Toro Greensmaster eFlex 1021 Service Manual page 157

Assembling the Handle Assembly (continued)
Greensmaster ® eFlex 1021
20248SL Rev C
2. If removed, install the lower handle assembly (1) onto the frame assembly (5)
and secure with the 2 bolts (2), anti-rotation washer (3),and washer (4).
3. Lift the lower handle assembly until it contacts the stop, and torque the 2
bolts (Item 2 in Figure
4. Install the handle mount (item 7 in
(10) and secure with 2 bolts (11) and 2 nuts (9).
5. Position the clutch bail link (5) in the handle mount (7). Install the spacer tube
(13) and 2 flange bushings (3) to the handle mount. Secure the clutch bail
link to the handle mount with the bolt (2) and flange nut (8).
6. Position the compression spring (6), spacer tube (13) and 2 bushings (3) into
the handle mount (7). Install the clutch bail assembly (4) to the handle mount
(7) and secure with the bolt (2) and flange nut (8).
7. If removed, install the left and right bail brackets (1 and 19) to the handle (20)
with the 2 torques-head screws (18).
8. Install the clutch bail assembly (item 4
the handle to the handle mount (7) with the 2 bolts (17) and 2 nuts (8).
9. Position the spring spacer (Item 24 in
(23) into the handle adjuster assembly (22). Install the handle adjuster
assembly to the upper receiver weldment (8) with the clevis pin (14), bearing
washer (15) and cotter pin (18).
10. If removed, install the lift assist handle (27) to the upper receiver weldment
(8) and secure with the bolts (11 and 16).
11. Slide the upper receiver weldment (item 8 in
assembly (19) and secure with the bolt (29) and flange nut (9).
Note: Do not tighten bolt and nut. Install the nut to engage locking feature.
The upper receiver weldment (8) must be free to slide.
12. Reposition the wire harness.
13. If removed, install the flange bushings (5), bolt (12) and flange nut (13) into
the brake lever (6).
14. Position the brake lever (item 6 in
(8) and secure with the shoulder screw (4) and flange nut (7).
15. Install the InfoCenter mount (item 4 in
with the 4 screws (1).
16. Install the wire harness.
17. If removed, install the flange bushings (item 31 in
throttle arm (1).
18. If removed, slide the throttle lever (34) onto the throttle arm (1) and secure
with bolt (32).
19. Torque tighten the bolt from 2.2 to 3.4 N·m (20 to 30 in-lb).
20. Install the throttle arm (1) to the handle assembly (3) and secure with bolt
(30), washer (2) and flange nut (20).
21. Install the bolt (item 21 in
receiver weldment (8). Ensure that the head of the bolt is resting the on
throttle arm (1).
22. Install the brake latch shaft; refer to
6–13).
87) to 95 to 101 N·m (70 to 75 ft-lb).
Figure 86) to the upper receiver weldment
Figure
Figure
Figure 84) to the upper receiver weldment
Figure
Figure 84) and 2 flange nuts (7) to the upper
Assembling the Brake Latch Shaft (page
Page 6–19 Controls, Wheels, and Accessories : Service and Repairs
86) to the handle (16). Secure
84) and handle torsion spring
Figure 84) into the lower handle
85) onto the handle and secure
Figure 84) inside the