
Pressing 2 while viewing Daylight Savings Screen #1 will display another screen which allows the programmer to select the month that day-
light savings time will begin. In this subscreen, pressing 1 will select March, 2 will select April, and 3 will select May.
Pressing 3 while viewing Daylight Savings Screen #1 will display two subscreens which allow the programmer to select the week of the
month that daylight savings time will begin. In the first subscreen, pressing 1 will select the first week, 2 will select the second week and 3
will select the third week, while in the second subscreen, pressing 1 will select the fourth week and 2 will select the last week of the selected
month.
Pressing 1 while viewing Daylight Savings Screen #2 will display another screen which allows the programmer to select the month that day-
light savings time will end. In this subscreen, pressing 1 will select September, 2 will select October, and 3 will select November.
Pressing 2 while viewing Daylight Savings Screen #2 will display two subscreens which allow the programmer to select the week of the
month that daylight savings time will end. In the first subscreen, pressing 1 will select the first week, 2 will select the second week and 3 will
select the third week, while in the second subscreen, pressing 4 will select the fourth week and 5 will select the last week of the selected
month.
70
10:00 AM
1=AM
MONTH DAY YEAR
12-18-22
Pressing 1 while viewing Time-Date Screen #2 will cause the following screens to be displayed:
DAYLIGHT SAVINGS
1=ENABLED
2=START MONTH
3=START WEEK
Daylight Savings Screen #1
ENTER TIME
2=PM
Time Screen
ENTER DATE
Date Screen
DAYLIGHT SAVINGS
1=END MONTH
YES
2=END WEEK
MAR
WEEK 2
Daylight Savings Screen #2
ES-1000X Series Manual — P/N LS10133-000FL-E:A 6/21/2023
Master Programming Level
NOV
WEEK 1