GE N60 Instruction Manual page 270

FLEXLOGIC
Operand type
INPUTS/OUTPUTS:
Contact inputs
INPUTS/OUTPUTS:
Contact outputs,
current
(from detector on
form-A output only)
INPUTS/OUTPUTS:
Contact outputs,
voltage
(from detector on
form-A output only)
INPUTS/OUTPUTS:
Direct analog inputs
INPUTS/OUTPUTS
Direct inputs
INPUTS/OUTPUTS:
RxGOOSE DPS
5
INPUTS/OUTPUTS:
RxGOOSE Booleans
INPUTS/OUTPUTS:
Virtual inputs
INPUTS/OUTPUTS:
Virtual outputs
LED INDICATORS:
Fixed front panel
LEDs
LED INDICATORS:
LED test
5-154
Operand syntax
Cont Ip 1 On
Cont Ip 2 On

Cont Ip 1 Off
Cont Ip 2 Off

Cont Op 1 IOn
Cont Op 2 IOn

Cont Op 1 VOn
Cont Op 2 VOn

Cont Op 1 VOff
Cont Op 2 VOff

DIR ANA 1 DEADBAND
DIR ANA 1 FORCE
DIR ANA 1 INTEGRITY
DIR ANA 2 to DIRECT ANA 32
DIRECT INPUT 1 On

DIRECT INPUT 64 On
RxG DPS 1 BAD
RxG DPS 1 INTERM
RxG DPS 1 OFF
RxG DPS 1 ON
RxG DPS 2...
RxG Bool 1 On
RxG Bool 2 On
RxG Bool 3 On

RxG Bool 32 On
Virt Ip 1 On
Virt Ip 2 On
Virt Ip 3 On

Virt Ip 64 On
Virt Op 1 On
Virt Op 2 On
Virt Op 3 On

Virt Op 96 On
LED IN SERVICE
LED TROUBLE
LED TEST MODE
LED TRIP
LED ALARM
LED PICKUP
LED VOLTAGE
LED CURRENT
LED FREQUENCY
LED OTHER
LED PHASE A
LED PHASE B
LED PHASE C
LED NEUTRAL/GROUND
LED TEST IN PROGRESS
N60 NETWORK STABILITY AND SYNCHROPHASOR MEASUREMENT SYSTEM – INSTRUCTION MANUAL
Operand description
(does not appear unless ordered)
(does not appear unless ordered)

(does not appear unless ordered)
(does not appear unless ordered)

(does not appear unless ordered)
(does not appear unless ordered)

(does not appear unless ordered)
(does not appear unless ordered)

(does not appear unless ordered)
(does not appear unless ordered)

A deadband has triggered direct analog input 1
A user force operand has triggered direct analog input 1
An integrity timeout has triggered direct analog input 1
Same set of operands as per DIRECT ANA 1
Flag is set, logic=1

Flag is set, logic=1
Asserted while the RxGOOSE double-point status input is in the bad state
Asserted while the RxGOOSE double-point status input is in the intermediate
state
Asserted while the RxGOOSE double-point status input is off
Asserted while the RxGOOSE double-point status input is on
Same set of operands as per RxG DPS 1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1

Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1

Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1

Flag is set, logic=1
Asserted when the front panel IN SERVICE LED is on
Asserted when the front panel TROUBLE LED is on
Asserted when the front panel TEST MODE LED is on
Asserted when the front panel TRIP LED is on
Asserted when the front panel ALARM LED is on
Asserted when the front panel PICKUP LED is on
Asserted when the front panel VOLTAGE LED is on
Asserted when the front panel CURRENT LED is on
Asserted when the front panel FREQUENCY LED is on
Asserted when the front panel OTHER LED is on
Asserted when the front panel PHASE A LED is on
Asserted when the front panel PHASE B LED is on
Asserted when the front panel PHASE C LED is on
Asserted when the front panel NEUTRAL/GROUND LED is on
An LED test has been initiated and has not finished
CHAPTER 5: SETTINGS