Cisco 4215 - Intrusion Detection Sys Sensor Configuration Manual page 467

Appendix C Troubleshooting
cat6k> (enable)
For Cisco IOS software:
cat6k#show module
Mod Ports Card Type
--- ----- -------------------------------------- ------------------ -----------
1
2
3
5
6
7
9
11
13
Mod MAC addresses
--- ---------------------------------- ------ ------------ ------------ -------
1
2
3
5
6
7
9
11
13
Mod Sub-Module
--- --------------------------- ------------------ ------------ ------- -------
5 IDS 2 accelerator board
7 Policy Feature Card 3
7 MSFC3 Daughterboard
11 IDS 2 accelerator board
13 IDS 2 accelerator board
Mod Online Diag Status
--- -------------------
1 Pass
2 Pass
3 Pass
5 Pass
6 Pass
7 Pass
9 Unknown
11 Pass
13 Pass
cat6k#
Note
If the status does not read
Step 3
router# set module power up module_number
78-16527-01
48 48 port 10/100 mb RJ-45 ethernet
48 48 port 10/100 mb RJ45
48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX
8 Intrusion Detection System
16 SFM-capable 16 port 1000mb GBIC
2 Supervisor Engine 720 (Active)
1 1 port 10-Gigabit Ethernet Module
8 Intrusion Detection System
8 Intrusion Detection System
00d0.d328.e2ac to 00d0.d328.e2db
0003.6c14.e1d0 to 0003.6c14.e1ff
000d.29f6.7a80 to 000d.29f6.7aaf
0003.fead.651a to 0003.fead.6521
000d.ed23.1658 to 000d.ed23.1667
0011.21a1.1398 to 0011.21a1.139b
000d.29c1.41bc to 000d.29c1.41bc
00e0.b0ff.3340 to 00e0.b0ff.3347
0003.feab.c850 to 0003.feab.c857
It is normal for the status to read
the diagnostics routines and comes online, the status reads
to come online.
, turn the module on:
ok
Cisco Intrusion Prevention System Sensor CLI Configuration Guide for IPS 5.0
Model
WS-X6248-RJ-45
WS-X6348-RJ-45
WS-SVC-IDSM-2
WS-X6516A-GBIC
WS-SUP720-3BXL
WS-X6502-10GE
WS-SVC-IDSM2
WS-SVC-IDSM-2
Hw Fw
1.1 4.2(0.24)VAI 8.5(0.46)ROC Ok
1.4 5.4(2)
5.0 7.2(1)
4.0 7.2(1)
1.0 7.2(1)
4.0 8.1(3)
1.3 Unknown
0.102 7.2(0.67)
4.0 7.2(1)
Model Serial
WS-SVC-IDSUPG 07E91E508A
WS-F6K-PFC3BXL SAD083305A1
WS-SUP720 SAD083206JX
WS-SVC-IDSUPG .
WS-SVC-IDSUPG 0347331976
when IDSM-2 is first installed. After IDSM-2 completes
other
Troubleshooting IDSM-2
Serial No.
SAD0401012S
SAL04483QBL
SAD073906GH
SAD0751059U
SAL0740MMYJ
SAD08320L2T
SAD071903BT
SAD05380608
SAD072405D8
Sw Status
8.5(0.46)ROC Ok
8.5(0.46)ROC Ok
5.0(1.1) Ok
8.5(0.46)ROC Ok
12.2(PIKESPE Ok
Unknown PwrDown
5.0(1.1) Ok
5.0(1) Ok
Hw Status
2.0 Ok
1.3 Ok
2.1 Ok
2.0 Ok
2.0 Ok
. Allow up to 5 minutes for IDSM-2
ok
C-41