GE B30 Communications Manual page 453

CHAPTER 3: IEC 61850 COMMUNICATION
Data object CDC Semantics
name
FltLoopRis MV D30, D60, L60, L90 - The fault loop resistance
FltMulti SPS Fault indication - Multi phase fault.
The PHASE SELECT MULTI-P operand.
FltRis MV L90 - The fault resistance at the fault point
FltSegment ENS L90 - Indicates in which segment of the line the fault occurred: 0 = N/A, 1 = LOCAL,
2 = REMOTE 1, 3 = REMOTE 2
FltSLG SPS Fault indication - single line to ground.
The PHASE SELECT SLG operand.
FltVoid SPS Fault indication - Fault type not detected.
The PHASE SELECT VOID operand.
FrcTrigger SPC Command for the Hi-Z Oscillography Force Trigger
FrstEthFail SPS First Ethernet failure.
The FIRST ETHERNET FAIL operand.
Function1 ENG Function Enable/Disable setting: 0 = Disabled, 1 = Enabled (note that TISSUE 670
suggests something like this named SetMod)
FwdOp SPS Fault direction is forward.
The NEG SEQ DIR OC1 FWD operand.
The NTRL DIR OC1 FWD operand.
GoDatSetRef ORG Expected value of datSet field in messages subscribed to by RxGOOSE#
The setting RxGOOSE1 DatSet.
GoEnaPort1 ENG Enable all GOOSE on Ethernet port setting: 0 = Disabled, 1 = Enabled
GoID VSG Expected value of goID field in messages subscribed to by RxGOOSE#
The setting RxGOOSE1 ID.
GndAmp MV Ground current.
The FIELD GROUND CURRENT in amperes.
GndNeutInd SPS An LED.
The LED NEUTRAL/GROUND operand.
GndRis MV Ground resistance.
FIELD GROUND RESIST in ohms.
STATOR GND. RESIST in kilo ohms.
GpsFail1 SPS GPS failed at terminal corresponding to instance number.
The 87L DIFF GPS 1 FAIL operand.
GrAct1 SPS Setting group corresponding to index is active (not instantiated in C30).
The SETTING GROUP ACT 1 operand.
GrdMasterID VSS Grand master ID actual value
Ha3NV MV Third harmonic component of neutral voltage.
STATOR GND 3RD HARM VN in volts.
Ha3ZroV MV Third harmonic component of zero sequence voltage.
STATOR GND 3RD HARM V0 in volts.
HiZIOC ACT Indicates phase instantaneous overcurrent has operated
HiZSt ENS Represents the status of Hi-Z fault detection function
HzChgRte MV Frequency rate of change measured value.
FREQUENCY RATE OF CHANGE 1 in Hz/s.
HzLedInd SPS An LED.
The LED FREQUENCY operand.
HzObAccum MV FREQUENCY OOB BAND 1 ACCUMULATION in percentage (%)
IdFail1 SPS ID check for a peer L30/L90 on the channel has failed.
87L DIFF CH 1 ID FAIL operand, which becomes On when the differential element's
ID check for a peer L30 on channel 1 has failed.
IndFailBeh ENG Setting to select the behavior of the RxGOOSE Boolean when the sending device is
offline: 0 = On, 1 = Off, 2 = Latest/On, 3 = Latest/Off
IndPos1 DPS Generic remote DPS input status values: 0 for intermediate-state, 1 for off, 2 for
on, 3 for bad-state.
RxGOOSE DPS1 actual value.
UR FAMILY – COMMUNICATIONS GUIDE
MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)
Used in logical nodes...
FltRFLO
PhSelGAPC
FltRFLO
FltRFLO
PhSelGAPC
PhSelGAPC
HiZPHIZ
LPHD
Master/LLN0
NegDocRDIR, NeuDocRDIR
LGOS
Master/LLN0
LGOS
FldGnd0PHIZ
LEDsIHMI
FldGnd0PHIZ, SubHaPHIZ
LinDfPDIF
Master/LLN0
TmClkLTMS
StatrPHIZ
StatrPHIZ
HiZPHIZ
HiZPHIZ
RteHzPFRC
LEDsIHMI
HzBnd$PTUF
LinDfPDIF
GGIO3
GGIO3
3-215
3