GE B30 Communications Manual page 457

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
PhDir1 SPS Indicates Phase Comparison of differential is satisfied per phase, where the last
digit of instance number 1, 2, or 3 refers to phase A, B, and C respectively.
The BUS 1 DIR A/B/C operand.
The STATOR DIFF1 DIR A/B/C operand.
PhsAInd SPS An LED.
The LED PHASE A operand.
PhsBInd SPS An LED.
The LED PHASE B operand.
PhsCInd SPS An LED.
The LED PHASE C operand.
PlOpn ACT Open pole detector is operated.
The OPEN POLE OP operand.
PosTotVArh MV SRC 1 Total VAr-hour in positive direction
PosTotWh MV SRC 1 Total Watt-hour in positive direction
ProcBusFail SPS Process bus system status.
The PROCESS BUS FAILURE operand.
ProcBusTrbl SPS Process bus trouble.
The PROCESS BUS TROUBLE operand.
ProjectedDif MV Phase angle difference between V1 and projected V2 (V2').
SYNCHROCHECK 1 DELTA PHASE', in degrees which is the phase angle difference
between V1 and projected V2.
ProjectedV1 CMV Projected V2 Voltage phasor.
SYNCHROCHECK 1 V2' voltage phasor, in primary volts.
PtpFail SPS Bad PTP Signal.
The PTP FAILURE operand.
Raise SPS PID 1 RAISE operand value
RawAnsp MV Raw neutral split phase current. Raw INsp in per unit.
RawAPh WYE Raw Id in per unit for Phase A, B, and C
RecBlk SPS Manually block autoreclose.
The BREAKER 1 BLK RCLS operand.
RecEna SPS Manually enable autoreclose.
The BREAKER 1 ENA RCLS operand.
RefWinding INS Reference winding. Number of windings used as the reference winding for ratio
compensation.
RelDpo SPS This data object indicates that not all criteria are fulfilled, and the switching/
operation action is not released to proceed. Complement of Rel.
The SYNC 1 CLS DPO operand, which becomes Off when all synchrocheck criteria
are fulfilled.
RemCmdAcsOff SPS Indicates operations of FlexLogic operand ACCESS REM CMND OFF
RemCmdAcsOn SPS Indicates operations of FlexLogic operand ACCESS REM CMND ON
RemMod SPS Capacitor control in remote mode.
The CAP 1 IN REMOTE operand.
RemSetAcsOff SPS Indicates operations of FlexLogic operand ACCESS REM SETG OFF
RemSetAcsOn SPS Indicates operations of FlexLogic operand ACCESS REM SETG ON
RemUnA SPS Indicates remote open pole condition is detected in phase A, B, or C.
The OPEN POLE REM OP phase A/B/C operand.
ReSigma SPC Command for the Hi-Z Sigma Value Reset
Restart SPS Indicates the motor has restarted.
The MOTOR RESTART operand.
RgDstIP VSG Expected value of Destination IP address field in messages subscribed to by
RxGOOSE#. The multicast IP address of subscribed R-GOOSE message.
RgRxMode ENG R-RxGOOSE1 Reception Mode setting: 0 = Unicast, 1 = SSM; 2=ASM
RgSrcIP VSG Expected value of Source IP address field in messages subscribed to by
RxGOOSE#. The source IP address of subscribed R-GOOSE message.
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical nodes...
B_DifPDIF, BusDifPDIF,
SttDifPDIF
LEDsIHMI
LEDsIHMI
LEDsIHMI
OpnPlΘSCBR
EnrMtrMMTR
EnrMtrMMTR
LPHD
LPHD
SynChkRSYN
SynChkRSYN
LPHD
PIDRegFPID
NeAUnPTOC
PhAUnPTOC
Bkr0XCBR
Bkr0XCBR
PctDifPDIF
SynChkRSYN
SecGSAL
SecGSAL
CapCtlGAPC
SecGSAL
SecGSAL
OpnPlΘSCBR
HiZPHIZ
MotThmPTTR
LGOS
LGOS
LGOS
3-219
3